Search Documents

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn&apos;t been possible to include the necessary physics of the particle stressing process to allow the development of a &apos;ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

Western Energy Co.&apos;s Rosebud mine in Colstrip, MT, has implemented innovative mining techniques in the past,* and following in that tradition, new techniques for overburden removal were recently introduced at the Montana coal mine. In April 1979, falling coal production left Western Energy in a bind. At that time the company was one of the first to implement a dozer/scraper stripping system for additional stripping capacity. This time around, however, the challenge was to eliminate spoil rehandle with a dragline while digging down 33 in. "Rehandle will increase 20% by going down an additional 3 m past the 24-m level," according to Bob Cope, mine supervisor for Western Energy. To cut this additional expense by eliminating the need to rehandle, Western now uses scrapers to bench down for the dragline. This system utilizes the flexibility of scrapers as earthmoving tools. Although scrapers were originally purchased to fill an immediate need for productive, low-cost overburden stripping, they are now benching and continue to optimize the overall effectiveness of existing draglines. According to the company, the draglines couldn&apos;t keep up with production requirements if they had to rehandle spoil material. Benching with the scrapers eliminates spoil rehandle. Western Energy expects to produce 10.6 Mt of coal this year from three active pits in the Rosebud mine. Western estimates that there are enough coal reserves at Rosebud to support a 40-50 year operation. The sub-biturninous coal has an energy value of 9.2-9.4 Mj, 0.87% sulfur, 8% ash, and 20% moisture. Pit A, approximately 610 m long and 45-55 m wide, is the mine&apos;s greatest producer. A Marion 8050 dragline with a 46-ms bucket digs 30-33 m to uncover the 7.3-m Rosebud coal seam. Here, the scrapers were put to work benching for the dragline. Long Construction Co., which operates the mine equipment for Western Energy, uses four Caterpillar 637 tandem-powered scrapers, two Cat 631s and two Terex TS-24s. The number and combination of scrapers actually used for benching periodically changes, depending on which ones are needed for topsoil removal and reclamation. Scrapers benched down about 9 m and removed nearly 2.3 Mm of over-burden at pit A. About 1 Mm was placed in a 9-m lift on top of the high-wall at the head of the pit. The scrapers built up one side of the lift first and then the other on successive passes to

Jan 2, 1981

By C. W. Benjamin

The paper covers the development of an efficient, "state-of-the-art" design approach encapsulating extensive research and development by Gulf on soft loading, low impact, zero spillage transfer chutes. The development, which interacts and interfaces the comprehensive methodologies for transfer chute design, allows Gulf to deliver detailed designs within 8-24 hours rather than the norm which is weeks or months. Outputs include 3D models of completed transfers and support structures along with rendered 3D representations of the design which can be fully manipulated around all axis in 3D.

Jan 1, 2000

By William F. Kane, Eric C. Drumm

Rock slope failures in the Great Smoky Mountains of Tennessee are a continuing problem. A study of the geotechnical factors affecting such slopes was conducted in this geologically complex region. Seven rock slopes, five of which had undergone failure, were identified and mapped. Other parameters were mapped in addition to the standard geologic and geometric parameters. These were joint frequencies across and down the slope, and surface hardness from Schmidt hammer tests. Regression analysis on the various data revealed that Schmidt hammer hardness correlates very well with joint cohesion back-calculated from failure geometries. This approach suggests an alternative means for estimating joint strength.

Jan 1, 1986

By Greg R. Wheeler

Few members of the general public have a clear understanding of mineral resources. Most people do not know how minerals are mined or why they must be extracted from many diverse locations. Many people acquire knowledge of mineral development from mass media sources with incomplete details or obvious anti-mining bias. The California Mineral Education Foundation was formed in 1991 to provide educational opportunities for the public and industry. There have been major changes in earth science teaching requirements for kindergarten through 12th grade (K-12) curricula since the passage of California Senate Bill 813 in 1983. Model graduation standards, curriculum standards and the state science framework mandate substantial coverage of geoscience topics. The California State Commission on Teacher Credentialing has completed changes in multiple subject and single subject science credentials which will require more geoscience preparation for all teachers. The need for pre-service and in-service education in geoscience is at an all time high. Teachers must have continuing education to maintain their credentials and many are now seeking information in geoscience. The California Mineral Education Foundation designed and conducted the California Mineral Education Conferences held in August 1991 and 1992. The conferences involved lectures and field trips on mining geology, environmental problems and political concerns. Master teachers were employed to share how they get across mineral resource concepts in the classroom. Ninety-six percent of the participants stated that they had changed to a more positive perception of mining after taking the three day course.

Jan 1, 1995

By P. W. Hunter

The construction of a major sewerage scheme requiring 15.3 km of 5.5m excavated diameter tunnel in basalt, mixed and soft ground has been undertaken by the Melbourne and Metropolitan Board of Works. A double shielded Tunnel Boring Machine was selected to excavate 13.7 km of basalt and mixed ground. Advanced methods for recording operational data on the TBM were introduced. Progress to date has shown that the TBM can excavate rock very effectively with a best weekly production of 178.8m; soft ground has been encountered and successfully handled.

Jan 1, 1987

By Louis W. Cope

Placer material, regardless of the value of gold, tin, titanium, diamonds or other value mineral it contains, remains worthless until the valuable constituent is separated from the bulk of the material. This separation is no mean task when considering that a gold placer containing 0.01 to 0.03 oz/yd3 of gold, which is the range of grade of typical placer deposits; yes, 1:3,000,000! It is a miracle that gold placer mining has ever been profitable. Added to the situation of minute quantities of gold are several other problems, such as the gold often being very finely divided, the association of boulders and clay, and running and/or ground water. As each placer deposit is individual and distinctive, many factors have to be considered in planning the method for gold recovery from the alluvial deposit. Previous chapters have shown that in the exploration and sampling stage, some knowledge of the amount of each size of coarse and fine material which occurs in the deposit as well as the size distribution of the discrete gold particles is determined. Unless informed to the contrary, as a general rule of thumb, plant designers will consider that 40 percent of the material will pass through a 5/8-inch screen or punched plate hole. Also that there may be an occasional nugget and normally considerable amounts of fine gold. The designer must

Jan 1, 1992

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

By Robert E. Goodwin

There are four main requirements which must be considered when selecting a wire rope for the best serviceability. A proper choice is made by correctly estimating the relative importance of each of these requirements and selecting s rope which has those qualities best suited to withstand the combination of destructive forces expected under continued service. A wire rope should possess: 1. Strength sufficient to support the maximum load expected and with s proper safety factor. 2. Ability to withstand bending and to resist bending fatigue without failure of the wires. 3. Ability to withstand surface abuse such so abrasive wear, pounding, and wire scrubbing. 4. Ability to withstand abuse such as crushing and distortion.

Jan 1, 1968

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By T. Ertekin, R. V. Ramani, W. Sung

The emission of methane in the coal mine working faces has two immediate impacts with regard to coal mine planning. Firstly, at the planning stage, the coal mine ventilation system must be designed such that airflows in the faces keep the concentrations of the gas in faces areas to below one percent. If the concentrations were greater than one percent, the production machine has to be shut down resulting in a loss of productive time. In an extreme case, concentration can reach explosibility limits which may lead to ignitions and explosions. Secondly, in excessively gassy coal seams, several alternatives can be applied to the mine layout configuration, and the mining method to be predicted for the extraction of coal, so as to insure a productive and safe operation. In this study a two-phase, two-dimensional finite-difference model was used to predict the methane emission rates into active mine working area under several methane drainage schemes. The numerical model utilizes a recently developed multi-mechanistic flow theory which describes the flow of methane in an heterogeneous and anisotropic coal seam. Transport of methane in the micropore structure of the coal is described by the Fick&apos;s law of dif- fusion under the influence of existing concentration gradient, while flow in the more permeable butt and face cleats (macropore spaces) is formulated by Dar- cy&apos;s law under the influence of existing pressure gradient. The desorption of the methane is accounted with the aid of a quasi-steady kinetic sorption model. A series of simulation studies were conducted in a systematic manner by sifting through the parameters associated with the coal seam characteristics and the degasification strategies in order to understand those which most significantly affect the methane emission rates in the face areas during mining. Along these lines, the effects of coal seam properties such as thickness, porosity, permeability, sorption characteristics and scheduling of drainage process against the mining operation have been isolated to understand the role of each individual parameter on the methane emission rates.

Jan 1, 1987

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021

By R. T. Swinderman

"Virtually every article you read on safety has a statement to the effect: “It’s obvious that safety pays”. If it is so obvious, why is it so hard to answer these questions? • How does the Maintenance or Operations Manager convince the Plant Manager to spend money from the annual budget for safety improvements? • How does the Plant Manager influence Corporate to prioritize safety improvements? • How does an engineering firm persuade the owner to spend more on design and equipment up front to reduce risk? There are many cultural and structural reasons why it is so difficult to prove the obvious. In my opinion the main culprits are: the almost universally used ‘Low Bid’ process, variations in reporting incident statistics between industries and countries, and, the Generally Accepted Accounting procedures (GAAP) [or International Financial Reporting Standards (IFRS)]. Conventional wisdom is it’s smart not to spend more than you need to meet the minimum regulations and maximize production. But buying on price alone often harms people, degrades the environment, and reduces the company’s bottom line. How can this be? You met the minimum safety requirements and saved money by buying on price. Don’t those savings go right to the bottom line? When you buy on price you get minimum quality, minimum compliance and are often backed corner with no reasonable options to rectify the problems that arise from buying on price instead of buying on long term life cycle cost. Culturally few companies actually ‘walk the talk’. It is trendy to have giant billboards at plant entrances proclaiming world class compliance with quality and safety standards. Annual reports are embellished with safety slogans and sustainability statements. Behind the front gates and the glossy annual reports the message is clear: produce or be replaced. Only a few companies go beyond the window dressing and actually endorse, from the top down, continuously improving their safety culture. Those that do embrace safety, show significant performance advantages over their competition that are reflected in their safety, productivity and environmental records and, ultimately their financial statements and share price. Current accounting (and reward) systems make it unlikely financial managers will accept non-conventional approaches to justifying expenditures on safety because they are driven to report “hard” numbers that can be documented and are within the “GAAP or IFRS Rules.” But in reality, accountants quantify soft or intangible costs all the time in their financial statements. Justifying safety investments is greatly enhanced by quantifying what most financial managers would call intangible costs. Government agencies have no problem assigning intangible costs to justify regulations to improve safety. How many times have you heard that the regulation is justified because the cost to industry is X while the benefit to the society is 2 or 3X? How can they say that without including intangible costs? We find it hard to believe these government claims of benefits to society because we have been trained to think about saving hard direct costs to justify investments."

Jan 1, 2017

By Roger E. Melley

Since startup of the Syncrude Canada Ltd. (SCL) oil sands facility in northern Alberta 15 years ago, numerous improvements have been made in the ore conveying system and equipment. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about through the use of detailed field evaluation. Numerous publications are available that detail the various aspects of conveyor technology, and a significant list of papers are presented each year adding to the knowledge in this field. In the area of power formulae in the mid- 1970s, there were two major sources for use in the design of the SCL conveyors: the Conveyor Equipment Manufactures Association Handbook, 1988, and DIN Specifications 22101: Belt Conveyors for Bulk Materials, 1982. These sources were supplemented by the knowledge of the belt and conveyor equipment vendors and from the general literature. The SCL design was based on the CEMA formula. However, it was accepted that this empirical approach had been developed for use with more conventional materials in more reasonable climates. To accommodate

Jan 1, 1993

By D. S. Young

The random variable transformation technique was introduced to make probabilistic structural analysis simple for such structures as slopes, dams, foundations, or retaining walls, where two shear strength parameters are required to analyze their stability by deterministic engineering methods. The Gaussian transformation was performed by using the Hermite orthogonal polynomial function. This transforms the experimental histogram into the standard normal distribution, whose mean is zero with a variance of one. Then, the transformed standard Gaussian variable was used for the bivariate normal probability analysis on the structure. The Gaussian transformation technique and the Hermite polynomial functions were chosen because the bivariate joint normal distribution is well-known and easily available for engineers. The binormal probability analysis was made on the probability region of a certain confidence level by superposing the critical line on the same probability region that divides the region into two zones: stable and unstable zones. The critical line was determined from the back calculation of the deterministic engineering method of the structural design. Finally, the probability of structural failure at a desired confidence level was calculated by simply integrating the volume of the binormal density surface above the unstable zone in the probability region. A simple case of slope analysis is introduced to illustrate this probabilistic approach, and its effectiveness and simplicity is demonstrated.

Jan 1, 1987

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.

By C. M. Bartley

In world-wide mining circles countries become known by the principal minerals they produce. The production of iron, copper, phosphate and sulphur in the United-States-has-been particularly significant and has provided the base for aggressive developments in heavy industry, agriculture and chemicals. Mention diamonds and gold-and you will think--South Africa; silver-Mexico; nickel and asbestos--Canada. The main purpose of this paper is to point out that potash mast be added to the list of minerals by which Canada is known in the mining World. The potash deposits of western Canada must be classed as a major world source of chemical fertilizer raw material. We believe that they are both the largest and the richest of all known deposits in the world. The most knowledgeable people in the industry avoid making estimates of reserves because even where the arithmetic is correct the total is so large that it appears to be ridiculous. In 1957 Marion Goudie made a carefully qualified estimate of 6 billion tons of recoverable potash above 3,500 ft, and grading 25 per cent K20 or better. This figure can now be increased by the amounts available through solution mining. No one has bothered to estimate how much this is because it is so large that the actual amount is not significant.

Jan 1, 1966