Search Documents

"Iron ore is the source of primary iron for the world’s iron and steel industries. Its production can be reported as crude ore, usable ore or iron content of ore. Historically, the U.S. Geological Survey (USGS) used reported crude ore production from China in tabulations of world iron ore production while other countries have typically reported their production in terms of usable iron ore. When China’s crude ore production was tabulated with usable ore production from other countries, world iron ore production totals have been overestimated by 10 percent to a high of content and may include products such as concentrates, direct-shipping ore, pellets, and sinter.• Iron content, also referred to as metal content or grade, denotes the amount of elemental iron in the crude or usable ore.BackgroundIron ores consumed in the steel industry typically require an iron content greater than 58 percent before being considered commercially usable. Iron ores that are not commercially usable must undergo beneficiation to raise the iron content. Approximately 98 percent of the world’s usable iron ore production is consumed in blast furnaces to make pig iron, which is further processed to make steel.High-grade iron ore mines can supply usable iron ore, known as direct-shipping ore, to blast furnaces, with minimal physical processing and no beneficiation. With direct-shipping ore, the reported production for crude ore and usable ore are the same. Ore from low-grade deposits must undergo beneficiation to increase the iron content before it can be used by the steel industry. In this instance, the mined material is called crude ore and post-beneficiation concentrates are called usable ore; the amount produced will be less than the crude ore amount. With the notable exceptions of countries such as Australia and Brazil, most of the world’s iron ore deposits are low-grade and require beneficiation."

Feb 1, 2017

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

"In this review, the sintering process is first described and analyzed to identify the key factors affecting the structure and quality of iron ore sinter. Under fixed sintering conditions, the granulation efficiency, nucleus stability and primary sinter melt volume and properties of the iron ore are considered to have significant influence on the sinter structure and quality. Discussion is then focused on the effects of the chemical, physical and mineralogical characteristics of the iron ore on these key factors, and the consequences for sinter quality.IntroductionSintering is the most economic and widely used agglomeration process to prepare iron ore fines for blastfurnace use. In modern blast furnaces, particularly in East Asia, iron ore sinter typically constitutes more than 70% of blast-furnace ferrous feed. High sinter quality and efficient sinter production are thus required both to withstand extreme operating conditions and maintain the productivity of modern blast furnaces. At the same time, due to the increasing depletion of high-grade iron ore resources from large deposits, iron ore producers are moving toward developing an increasing number of deposits of much smaller sizes to maintain current production levels. It is therefore imperative for iron ore producers to develop long-term strategies to maintain the quality and consistency of the iron ore fines they are producing while exploiting these smaller, complex deposits. The iron grade, gangue minerals present, overall mineralogy as well as physical characteristics of iron ore fines being mined from these different deposits vary considerably. Overall, ores now have highly complex mineralogy, are becoming more porous and friable, and contain increasing amounts of gangue minerals, which will have important implications for the sintering process and sinter quality.Blending is one of the most effective options being explored by iron ore producers to deal with multiple small complex deposits. This allows the iron ore producers to reduce the number of products and take full advantage of the unique characteristics of each individual deposit to achieve long-term product consistency while increasing production. Blending is also a common practice in sinter plants as it is almost impossible to produce from one single ore a high-performance sinter mixture with the required processing characteristics. A typical sinter mixture used in Japanese steel mills (Nakano and Okazaki, 2007; Matsumura et al., 2013) often contains five or more ores to achieve balanced sinter quality and productivity with relatively low cost of raw materials."

Jan 1, 2015

By Paul S. Parobeck, Robert A. Haney, Andrew J. Gero, Thomas F. Tomb

As a result of recommendations made in the 1988 Report of the Mine Safety and Health Administration Advisory Committee on Standards and Regulations for Diesel-Powered Equipment in Underground Coal Mines, the Mine Safety and Health Administration (MSHA) initiated a program to develop and test a diesel particulate sampling device. The sampling device employed the principles of inertial impaction to separate respirable dust into two fractions; one fraction containing particulate material having an aerodynamic equivalent diameter equal to, or greater than, 1.0 micrometer, and the other fraction containing particulate material having an aerodynamic equivalent diameter less than 1.0 micrometer. The design criteria were based on data which showed that virtually all of the diesel particulate material and very little of the mine generated dust was less than 1.0 micrometer in size. The instrument was tested in underground dieselized coal mines and in the laboratory. Comparative measurements were obtained with the MSHA designed impactor sampler, a University of Minnesota (UM) designed impactor sampler and MSHA's standard respirable coal mine dust sampler. Simultaneous measurements were also obtained with five of the MSHA and five of the UM designed impactor samplers to investigate between sampler precision. The paper discusses the design differences between the MSHA and UM impactor samplers, the precision of replicate measurement obtained with both instruments and compares measurements obtained with the respective samplers of the sub- and supermicron fractions of the respirable material.

Jan 1, 1991

By Wayne S. Cavender

The geochemical association of arsenic and gold in epithermal precious metal deposits of the Basin and Range province is well documented, and in this paper I wish to discuss the evaluation and utilization of this element association for geochemical gold exploration. In 1961-62, I conducted an exploration program on lands controlled by Getchell Mine, Inc, and centered about the Getchell gold mine itself, Besides exploring for new gold deposits, the program was to evaluate these lands for potential deposits of any type; thus, a multi-phase program encompassing a number of exploration methods was conducted. I shall not elaborate on the process of designing the program or of integrating the various methods, but for gold exploration, geochemical methods were determined to have the best potential. This paper is based on that effort. Figure 1 shows the exploration area, which covers the northern half of the Osgood Mountains in eastern Humboldt County, Nevada. The Getchell $line is on the east flank of the range and is about 40 miles northeast of Winnemucca.

Jan 1, 1964

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.'s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By P. G. Irwin

Natural resins, those derived from coal and those mined in the Uintah basin, face challenges from synthetic resins that are derived from petroleum sources and rosin or wood sources. In the past, fossil resins from coal were produced by various companies, the last one being Hercules, Inc., which sold BLACKHAWK resin until a fire destroyed the plant in the mid 1970's. Approximately four to fjve million pounds of BLACKHAWK were produced and sold mostly to the printing ink industry. Uintaite, more commonly known as Gilsonite® resin, was widely used by various industries, notably in printing inks, coatings, stains, adhesives, foundry, asphalt paving, and oil well drilling muds. Gilsonite has lost market share over the last thirty years to various synthetic resins particularly hydrocarbon resins that are derived from petroleum sources.

Jan 1, 1990

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historical Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon in leach for recovery of gold ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a course rock fraction from the grinding circuit SAG mill. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900s. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1983

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Michael L. Maniocha

Most magnesia (MgO), whether of natural or synthetic origin, is used in the dead-burned or periclase form as refractory linings for the production of steel. Continued research in refractory science, combined with good refractory maintenance and improvements in steel-making processes, have resulted in decreased use of magnesia. To make up for this loss of business, producers of synthetic magnesia have started to manufacture a variety of magnesium-based chemicals that are used in many industries. There are three primary methods of producing MgO. The first involves the calcination of naturally occurring minerals species. Most of the magnesia produced by this method uses the rhombohedra1 carbonate mineral magnesite, MgCO,. To a lesser extent, the mineral brucite, Mg(OH), is calcined to magnesia. Magnesia produced by the calcination of minerals is called natural magnesia. The second production method uses magnesium-rich brines, or sea water reacting with lime or calcined dolomite to produce magnesium hydroxide. The magnesium hydroxide is subsequently calcined to magnesia. Material produced in this way is called synthetic magnesia. The third major method of production uses saline lake brines to produce magnesium chloride. Magnesium chloride brine is sprayed into a reactor where it thermally decomposes into MgO and HCl. The magnesia is purified by slaking to magnesium hydroxide followed by calcination. Magnesia produced in this manner is also know as synthetic magnesia (Duncan and McKracken, 1994). The degree to which the magnesium minerals or the synthetically prepared magnesium hydroxide is calcined governs the physical properties of the resulting MgO. It is the physical properties that dictate the end use for the product. The terms used to describe magnesia vary along with the degree of calcination. Table 1 summarizes the terminology used when discussing the various forms of magnesium oxide.

Jan 1, 1997

By S. Bhamidipati

Abstract. Controlled flow is an aspect often desired in mine ventilation. This is normally obtained by using fans and regulators to achieve the required pressure balance in the system. Preference for a certain network layout of these control devices is influenced by technical as well as legal and economic factors. In this study, a model is developed based on an economic criterion by which an optimum layout of fans and regulators for a controlled flow system can be determined. The concept is analo¬gous to the critical path crashing. However, a linear programming package is used to demonstrate the solution procedure for a hypothetical venti¬lation network.

Jan 1, 1983

By D. Malhotra

The effect of some of the reagents, namely hydrocarbon oil, Syntex (sulfated coconut oil surfactant), pine oil, sodium silicate, and lime, used at the Climax mill on the recovery and grade of molybdenite and gangue minerals has been investigated experimentally using factorially designed test approach in the laboratory. The results of the investigation are presented in two dimensional plots. The lower additions of lime (equivalent to a pH of 8 to 8.5) were desirable for maximizing recovery subject to constraints on grade. Higher additions of pine oil improved recovery, but only at the expense of grade. A mathematical model of the objectives of an operating plant was formulated and optimum reagent conditions obtained.

Jan 1, 1977

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Z. T. Bieniawski

Engineering rock mass classifications have received prominent attention as design aids in rock tunneling. Support selection in civil engineering tunnels and chambers is often based on such classifications. In the field of mining, rock mass classifications have not been utilized to the same extent but some applications have been made. This paper considers the current rock mass classification schemes from the point of view of their potential in mining. Case histories are described featuring their use in assessing the cavability of ore as well as entry stability and support. Current possibilities for rock mass classifications as design aids in mining are outlined.

Jan 1, 1980