Search Documents

By R. E. Musgrove

At the present time Climax Uranium Company recovers vanadium oxide from carnotite type uranium ores in the mill at Grand Junction, Colorado, The flowsheet of this mill is shown in Figure I. Vanadium is solubilized by a salt roast of the slime fraction of the ore and dissolution is accomplished by a water leach. The metal is precipitated from the pregnant liquor as sodium polyvanadate by heating to boiling and adjusting the pH to 3 with sulfuric acid. The sodium polyvanadate, commonly called, "red caken, is filtered, melted, and cast into thin flakes. This fused flaked vanadium oxide is the material which is packaged for sale. Fused vanadium oxide, marketed by Climax, contains approximately 87% V205, 7% alkali oxide, 0.08% sulfur, 0.03% phosphorus, and less than 0.5% Insoluble. This material is of a lower grade and has a higher alkali oxide content than other vanadium products offered for sale at this time. A typical analysis of a high grade vanadium oxide currently offered for sale by another company is 98% V205, 1 - 2% alkali oxide, less than 0.05% sulfur and less than 0.2% Insoluble. The only reagent consumed in the precipitation of the sodium polyvanadate is sulphuric acid. The total reagent cost is 0.58 cents per pound of vanadium oxide produced.

Jan 1, 1958

By Thomas P. Meloy

There is much interest in the automation of entire comminution circuits, At the present technological level it is possible to automate a circuit but to date it has not been done, To successfully automate a circuit, a number of problems must be solved. Not all of them are engineering problems. The purpose of this paper is to discuss some of these problems, as certain the implications of these problems and indicate solutions to them. In this paper the term "automation" is used loosely but in the popular sense. Namely, that a plant is automated if a computer is used to control the basic flow of the materials as well as setting the critical parameters in the process. Specifically, the discussion will concern itself with the control of comminution circuits from the dumping of the ore into the primary crusher until the final interface between the comminution circuit and say, the flotation mill in the case of a sulfide ore.

Jan 1, 1965

By Alten F. Grandt

Surface mining consists of the removal of the geologic strata overlying the coal seam usually with large electric shovels, draglines or bucket wheels. The method produces more or less parallel ridges or peaks of cast overburden, usually called "spoil banks". The mined lands vary widely in their inherent characteristics to produce a vegetative cover and thus can be put to a wide variety of uses. Use is the key to economic and social benefits. Physical and Chemical Characteristics of Soil Material of Surface Mined Lands after surface mining operations, the soil material is a heterogeneous mass whose physical and chemical properties are dominated by the character of the geologic strata overlying the coal. These strata are highly variable in thickness and character. They may include the surface soil, loess, glacial till, sands, shales, slates, limestone and sandstone rock. The method of mining with the several types of mining equipment will also affect the resultant mined area.

Jan 1, 1968

By John J. Simmons

There is considerable interest in the iron and steel industry in the development of technologies that can reduce carbon dioxide emissions, as the iron and steel industry is the third largest producer of carbon emissions in the world, after automobiles and the power generation industry. The E-Iron Iron Nugget Making Process, invented by Dr. Komar Kawatra and Dr. Tim Eisele, provided a major breakthrough in the iron making process as the process uses biomass in the form of hard wood or soft wood as the reductant in the place of coal. Dr. Kawatra recognized that biomass is rich in both carbon monoxide and hydrogen, two important reducing agents. This resulted in initial experiments conducted by Dr. Kawatra and Dr. Eisele in the laboratories of the Chemical Engineering Department of Michigan Technological University (Michigan Tech) that prepared self-reducing pellets with wheat flour as the reductant and limestone/dolomite as the flux. Initial results were encouraging so they extended their work to include hardwood, which is in huge supply in the forests of Michigan and Minnesota, as the reductant. Dr. Kawatra has also applied the E-Iron Technology to other iron bearing minerals to produce pig iron grade iron nuggets. He used the E-Iron Process to convert red mud, a high iron waste product of the aluminum industry, into pig iron nuggets with the rare earth elements reporting to the slag. This work resulted in a patent with Dr. Kawatra and Dr. Michael Archambeau named as the inventors. Dr. Kawatra then extracted the rare earth elements as a separate high value bi-product using oxalic acid, which he produced from carbon dioxide. Dr. Kawatra also conducted a test program that produced pig iron nuggets from New Zealand beach sands. The vanadium in the beach sands was retained in the iron nuggets, recoverable as a valuable bi- product in a separate process. The titanium dioxide in the beach sands reported to the slag. This demonstrates the potential use of the E-Iron Process to convert the large ilmenite reserves in Northern Minnesota into pig iron and titanium dioxide. Another use of the E-Iron Process discovered by Dr. Kawatra was its ability to produce iron nuggets from manganiferous ores. Dr. Kawatra was able to direct the manganese into either the metal or slag by adjusting process temperature. The above discoveries are included in several patents that were assigned to Carbontec Energy. This presentation will only address the use of the E-Iron Process to produce pig iron nuggets from steel mill waste and un-pelletized, mid-grade iron ore. Carbontec Energy Corporation agreed to sponsor additional research directed at improving this new technology that would later be trade named, The E-Iron Process. Carbontec Energy conducted further work that proved that the E-Iron technology could also convert steel mill waste into metallurgically acceptable iron nuggets. Carbontec also collaborated with the Lawrence Livermore National Laboratory and Purdue University Northwest to conduct a Department of Energy (DOE) sponsored program that would use their high performance computer capability to both verify and model the E-Iron Process. Purdue University Northwest reported that the E-Iron Process can produce pig iron nuggets with 85% less carbon emissions than a blast furnace. The E-Iron Process is similar to the ITmK3 process, developed by Kobe Steel, that also produces iron nuggets but uses coal as the reductant.

Feb 1, 2025

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By Peter Zhang, Daniel Su, Mark Alexander Van Dyke, Heather Dougherty, Bo Hyun Kim

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a post-mining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64°, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457-m wide and 3657-m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones in longwall gobs.

Jun 9, 2022

By L. H. E. Weyher

In a previous paper presented at the 1966 Annual Meeting of AIME we reported our work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal.' The initial evaluation based on that work demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper we presented selected test data that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of our data as follows: ? Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity- versus-pressure drop expressions taken from the literature on classification cyclones.

Jan 1, 1968

By E. Wm. Heinrich

Glass sands fall into that extremely select category of mineral deposits that requires a fantastic degree of natural concentration (95% +) of a single component before they can even be considered as ores suitable for further refinement. The combination of geological factors that has produced such an environment of "mineralogical single-mindedness" has appeared only rarely. Factors that require consideration in the economic evaluation of a potential glass-sand deposit can be grouped into three categories: 1) geological (e.g., size, shape, structure); 2) petrographic (e.g., grain size, accessory minerals, nature of iron contaminants); 3) geographic - political (e.g., proximity to consumer, size of market, zoning restrictions). Of particular con ern is the nature of the iron contamination. Iron-bearing species appear as 1) accessory mineral grains, either detrital or authigenic, 2) cements, 3) grain coatings, and 4) quartz-grain inclusions. Selection of the cheapest form of beneficiation requires precise information on the mineralogy of the iron species and their detailed petrography. Because of the antipathetic relationships, in many parts of the United States and Canada between the geographical locations of glass plants and the geological distribution of glass sands, the selection of ac suitable source for a particular glass plant may be dichotomous. One may seek either an exceedingly pure "classic" type glass sand that is relatively distant and whose cost includes a major transportation charge or a relatively proximate and somewhat "impure" source whose cost includes a substantial fee for beneficiation.

Jan 1, 1974

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool has expanded greatly in the last few years. This tool can now be used to produce near surface information which is very useful to geotechnical engineers. Using the lightweight field equipment now available, it is possible to use the radar within mines and tunnels to obtain information which may impact the safety and production of these operations.

Jan 1, 1979

By John R. Riede

Most modern crushing and grinding facilities are automated to some degree. Some, of course, have a very minimum of automatic control whereas others utilize very complex control equipment. However, with very few exceptions, the re has not been a new basic control philosophy applied in this field in the past seven years. The philosophy has been broadened in scope and applied to larger plants, some of them with data logging and so- called computer control, but almost always the same tried and proven basic control philosophy is the basis for the control system. New types of control devices to better implement the automatic control have been developed and are continuing to be developed. These devices and their application will be explained and the advantages and disadvantages of each will be discussed. Automatic lubrication of plant equipment is most essential, but this paper will not cover these systems. The use of data logging and computer analysis of the data obtained is fairly recent and it is hoped that by careful analysis of this information that new and better basic control philosophy will be forthcoming. This paper will describe the basic philosophy applied in its simplest form to several types of crushing and grinding equipment, and it will describe how it is being expanded to more complex systems. Some of the economics with regard to first cost, return on investment and maintenance will be covered.

Jan 1, 1965

"The National Mining Hall of Fame and Museum (NMHFM) announced the 2018 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exploration, extraction, management, education and research and development in the U.S. mining industry. Their contributions have had significant and lasting impacts on the mineral and mining industry; these individuals were selected for being mavericks, thought leaders, researchers, educators, mentors, wealth builders and philanthropists.Professor John M. Guilbert, Dr. Leo J. Miller, Robert E. (Bob) Murray and Douglas (Doug) B. Silver will join 240 other mining industry luminaries when formally inducted into the National Mining Hall of Fame on Sept. 29, 2018. Additionally, the Prazen Living Legend of Mining Award will be presented to the Freeport- McMoRan Foundation. The 31st Annual Induction Banquet and Ceremony will be held at the Ritz-Carlton in Denver, CO.2018 National Mining Hall of Fame inducteesProfessor John M. Guilbert was a renowned geologist and professor of economic geology at the University of Arizona; he had a distinguished 50-plus year career in academia and business. Guilbert, together with J. David Lowell, worked on the most important breakthrough in mineral exploration in the last 100 years, the Porphyry Copper Model. This work, known as the Lowell and Guilbert Model, was utilized by exploration geologists worldwide over the next four decades to discover hundreds of millions of tons of copper metal and numerous profitable mines including the prosperous Bajo de la Alumbrera copper mine in Argentina. Guilbert was a founder of The World Museum of Mining in Butte, MT. He was the recipient of countless awards including the Society of Economic Geologists (SEG) R.A.F. Penrose Medal as well as the D.C. Jackling Award from the SME.Dr. Leo J. Miller was a maverick in the mining industry and no armchair geologist. He believed that active fieldwork, on foot with a rock pick, was indispensable for exploration. His basic tenet was to absorb as much information about an exploration target up front, formulate ideas – sometimes novel ones — and then get out into the field to prove those ideas. Miller was known to diverge from the standard interpretation of the geological processes, which formed the mineral deposits, and to apply innovative applications of high-tech tools to more usual exploration programs. This approach resulted in a 50-plus year career that included the discovery of the Kidd Creek massive sulfide deposit and the development of the Lee Creek phosphate deposit; which other explorers had previously given up on, believing whatever phosphate might be present would be too difficult and expensive to mine. The recipient of many honors and awards, Miller received the SME Robert M. Dreyer award in recognition of outstanding achievement in ore discoveries."

Jan 8, 2018

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024

By J. A. MacLellan

It is the hope of the author that this paper, largely a compilation of observations and opinions built up over 20 years of experience in cold and remote areas may be of some help to others in designing better plants for the future in the north. The north is not as difficult to operate in as the better story tellers make it appear to be. ()n the other hand for 6 months of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut a multi-million dollar plant down at -4n' F with a 4n M.P.H, wind. It only takes one man door improperly latched to freeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later while you are having Christmas dinner, a watchman will call up to report that the whole plant is flooded because the main water line just froze up and burst. Basic things to remember in plant design for cold and remote areas are: everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore he kept to an acceptable minimum. Service areas on the other hand must he adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles for instance have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50° F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze up. People in a remote area are expensive. The capital investment per employee may be as high as $30,000; with fringe benefits per annum costs of an employee will he as high as 812,000 per year regardless of basic wage rate. It

Jan 1, 1971

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022

By Thomas R. Doyle

When you think of the state of Maine, you probably think of lobsters or lighthouses. The last thing you would think of is metallic mineral mining, and that is for good reason. According to the Maine Geological Survey?s website, ?no metals have been mined in Maine since 1977.? Moreover, Maine?s metallic mineral mining laws and rules, which were last rewritten in 1991, have effectively made mining in the Pine Tree State impossible. Statutory changes enacted in 2012, however, put Maine on a path to make metallic mineral mining part of the local economy in the near future. History of metallic mineral mining in Maine Currently, Maine is not a metallic mineral mining state, though that has not always been the case. The 1800s saw various mining operations in Maine, including what the Maine Geological Survey calls a ?mining boom? from 1879 to 1882, where mining of iron, silver, copper, lead and zinc expanded rapidly. Mining and mining activity in the more recent past, however, drove the debate before the state legislature when this issue was debated in 2012.

Jan 1, 2012

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987