Search Documents

By Gerald G. Griswold, Allan G. Provost

"To Sink or Not to Sink"; this play on the Bard's words sums up the considerations and problems that face the owner on every potential shaft sinking project. The growing demand for access into the earth is pressing construction into new areas and to greater depths. The following discussion will entertain some of the effects of these new and unknown aspects upon the approach to designing and sinking of deep shafts. We will also look at the current shortages of equipment, materials and skilled manpower, and their effect upon the planning and sinking of shafts. Particular emphasis will be placed upon equipment selection, and we will discuss how economics, while always a prime consideration, is now, more than ever, both an incentive and a detriment to the industry. FUTURE CONSIDERATIONS Shaft construction is assuming ever increasing importance both in mining and civil endeavors. The rapid depletion of near surface mineral reserves is requiring the mining industry to look deeper into the earth for new sources. These greater depths increase the exposure to unfavorable geological conditions; heavier ground, high water pressures, and high temperature. South African gold mines have now reached depths of 12, 000 feet, where the rock temperature is 1380 and water bursts from the fissures. In North America depths to 7, 500 feet have been sunk, but deep shafts are still generally considered to be those of

Jan 1, 1974

By Kamran Esmaeili, MINGLIANG TANG

An understanding of the spatial and temporal variations of surface moisture content over a heap leach pad is essential for leaching production and to achieve a high ore recovery. The current leach-pad monitoring and data-collection practice remains highly labor intensive and exposes technical staff to cyanide solution, a hazardous material. To address these challenges, we propose using unmanned aerial vehicles (UAVs) equipped with thermal imaging sensors to remotely obtain image data with high temporal and spatial resolution for monitoring the surface moisture distribution over heap leach pads. A field study was conducted over a sprinkler-irrigated heap leach pad at El Gallo gold mine in Sinaloa, Mexico, and the acquired data were used to generate moisture distribution maps of the heap leach pad’s surface. The created moisture maps provide direct visualizations of surface moisture variation over the surveyed area. Such graphical results are effective tools for inspecting heap-leaching operations.

By Jonathan M. Pachter

The Bailey mining complex is located in Greene County, PA in the valley of Talley Run, a small stream tributary to the Enlow Fork of Wheeling Creek as shown on the location map insert found on Figure 1. The Bailey complex includes two Pittsburgh No. 8 Seam deep mines (Bailey and Bailey #2), a coal preparation plant, and two refuse areas (for disposal of coarse and fine processing waste). Clean coal is shipped from the complex via a 24.15 km (15 mile) rail spur, which connects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Company (Consol) began a permitting effort aimed at beginning construction of Bailey, the largest underground coal mining complex to be built to date in the United States. Construction of the Bailey Mine began in December, 1981, less than six (6) months following the first application submittal. Clean coal was produced by the Bailey Preparation Plant in September, 1984. Effective project planning, including early formulation of a project planning team, identification of "red flag" issues, innovative responses to environmental questions and development of environmentally sound project designs, all contributed to the relatively quick permitting at Bailey.

Jan 1, 1985

By L. H. Monaco

"The evolutional process is always about solving existent problems in order to provide further achievements. But the more something evolves, the more challenges it faces towards greater evolution. Industrial automation systems in Mining have also evolved a lot in the past decades, but they now face new challenges about integration: how to integrate different locations and systems, in a way to reduce costs and increase overall mine efficiency and safety for the operation. This paper compares conventional mining process automation architectures vs. a state-of-the-art, completely integrated system using Electrical Integration based on IEC 61850 standard for Substation Automation Systems. Emphasis is placed on the benefits to manage the entire mining plant as a whole, not only looking at the production rates, but also at the energy consumption for each part of process. In addition, it is discussed how an integrated system approach unlocks safety and productivity gains such as overall process optimizations, improved operator effectiveness, increased plant availability, and reduced maintenance costs. INTRODUCTION The world is constantly changing, and evolution is a natural part of mankind history. The role of evolutional process is to solve existent problems, but usually these solutions create new issues that need to be addressed. This scenario is also applicable to the industrial environment, in which the demand for higher profitability and efficiency on their processes requires solutions with more productivity using less resource. This is not different when it comes to energy consumption: how to optimize production rates and reduce energy costs at the same time? Regarding automation systems, the trend for the industries is to focus on four main challenges: how to provide safety for personnel; how to reduce initial investment for new plants; how to connect remote and in harsh locations; and above all how to deal with the lack of integration between several systems."

Jan 1, 2018

By James A. Finch, Xiang Zhou, Yue Hua Tan

Widely used as collectors for nonsulfides, amines also show some frothing properties. Evaluating frother functions of amines and their combination with conventional frothers addresses whether one reagent delivering both collector and frother functions compromises the efficacy of either. From the findings, whether blending with frother confers any benefit requires knowledge of the residual amine concentration. If it is below about 10 ppm, blending eliminated coalescence, but there appears to be no benefit if the concentration is above 15 ppm.

By A. P. Schissler, S. Badr, U. Ozbay, M. D. G. Salamon

Yield pillars are used in deep coal longwall mines, where the depth of cover is so great that a conventional chain pillar design tends to be unsuccessful. The design of yield pillars in deep U.S. mines has been based mainly on experience, pressure arch theories, numerical modeling, and empirical methods that originated in the eastern U.S. coal mines. This paper offers field experience based guidelines for the design of yield pillars through analysis and evaluation of numerous case histories. Case histories of yield pillar applications were collated and critically reviewed to identify trends in data that can be used to formulate the design guidelines. Convincing trends observed in the case of successful case histories indicate that yield pillars should have a width to height ratio in the range from 2.8 to 6.0, a stability factor during development between 0.4 and 0.6, and shed between 94% to 98% of the cover and abutment load, as provided by the Carr-Wilson (1982) method. Also, yield pillars should be utilized in coalmines only where the roof and floor rock have a CMRR rating of 50 or better.

Jan 1, 2003

By James H. Williams

More than 100,000 residents of Springfield and surrounding communities live on karst (sinkhole) terrain on the Springfield Plateau in southwestern Missouri. The city occupier much of the headwaters area of Wilson Creek basin, which is underlain by the Burlington Limestone (Mississippian), a cavernous, massively bedded formation averaging 150 feet in thickness. Sinkholes, some as deep as 75 feet, pock-mark the uplands. Stony red residual clay mantles the pinnacled limestone bedrock. Surface water lost to sinkholes and losing reaches of upstream areas resurges in springs and estevellas (reversible sinkholes) in the lower reaches of Wilson Creek. The Springfield Southwest Treatment Plant, an activated sludge process sewage treatment facility, situated about mid-basin at the confluence of Wilson Creek and a tributary, South Creek, serves the entire city. Effluent from the treatment plant together with industrial, street-wash and other waste from the-headwaters of the basin have degraded both surface and ground water quality in much of the Wilson Creek watershed. The area affected includes Wilson's Creek Battlefield National Park and recreational reaches of James River below the mouth of Wilson Creek.

Jan 1, 1970

By Richard H. Johnson

The Castle Mountain Mine (CMM) is located in the eastern por­tion of San Bernardino County, Southern California, 70 miles south of Las Vegas. The CMM is a joint venture between Viceroy Gold Corp. (75% and operator) and MK Gold (25%). The CMM initially started gold production with an 8,000 tpd cyanide heap leach operation in February, 1992 when the first ore was crushed and delivered to the leach pads. Even during construction and commissioning, design work was under way to engineer and construct a 1,200 tpd Mill circuit to process the higher grade fraction of the ore through use of pulp agglomera­tion. The need for a grinding circuit became evident with the quantity of high grade material delineated during drilling and the amount of visible gold that the geologists were finding in the drill core and R.C. cuttings. Viceroy did not want to stack the higher grade ore on the heap, and it was clear that permitting a tailings pond would, at best, be a long drawn-out affair. An alternative to a tailings facility had to be found.

Jan 1, 1996

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By Adrianus Halim, Jenni Hooli, Bartłomiej Skawina, Fredrik Sundqvist

Transitioning from diesel-powered loading and hauling machinery to battery-electric vehicles (BEVs) responds to the need for deepening underground mines as regulations become tighter. When using BEVs, exhaust gases and diesel particulate matter (DPM) emissions can be eliminated, and the energy required for the machines is used more effectively. Unlike their diesel counterparts, which are refueled, BEV loading and hauling machines — specifically, load haul dump (LHD) machines — can use battery swapping. This brings additional aspects to the operation that need to be considered, which have not yet been studied extensively. This study used discrete event simulation (DES) to analyze how the different numbers of BEV LHDs affect queueing and productivity when using different numbers of batteries and different swapping times in an underground block cave mine. The results identified the formation of working groups, where the machines swapped their batteries concurrently within each group, and their relation to the queueing time. Additionally, the minimum number of batteries per machine was identified to maximize productivity while minimizing queueing time. This study demonstrates DES as a powerful tool to assess and analyze conceptual systems and identify their underlying structures, which can enhance the deployment of BEV LHDs in underground block cave mine operations.

Apr 1, 2025

By Rudolf E. Greuer

Introduction The Institution of Mining and Metallurgy and the Institution of Mining Engineers organized the Third International Mine Ventilation Congress held in Harrogate, England. Sixty-one papers were presented and about 300 participants registered. About 30% of the participants came from Great Britain, 20% from South Africa, and about 5% each came from Australia, Canada, China, France, US, and West Germany. The remainder of the participants came from 18 other countries. Eleven of the papers presented dealt with methane, three with diesel exhausts, four with dust, four with radioactivity, 18 with heat, and 15 dealt with main and auxiliary ventilation. Six of the papers dealt with mine fires, which is a boundary region between main ventilation and gas concerns. Ventilation Congress proceedings are available. See ME, December 1984, page 1687, New Books page. With CH4 and radioactivity topics, the Australians dominated since they are becoming large coal and uranium producers. With diesel exhausts, the most important problem in highly mechanized mines, the North Americans were prominent. The South Africans, working in 90% SiO2 in their gold deposits, were preeminent in presentations on dust. They also led in topics related to heat, joined by the West Germans whose mines are getting deeper. In main and auxiliary ventilation, Great Britain and West Germany provided the majority of contributions. Methane The large number of methods for the precalculation of CH4 liberation in longwall mining all contain three elements: gas content of the coal, gas emitting zone (or influence zone of face), and degree of gas emission. Determination of the gas content, commonly accomplished by taking coal samples, does not pose much difficulty. But this is not the case with the other two factors. Most existing approaches rely on rock mechanics observations. Some only rely on intuition or speculation. The West German coal mines conducted a large research project between 1977 and 1982, in which gas pressures around longwall faces were measured. Gas pressures and gas contents can be related. Therefore, influence zone and degree of gas emission can be determined simultaneously. The precalculation of CH4 liberation in room-and-pillar mining is simpler. Since foot and hanging walls remain essentially intact, gas pressure distribution and gas flow can be calculated using hydraulics equations. A key to these calculations is permeability. A group of Australian researchers reported that the permeabilities of rock under three dimensional stress differs from rock under destressed conditions. This fact was known, but no systematic observations existed. These were provided. Methane drainage has been practiced for more than 40 years. It is used with great success in longwall operations. Some of the West Germans think that methane drainage from the footwall is neglected. Under certain geological conditions, they claim this is as important as drainage from the hanging wall. A research project was presented in support of this claim. Considerable efforts have existed for more than 10 years to use methane drainage in room-and-pillar mining. A paper described the accomplishments of Consolidation Coal Co. Since coal and rock are not fractured as much as in longwall mining, gas transport takes place by the slow diffusion from micropores into the cleats. Then, it is transported by laminar flow along the cleats until a drainage borehole or the mine workings are reached. Boreholes about 300 m (1000 ft) long can reduce the gas content of a band of coal 100-m (330-ft) wide by 50% in one year. A paper from India described methane drainage from gob areas. A French paper reported that especially high methane concentrations can be drained from gob areas if the face ventilation is descensional. Methane buoyancy and ventilating pressures compensate each other, and little air dilution by leakage takes place. Another French paper described a newly developed gas and air velocity monitoring system making use of a microcomputer. Four papers on methane dealt with gas outbursts. Two Australian contributions described the problems encountered with CH,-CO2 mixtures and the attempts to solve them with drainage boreholes having 10 to 20-kPa (1.5 to 3-psi) suction pressures. A Hungarian paper described problems and attempts to reduce the risks of gas outbursts in Hungary. Prediction of gas outbursts in coal seams was the focus of an English paper. Observations show that they are frequent when coal, through its geological past, has become soft and brittle with a resulting increased desorption rate. An instrument for gravimetric de-

Jan 1, 1985

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By Steven I. Majtenyi

INTRODUCTION The heavy risk inherent in all underground construction projects contributes significantly to the high cost of transportation tunnels. First, the knowledge of this risk leads the engineer to design conservatively. Second, the cost overruns are still common with a high proportion of them originating from corrective measures needed when unforeseen problems develop during excavation. These unforeseen problems includes - encountering unexpected objects, materials and water conditions - experiencing an unforeseen behavior of the materials - damaging property beyond the expected range of influence of the tunnel construction. To minimize these expenses, more emphasis is being placed on well planned and interpreted site investigation programs in the final design and planning stages of the project. It is well known that the cost of a planned excavation is less than the cost of dealing with the same conditions when they are encountered unexpectedly. Therefore, the objective of site investigation is to provide a complete set of reliable data for designers and contractors that is continuous along the projected tunnel alignment. Two alternatives axe available to achieve this objective; - for shallow tunnels, it is often feasible to generate continuous data by drilling appropriately spaced, vertical bore holes and applying sensing techniques for interpolation (1, 8). - for deep tunnels, or certain urban tunnels under existing structures, closely spaced, vertical bore holes are not feasible except for narrow zones at the portals. In such cases direct horizontal penetration may be required that may be complemented by radial sensing to extend the range of information.

Jan 1, 1976

By Mortimer J. Richardson

Dredging can be traced to early times where it may have been derived by the Phoenicians prior to the 4th century B.C. The first tangible design drawings of a bucket ladder (BL) dredge can be found in the collections of Leonardo da Vinci (1452-1519), which he produced when he was attempting to create better methods of channel and port dredging. The perfection of the system did not commence until after the invention of the steam engine in the early 1800's; providing the impetus to progress from man-powered mud mills, horse drawn along polders or dikes in the Netherlands, England, France and Germany, to steam-driven. In the 1860's following the various gold rushes in the U.S., Australia, New Zealand, Siberia and South America, with placers in particular, efforts were begun to apply mechanization to achieve deeper digging. There is a recording of a dredge being installed to mine gold in Montana in the 1860's but did not include a processing system. Then in the 1880's in New Zealand, some practical engineers developed a system that is said to be the first bucket ladder mining (BL/M) dredge for mining gold placers. In studies of the New Zealand gold dredging experience, it is estimated that some 500 dredges were built to mine gold between the 1880's and 1942. A careful analysis of the data, however, shows that very few were profitable. The technology appeared to stagnate in the early part of the century. Two of the BL/M dredge design engineers left New

Jan 1, 1992

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The paper investigates the influence of slope height, slope angle, slope material, and rock size on rockfall runout distance in openpit mines. Using statistical analysis and simulation, the study aims to improve rockfall hazard assessment and catch bench design by identifying key variables affecting rockfall behavior.

Oct 1, 2023

By Charles E. Robertson

As it becomes more and more apparent that our nation must place a great deal of reliance on coal as an energy source in the coming decades, prospecting for new reserves Un Missouri and other states in the Western Interior Region is increasing. As more and more of the known reserve becomes committed to existing or planned projects operators will be forced to look beyond the fringes of existing coal fields for additional reserves. Perplexing geologic problems invariably confront all prospectors and are particularly bothersome to those new to a particular area. It is the purpose of this paper to alert prospective operators to geologic problems likely to be encountered and to offer guidance in the recognition and solution of these problems. Particular emphasis is placed upon geologic structure and washouts. Other geologic problems have been discussed in a previous paper.

Jan 1, 1977

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

By Todd Loudin

A majority of the chemical process industry uses lime in either a powder or liquid form. Engineering and maintenance personnel often face a long and potentially expensive trial-and-error period in order to find the best process equipment to handle lime. Limestone is mined from a quarry in the form of calcium carbonate (CaCO3). Then, it is crushed and fed into a kiln at approximately 1,093° C (2,000° F), where the carbon dioxide is burned off (calcining) to make calcium oxide (CaO).

Jan 1, 2010

By Tim O’Neil

Until about three years ago, Asarco's copper business consisted predomi¬nantly of custom smelting of ores and concentrates produced by other mining companies. Since then, the company has been transforming itself into a fully integrated producer in copper mining, smelting, and refining. In doing this, Asarco has lowered its costs and restructured its operations and finances. Now, Asarco hopes to complete this process by spending $260 million over the next three years, to expand and modernize its copper facilities and boost production by some 40%. The capital spending program includes: • $130 million at the Ray mine about 113 km (70 miles) north of Tucson, AZ, to expand mining capacity and install an in-pit ore crusher, mill, and concentrator; • $100 million, to expand the mining capacity at the Mission Complex located south of Tucson, AZ, and refurbish the adjacent, idle Pima mill and concentrator. (Asarco had earlier exercised an option to purchase the Pima mill for about $6 million); and • $30 million, to modernize the copper smelter in El Paso, TX, with a new flash smelting process. The new program is in addition to a recently completed first-phase expansion of the Mission mine, mill, and concentrator. This $13 million debottlenecking of existing operations in¬creased production capacity by 46% or 24.5 kt/a (27,000 stpy), to 79 kt/a (87,000 stpy) of copper in concentrates. In addition, a previously an¬nounced $12 million expansion program at the Ray mine is scheduled for completion in early 1990. It will expand mill capacity, to offset the anticipated effects of increasing ore hardness as the pit deepens. Ray produces 68 kt/a (75,000 stpy) of copper in concen¬trates and an additional 36 kt/a (40,000 stpy) of electrowon copper. By 1992, when Asarco's expanded and modernized copper facilities are operating at capacity, the company's mine output will have increased by 67 kt/a (74,000 stpy), to 263 kt/a (290,000 stpy) of contained copper. That will be enough to provide all of the feed required for Asarco's two copper smelters - by then, both of them modern, state-of-the-art facilities. Asarco's expansion and modernization program will further reduce costs and provide added assurance that the company's copper business will be profitable at the bottom of the cycle, according to Chairman Richard de J. Osborne The Ray mine portion of the new program will include construction at the mine of a new mill and concentrator, with a capacity of 18 kt/d (20,000 stpd) of ore. These new semiautogenous grinding mills and large capacity flotation cells will augment the present 27.2 kt/d (30,000 stpd) concentrator located 29 km (18 miles) away, in Hayden, AZ. A 29 km (18 mile) pipeline will be built to carry tailings in slurry form from the new Ray mill to the present tailings pond. Concentrates from the new facility will be shipped by rail to Asarco's Hayden copper smelter. Ray's present 27.2 kt/d (30,000 stpd) crusher, adjacent to the open-pit, will be replaced by a 54.4 kt/d (60,000 stpd), portable in-pit crusher and conveying system. This will reduce the more expensive ore haulage by truck. The Ray project is scheduled for completion by 1992. It will increase the mine's annual output of copper in concentrates by an additional 33.5 kt/a (37,000 st), to 102 kt (112,000 st). And the project could mean an additional 400 jobs at the 730 employee Ray operation. Work at the Mission Complex involves reactivation of the Pima mill and concentrator and expansion of mine output sufficient to provide ore to both the Pima mill and the present Mission mill. In 1985, Asarco purchased the Pima mine, which occupies one end of the Mission pit. The work at Mission will increase its annual capacity by 33.5 kt (37,000 st), to 112 kt/a (124,000 st) of contained

Jan 1, 1989

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974