Search Documents

By Peter Kolitsch, Galyn Rippentrop

INTRODUCTION On April 14, 1994, the joint venture of Kiewit Construction Company and Kenny Construction Company was awarded a 76 million dollar contract for the construction of the New Hampshire Avenue Tunnels in Washington D.C. The Notice to Proceed was given on May16, 1994 and scheduled completion is September 1997. This project is one of five contracts for the Mid-City E Line as part of the Washington Metropolitan Area Transit Authority (WMATA)Greenbelt Route. Once completed, the Mid-City E Line subway tunnels will connect service between the U Street-Cardozo and Fort Totten stations (See Figure 1). The New Hampshire Avenue Tunnels project consists of approximately 6800 feet of twin single track subway tunnels, three vertical shafts, associated utility work and comprehensive restoration work. Section E4b involved two methods of tunneling along the project alignment. The first method consisted of the well known soft ground open face shield driven tunnel and the second method consisted of tunnels driven using the New Austrian Tunneling Method (NATM) . The NATM section of twin tunnels begins at the Buchanan Vent Shaft and proceeds approximately 2630 feet under Rock Creek Cemetery, including the Farragut Emergency Access Shaft and connects approximately 390 feet beyond to the existing Fort Totten running tunnels (See Figure 2). Special considerations had to be given to the portion of the tunnel alignment which passed beneath Rock Creek Cemetery. The analyses and subsequent selection of the tunnel support system were based on anticipated geological conditions and the sensitive tunnel alignment. The New Hampshire Avenue Tunnels project was the second soft ground NATM project in Washington D.C. The first, by no coincidence, was completed at the adjacent Fort Totten Station and Running Tunnels Project by Mergentime/Hochtief, AJV. Currently, on a nearby WMATA jobsite, the J.F. Shea Construction Company has started a third NATM soft ground tunnel. Tunnel support systems were studied with respect to three tunneling methods: •A one-pass system consisting of a bolted precast concrete segmental lining •A two-pass system consisting of an unbolted precast concrete segmen

Jan 1, 1997

By N. K. Riddle

In many mines, it is typical to stockpile material for milling based either on analyses from exploration and blasthole drilling, or on the observation and judgment of experienced personnel. New analytical instruments make it possible to perform multiple, rapid analyses of as-mined samples at or near the mining face, so that sorting into stockpiles can be much more accurate. Using data and operating practices from a phosphate mine, a model was developed to simulate the function of analytical instruments in ore-grade control and ore stockpiling. With this model, it is possible to determine the recommended sampling points and sample frequency to obtain the desired confidence limits on the stockpile analyses.

Jan 1, 2003

By Pedro E. Rengifo

Splicing methods have undergone considerable developments over the last 2Oyears. Continuous conveyor belt service is dependent entirely on the strength and life of the splice to hold the two ends together. Ultimately, belting performance is dependent on the quality, efficiency, and technique of the splicer. As customers demand better belting performance and running tensions increase, the need for splices that perform as efficiently as the belting has increased also. Higher dynamic belt constructions have also dictated the need for "new"sp1icing techniques. Regardless of the belt type used or spliced, one item that is most necessary with all belt types is the quality of the workmanship and standardized splicing methods that employ all of the necessary elements required to ensure reliable field service. This paper will explore the use of Goodyear-issued internal standards for field splicing following the constraints of quality and efficiency for fabric and steel cord reinforced belting. Also included are the 10 most common mistakes made by splicers, Goodyear-issued Field Quality Assurance Standards, and check lists for end users to adhere to the manufacturers' requirements for splicing including materials and specifications for conveyor belt splicing and repairs.

Jan 1, 2004

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By T. Faulkner, S. A. Richards

"The Scale-Distance formula is one of the primary means of determining the maximum amount of explosives that can be safely detonated at one time by a single delay. This paper describes a method of applying the Scale-Distance formula to the entire mining area using gridded surfaces. Using this technique, the operator can better determine the economic impact of nearby structures on the mine plan. INTRODUCTION As the surface mining of coal and stone encroaches near populated areas, precautions must be taken to minimize blast vibration damage to protected structures. The common method employed to minimize vibration damage is not to reduce the total amount of explosive in the hole (which would negatively affect fragmentation), but rather to introduce delays to reduce the amount of explosive detonated at any point in time. The Scale-Distance formula, an industry-accepted standard, may be used to calculate the maximum weight of explosive that can be detonated at one time without damaging the structure. This information may then be used to determine the number of delays required for each hole. Detonators make up a large part of the cost of blasting. At roughly $15 per detonator an additional detonator in the hole can be significant. It is normal to set off hundreds of holes at in one shot. An additional detonator in each hole can cost additional thousands of dollars per shot. The number of detonators is also a function of the depth of the holes and the hole spacing. Being able to accurately forecast the economic impact of blasting near structures improves a company’s ability to make informed decisions on how to approach property owners. Operators basically have three options when dealing with property owners: 1. Buy the property and blast without restriction 2. Negotiate with property owner for a waiver to allow unrestricted blasting 3. Comply with the legal blasting restrictions This paper proposes a method for the engineer to forecast for all points in the proposed mining area the impact of nearby structures upon the blast design. Being able to create a contour map and ultimately estimate the number of delays required for the entire forecasted mining area, the engineer can create accurate economic forecasts of the cost of blasting. The objective is to reduce the level of uncertainty in the forecast of the blast component portion of the forecast."

Jan 1, 2016

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By A. J. Getz

Major precious metals projects are underway in Australia, Papua New Guinea, Indonesia, the Philippines and New Zealand. This article reviews the status of those projects. Included in this review are project location, reserves, method of resource exploitation, anticipated production, and other unique conditions. The article is limited to major precious metals projects in the Western Pacific region. This is not meant to negate the attractiveness or importance of the many other projects in that area. The geographical setting of these five countries are shown in [Fig. 1]. The gold output of the countries has increased dramatically during the 1980s. [Table 1] compares 1980 and 1988 production figures. The compound growth rate is 120%. That reflects the attractiveness of the region’s resource base as well as the impact of price increases, new exploration models and processing technologies, and changes in government policies. If the 10 projects discussed here are all brought onstream, their combined output - at about 130 t (4.17 million oz) - would amount to an increase of greater than 50% over 1988 production from this region. Table 2 shows indicative production levels for each of the 10 projects. Dollar amounts are in US currency unless otherwise specified. Australian dollars have been converted to US dollars at the rate of 1.28: 1.00.

Jan 1, 1990

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By E. M. Frizzell

In an effort to economically and efficiently enhance the erosion control aspects of present surface coal mine reclamation practices, the US Bureau of Mines has recently completed a two-phase research program wherein irrigation strategies and equipment developed under the first phase were field tested on three surface coal mine sites. The fundamental basis for the use of irrigation as a reclamation tool is to provide the plant moisture requirements as a supplement to prevailing natural precipitation, and thereby support the natural growth of drought-hardy native vegetation. Portable solid-set irrigation equipment and several irrigation strategies were tested on large 6-ha (15-acre) sites in Montana, Wyoming, and New Mexico. Results of these tests will be presented which include daily irrigations, precipitation levels, soil moistures, climatic data, and density cover and biomass of the native plants.

Jan 1, 1987

Fine coal is substantially more costly to process than coarse coal because of technical difficulties associated with separating fine particles and removing process water from both clean coal and refuse. Therefore, companies are often forced to discard coal fines to waste impoundments. According to a recent report published by National Research Council, the U.S. coal industry is discarding 70-90 million tons of coal fines annually to 713 active impoundments, most of which are located in Central Appalachia. On October 11, 2000, a 72-acre impoundment near Inez, Kentucky, accidentally released 250 million gallons of coal slurry into nearby underground mines, creeks, rivers, and schoolyards, thereby creating serious environ-mental concerns. Fortunately, recent advances in separation technologies make it possible to recover fine coal more efficiently from existing coal preparation plants and from waste streams previously discarded to impoundments. The availability of these new technologies allows companies to increase profitability and minimize environmental risks, which are conducive for achieving sustainable mining.

Jan 1, 2003

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

By Kal V. S. Sastry

Mineral processing simulation has come a long way since its beginning about thirty years ago. With our increased understanding of mineral process systems and the advent of new software and hardware technologies, we can visualize an ideal mineral processing simulator. This paper attempts to identify a number of desirable features of an ideal mineral process simulator and to describe the exciting trends in making such an ideal simulator a reality.

Jan 1, 1992

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By R. J. Weege

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. Our work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially' independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept as advanced by earlier writers to explain the concentration of the ore-bearing, fluids into broad shoots con¬stituting entire ore bodies is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body.

Jan 1, 1962

By Ahmed A. El-Saie

To reduce the problem of overbreak and its associated added costs, a new technique is proposed to make a slot around the tunnel profile in hard rock. The Finite Element Method was used to investigate the effect of the slot on the stress field and deflection of the tunnel core. Beam theory was also applied to calculate the stresses and deflections of a slotted tunnel for several different slot depths.

Jan 1, 1981

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on 'the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By C. R. Tatman

Failure to achieve the planned production rate at new mines and mine expansions has a major adverse impact on a project's economics. A study of 60 steeply dipping tabular deposit-type underground mines showed that 35% of the mines did not achieve their production goals. An empirical formula based on the geometry of the deposit and expressed as a rate factor is applicable to select a production rate for this type of deposit. The formula is: Annual production rate = Rate factor x Rate multiplier. The appropriate rate multiplier for each category of deposit thickness and the associated risk can be used to select an appropriate production rate.

Jan 1, 2002

By Ramon S. Pizarro, W. Joseph Schlitt

Introduction Trying to synthesize innovations occurring in gold processing is not simple. At present, this technology is exploding, brought about by the high price of gold. This price has compelled the mining industry, as a matter of survival, to produce gold. The frantic search for gold deposits continues, from glacial areas to tropical jungles. The search has been fruitful. New exploration techniques have helped to locate deposits. Some are amenable to conventional processing techniques. Others are in unusual settings that challenge the ingenuity of extractive metallurgists. Ore deposits containing traces of invisible gold, refractory mineralization, and impurities and deleterious materials that previously defied treatment are now being profitably processed. Metallurgists have developed various processing methods and equipment for gold ore treatment that reflect differences in ore characteristics, grade, mineralogy, reserves, topography, climate, and location. These processes can be categorized as: • For nonrefractory or readily leachable gold ores - vat leaching, heap leaching, and agitation leaching. • For ores containing free gold - gravity concentration methods, followed by mercury amalgamation, and • For refractory gold ores - flotation, roasting, pressure oxidation, followed by cyanidation leaching. In actual practice, a combination of these processes may be required. This is because gold mineralization, although usually simple, may be associated with other mineral species or with clays that make the ore difficult to treat. Furthermore, after the gold has been solubilized to form a cyanide complex, one of two important processes must be applied to recover the gold. These ore zinc cementation (Merrill-Crow process) and Carbon adsorption, desorption, and electrowinning. New techniques for leaching and recovery are also advancing. These will become the bases for the next generation of gold processing plants. Nonrefractory Gold Ores Nonrefractory ores with readily leachable gold are among the .easiest to treat. Even so, non-refractory ores from epithermal deposits are likely to contain too much clay. When these ores are damp, they may clog the screens and cone crushers. Depending on the type of process, scrubbing the crushed ore is very effective in overcoming clay problems. After dewatering, the slimes enter the cyanidation process and the thickener overflow is stripped of gold values and recycled. Semiautogenous (SAG) mills are also gaining popularity due to lower capital costs and ability to treat wet, sticky ores. If properly sized, the secondary crushing and screening plants, together with a secondary ball mill, can be eliminated. When the ore is of such a low grade that it can not support fine grinding, vat or heap 'teaching may be applicable. These systems are being actively applied in the US and elsewhere. Rapid construction and low capital costs are important features of these plants. Vat leaching is ideally suited for fast leaching ores and small tonnage deposits located in areas with harsh winters or wet tropical climates. For effective vat leaching, the ore is crushed to less than 25 mm (1 in.), agglomerated with lime or cement to control fines, and leached with sodium cyanide solution (upflow or downflow). The degree of size reduction is a tradeoff between increased costs of comminution and improved gold recovery from smaller particles. However, the size of material

Jan 11, 1984

By W. H. Jay, F. Lawson, D. F. A. Koch

Ion exchange resins may in the future displace activated carbon in gold plants where cyanidation is practiced. Recently patented technology based on interpenetrated polyurethane polymers shows that these new materials offer significantly improved loading kinetics over both activated carbon and commercially available ion exchange resins. These polymers are not restricted either in particle size or in density and therefore offer the gold industry the potential for a further technological advancement.

Jan 1, 1995