Search Documents

By Paul Madsen, Bade Sozer, Thomas Hennings, Eileen Test

The Rondout Bypass Tunnel in New York has two access shafts. The upper sections of the shafts are lined with steel pipe to resist a substantial net internal water head . Initial design included a ¾-inch-thick cement mortar lining (CML) for all three components. Because of concerns with CML application on large-diameter pipes, the protective lining was redesigned for shotcrete application. This paper discusses the details of that design, mock-ups, and shotcrete application.

Jun 13, 2023

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Richard F. Roethe

Surface coal mining productivity in the U.S. and Illinois has shown a general declining trend since 1969. The U.S. Department of Energy conducted an analysis in 1980 of the causes of declining productivity in different states. This paper presents a detailed analysis of changes in overall productivity and productivity in different functions such as overburden preparation, overburden stripping, reclamation, coal handling, etc. during the period 1970-1982. Statistical analysys techniques including multiple regression were utilized in the study.

Jan 1, 1983

By Jerry M. Riggsbee, John H. Weber

INTRODUCTION The Washington Metro is a 98 mile rapid transit system that will serve the District of Columbia, southern Maryland, and northern Virginia. The construction work herein described relates to Section B-1 of this system. The contract for this work was awarded by the Owner, The Washington Metropolitan Area Transit Authority, to a joint venture doing business under the name of Ball-Shea-Norair. The partners in this venture were Gordon H. Ball, Inc., Danville, California; J. F. Shea Company, Inc., Walnut Creek, California; and Norair Engineering Corporation, Washington, D. C. The bid price for the project was $33,741,524 with a contract duration of 910 calendar days. Notice to proceed was issued January 5, 1970. The present modified price for the work is $36,866,000 with completion anticipated in July 1974. (About 1,638 days elapsed time.) The work to be done consisted essentially of construction of 3,490 linear feet of cut-and-cover track with side platform, and 600 ft cut-and-cover arch shaped subway stations. Stations are located in Judiciary Square and Eighth & G Street, N. W., areas. Decking of excavation in street areas, maintenance of traffic and utilities, vent and fan shafts, underpinning of court buildings in Judiciary Square and the Smithsonian National Portrait Building, and an electrical substation were included in the contract. Stations were constructed of cast-in-place concrete.

Jan 1, 1974

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written which aid in the design process in the academic arena and should also have industrial applications. The programs described include a dragline cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program and an overburden volume and coal tonnage sequencing program.

Jan 1, 1985

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981

By Benoit Gagnon

Mining of the Schefferville iron deposits began in 1954 on completion of the 574 km railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at Schefferville to develop a process for upgrading the extensive lower grade deposits containing 5l% iron with 15% silica (natural analysis). Engineering for 6.1 million tons per year Beneficiation Plant using cationic silica flotation and the A-C Grate kiln began in 1970 and the first pellets were produced in mid 1973. Production requirements and operating difficulties have restricted capacity to approximately 85% of design but ongoing improvements are being made continuously to attain design capacity.

Jan 1, 1980

By H. E. Rutherford

Monterey Coal Company has begun a geologic monitoring program in order to better understand our in-mine geologic conditions and to apply the knowledge gained to our mining operations. Two methods are used to collect information. The first is a monthly examination of conditions throughout the mine using a rapid mapping technique. The second is the detailed mapping of specific events encountered during mining such as faults and roof falls. The data gathered from both methods is correlated with operational statistics to create a geologic/production database. From the database, a monthly evaluation of mining conditions is made. Also, the database has proved useful in such areas as forecasting roof conditions and examining how faulting has affected mining operations.

Jan 1, 1984

By Richard J. Goff

Technical Support, one of several major organizational units in the Mine Safety and Health Administration, provides technical assistance to the mining community in all areas of health and safety. One of its many areas of expertise is noise control. Depending upon the needs of the operator or inspector, the services provided can range from locating major noise sources to actually building noise controls. Over the years a vast amount of knowledge has been obtained as to what will work and what will not. DESIGN GOALS While many noise controls have been developed for mining equipment and operations, the most acceptable (ergo successful) have achieved the following design goals: - a noise level reduction of at least 5 decibels; - minimum interference with production; - inexpensive to install; and - effective in reducing low frequency noise.

Jan 1, 1984

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022

Unplanned ore dilution can have severe impact on the economics of a mining operation. The paper discusses and distinguishes between controllable and natural parameters influencing ore dilution, and how it can be minimized in longitudinal mining systems of narrow vein orebodies. It is shown through data of surveyed stope profiles and numerical modelling that unplanned ore dilution is a function of stope design and construction, orebody geometry, and rock mass characteristics.

Jan 1, 2010

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. Standards are available across multiple industries that prescribe emission limits and test methods for electronic devices. A literature review was conducted in this study, and an overview of EMI standards in other industries is provided. Also, an example of how a standard can be applied to mining equipment is presented.

Nov 1, 2022

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986

By Robert E. Frey

Regardless of the mechanical design features of a particular air classifier certain basic principles apply. Specifically , there are two forces at work: 1. An air drag force 2. An inertial or centrifugal force. The air drag force has an increasing influence as particles become smaller. A very small low mass particle is easily carried along with an air stream even when turning a corner. Thus, fine particles follow the air away from the classifying zone. Inertial forces increase as the mass of a particle gets larger. Thus oversize particles tend to obey Newton's laws and respond to centrifugal forces or simply continue in a straight path when the airflow changes direction.

Jan 1, 1985

By B. C. Darst

Intensive efforts to develop potash use in agricultural production were begun in the US 50 years ago. Early growth was rapid and continued well into the 1960s. Many soils were inherently low in K, so crop responses to fertilization were often dramatic. Deficiency symptoms were common. Per-acre use has continued to increase in recent years, but annual growth rates have slowed. Soil buildup has occurred in some areas. Poor economics in the 1980s have been difficult to overcome. Efforts are now well under way to develop potential markets around the world.

Jan 1, 1987

By B. K. Cantrell, K. L. Rubow

The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8- µm aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 µm diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.

Jan 1, 1992