Search Documents

By E. Craig Simmons

Uranium is an element incompatible with respect to the major rock-forming minerals crystallizing from granitic magma, entering in- stead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late- stage fluids which can form ore deposits directly, or labile U which can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U- enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks which are most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite Mine area, Washington, have geochemical characteristics which fit very well the model presented here. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1981

By Y. C. Kim

Three rock fracture parameters define three points along empirical cumulative size (of rock fragments) distribution curves at Inspiration copper mine. These parameters are: rock quality designation (RQD), longest piece of intact rock and % of +1 inch. The RQD and the longest piece are actually measured on drill hole cores whereas % of +1 inch is visually estimated on the same cores. These size distribution curves are then utilized in a variety of engineering applications such as; slope instability analysis, blast design, copper recovery prediction from heap leaching, etc. The three rock fracture parameters for two dominant rock types (porphyry and schist) in the pit had to be estimated separately due to different rock fracture characteristics.' Both ordinary kriging (OK) with measured hard data only and soft kriging (SFTK) with hard and soft data were used to estimate each parameter. The cross validation of 100 measured sample values served as the-basis for evaluating the potential benefits of SFTK over OK. Use of subjective information during SFTK required obtaining (prior) probability distributions for all three rock fracture parameters. These distributions were obtained from the typical rock fracture parameters observed in drill hole cores falling inside the geologically interpreted structural domains with varying degrees. of fracture intensity and also through direct mapping along the exposed bench faces. Two different types of soft information were developed for this study; namely, Type "A" and Type "K". The former is based on sample distribution of fracture parameters whereas the latter is based on two step estimation designed to narrow the range of variation observed in data Type "A". The results of the cross validation were analyzed using a linear regression of actual values versus estimated values. The results confirm an improvement on the estimates made by SFTK with hard and. both types of soft data over those produced by OK with hard data only.

Jan 1, 1989

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

Caterpillar and Fortescue Metals Group have moved forward with the delivery, installation and support of a complete Cat MineStar System at Fortescue?s Solomon iron ore mine in the Pilbara region of Western Australia. The complete technology suite was implemented for the first phase of Solomon, the 20 Mt/a (22 million stpy) Firetail manned mine, in October 2012. As part of an autonomous mining solution for phase two, the 40-Mt/a (44-million stpy) Kings Mine, eight Command for hauling Cat 793F CMD trucks were commissioned and commenced operations in the second quarter of 2013. The mine plan calls for a progressive ramp up to 45 autonomous trucks during the next several years. In addition, other Cat MineStar System capability sets, Fleet, Terrain, Detect and Health, are being used across the mobile equipment fleet, including support equipment and light vehicles. Working closely with Fortescue and its mining contractor, Leighton Contractors, Caterpillar and the Cat dealer in Western Australia, WesTrac, are providing a full solution for managing, operating and supporting Cat MineStar System and Command for hauling. The greenfield Solomon Mine has brought together the skilled team from Caterpillar, Fortescue, Leighton Contractors and WesTrac to deliver an efficient, cost effective autonomous mining solution.

Nov 1, 2013

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By I. Iwasaki

Rest potential, cyclic voltammetry and chronopotentiometry measurements were made to study the effects of cathodic polarization of chalcopyrite, simulating the mineral contacted with grinding media under a nitrogen atmosphere. The reaction products on the chalcopyrite surface were identified by XPS, and the mechanism of the cathodic reaction was proposed. Microflotation tests were performed to investigate the effects of surface changes on the floatability of chalcopyrite.

Jan 1, 1993

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By Daniel Saramak, Agnieszka Saramak

A big issue in crushing and grinding operations in raw materials handling is high energy consumption and low breakage effectiveness. According to the Legendre [7], only 10% of energy input is directly consumed on the feed material breakage, while the remaining portion is dissipated in the form of heat and noise [8]. In the industry of limestone powder production, the grinding operations constitute integral part of technological circuits, and the energy consumption in operations of industrial comminution consume as high as 2% of world energy [14]. High-pressure grinding is the technology with proved energy benefits both in ore processing circuits and in limestone grinding. The promising results concerned mostly the achieved energy savings and good results of material breakage were achieved and demonstrated in numerous investigations [1,3,12]. However, it appears that a proper selection of operational parameters of the press devise, determination the feed material characteristics and adjustment of process course san be of a key-significance in improving an effectiveness the HPGR operation. Operational parameters of devices and process course should be verified towards the characteristics of the feed material, which mainly applies to the particle size and shape of the feed material and its moisture, and also mineralization in case of ores [2,4,9]. There are various investigations concerning an impact of the operational pressing force on comminution results which mostly refer to the determination of energy consumption and crushing ratio [5,6,10,13]. Investigations on the moisture content are less common, however their results suggest that, in general, the HPGR feed with higher moisture shows the tendency to higher comminution intensity, while the energy consumption increases together with increasing of feed material moisture. Investigations on olivine sand feed [11] showed that crushing ratio decreases for higher moisture, especially when the material is crushed at higher pressing force. HPGR devices, however, shouldn’t be regarded as a unique and perfect solution for comminution of each type of material. But they indeed may bring technological and economic benefits, comparing to conventional crushing and grinding machines, resulting in more favourable breakage of material particles and lower consumption of energy per unit mass of processed feed material.

Feb 1, 2025

By James W. Evans

It appears that all extractive processes involve, at one or more points, fluids (gases or liquids) and that the flow of the fluid is an essential part of the functioning of the process. Usually that flow is turbulent and the turbulent flow frequently determines the rates of mass and heat transfer as well as other important phenomena such as bubble/droplet breakup and coalescence, particle suspension, etc. Over the past decade many attempts have been made to model turbulent flows in metallurgical unit operations. The present paper summarizes some of that work. Amongst the operations considered are agitated leaching, ladle metallurgy, electrowinning/refin- ing, induction furnaces, Hall cells and electro- magnetic casting. Where possible, comparisons are made between model predictions and experimental results.

Jan 1, 1990

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multielement ground support system, there is a need to know the support characteristics that the shotcrete contributes to the overall system. To quantify the support provided by the shotcrete, flexural strength tests were conducted with two common, commercially available fiber-reinforced shotcrete (FRS) mixes using the round determinant panel (RDP) test method, ASTM C 1550. A portable RDP test machine developed by NIOSH researchers was used to determine the peak flexural load and residual load capacity for a steel FRS and a synthetic poly FRS that were sprayed using dry mix procedures and equipment. Besides the flexural strength and loading behavior determined from these tests, a method was also developed for measuring the width of cracks exposed on the underside of a shotcrete panel during a RDP test and relating these measurements to residual load values. Quantifying the peak flexural load and residual loads of a shotcrete mix through on site testing at a mine and visually assessing the loading cycle and load-carrying capability of the shotcrete applied to underground workings will improve mine safety by providing a better assessment of the stability of shotcrete supported entries.

Jan 1, 2010

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of the operational variables on the concentrate grade, recovery, separation efficiency and kinetic parameters of the copper flotation process. The results indicate that concentrate collecting time and pulp density were the parameters with the greatest effects on the concentrate grade. Considering copper recovery, the concentrate collecting time, collector dosage and pulp density were the most significant variables, in decreasing order of importance. The separation efficiency was found to be mainly influenced by the concentrate collecting time. This study can be helpful in identifying the parameters with the most effects on flotation performance and, consequently, the overall process efficiency, including recovery and separation efficiency. Such an outcome can be used as a decision-based tool to apply the necessary changes in a real-life industrial operation in a more effective way to improve the quality and quantity of the flotation concentration.

By Karl J. Benecke

Though the first patent on a bucket wheel excavator was granted in 1881 in the U.S. this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with the development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generating, despite the low heating value of German lignite in the order of 8500 kJ/kg (3600 BTU/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is in the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output open pit mines. The largest one, Fortuna Mine in the Cologne district, produced a, total of 45 000 000 t lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95 200 000 bank m3 equal to 200 000 000 t overburden had to be removed to accomplish this lignite output. The largest BWE (Fig. 1) ever built is working in the Fortuna Mine, too. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 t, its wheel diameter 21.6 m, as high as a 7-storey building.

Jan 1, 1977

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By Joseph Keenan

In March of 1994, Dynatec Mining Limited entered into a contract with PCL Civil Constructors to carry out the underground excavations for the Algonquin Power Corporation’s15 Megawatt Nagagami hydro-electric power station located near Hearst, Ontario, Canada. Dynatec completed the work for this project in early October 1995. Dynatec Mining Limited’s work included the excavation of a 175 meter long penstock driven at a grade of -25% to a 4000 m3 powerhouse located 50 meters below the intake elevation. A 1200 meter long tailrace was driven from the Nagagami River to connect with the powerhouse. Two 50 meter raises were driven from the powerhouse to surface to pro-vide access for equipment and personnel. The excavation of the tailrace tunnel(5.8m x 5.9m) was completed using Dynatec’s Long Round Jumbo Technology.

Jan 1, 1997

By D. Leppert

Clinoptilolite zeolite may offer attractive, cost-effective alternatives for remedial cleanup of old minesites, smelters and other sites with heavy metal contamination. Previous research demonstrates the relatively strong affinity of clinoptilolite for numerous metals and clinoptilolite displays a particularly strong affinity for lead (Loizidou and Townsend, 1987), one of the most toxic and problematic heavy metals. Since clinoptilolite can also selectively absorb some radionuclides and organic compounds, it may offer practical solutions to a wide variety of environmental problems.

Jan 1, 1989