Search Documents

By C. A. F. Pinto

In the present work compared flotation kinetics of apatite with four different collectors was established. Sodium oleate and rice bra~ oil were used to represent conventional collectors. The new collectors included a sulfosuccinate and a sulfosuccinamate. It was observed that the collection ability of each reagent was very dependent upon the mineral size ranges. The results-were analyzed in terms of size-by-size recovery curves. Flotation rates were also very dependent on size ranges of the mineral particles. One of the new collectors displayed higher flotation rates for coarser particles than the other reagents tested. Synergetic effects were also apparent when a conventional collector was mixed to a new collector.

Jan 1, 1991

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By Eduardo Velasco, Paz Navarro, Alfonso Navarro, Claudio Cimiotti, Alejandro Sanz, Nick Karlin

The LA Effluent Outfall tunnel is a 7-mile long, 18' internal diameter, secondary treated effluent discharge tunnel currently under construction by Dragados USA for the Los Angeles County Sanitation District No. 2 (LACSD). The purpose of this tunnel is to add redundancy and increased capacity for discharge of secondary treated effluent from the LACSD’s Joint Water Pollution Control Plant, located in Wilmington, California within Southern Los Angeles County. Current discharge from this facility flows through two existing tunnels of 8' and 12' horseshoe profile, constructed in 1937 and 1958, respectively. When the new tunnel is complete, it will add an additional capacity of 670MGD in peak wet weather flow conditions. Geology of the roughly 7 mile long tunnel was divided into six reaches by the contract documents. Tunnel Reaches (TR) 1 to 3, comprising 19,550' will be excavated in alluvial sands of the San Pedro and Lakewood formations, with cover ranging from 45 to 90 feet. In this reach the tunnel intersects the seismically active Palos Verdes fault Zone. TR 4 is a 1,600' transitional zone between alluvium and the rock formations of the Palos Verdes (PV) Hills, comprised mostly of Malaga Mudstone. TR’s 5 and 6 total 15,591', and are within the rock formations of the PV Hills with overburden ranging from 315' to 475'. The primary constituent of the PV Hills is Altamira

Jun 13, 2021

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By M. P. D. Ingunza, Júnior Santos, F. S. D. Araújo, A. L. C. Araújo, J. Y. P. Leite

Wastewater sludge is a problem for environmental control and it is necessary alternative researches for its reuse. Industries can research the association of clay and sewage sludge as a source of ceramic mass. This procedure can contribute for the industry sustainability including in its raw materials, wastes of environmental concern. This paper presents the results of sewage sludge and clays characterization being analyzed particle size distribution (sedimentation), mineralogical (X-ray diffraction), chemical composition (X-ray fluorescence), thermal analysis, density, and Atterberg proprieties (liquid and plastic limit; plasticity index) and also their applications in ceramics. Results were used to determine moisture for mass of raw material and sewage sludge and there were realized tests of fired in kiln at temperatures used in ceramic industry for bricks production. In the test pieces were analyzed the properties for application as bricks.

Jan 1, 2005

By Gerald C. Smith

Carlin Gold Mining Company is a wholly owned subsidiary of Newmont Mining Corporation and is located 76 kilometers north west of Elko, Nevada. Multiple bench open pit mining methods are being used to mine 24.5 Mt of ore and waste per year. Mining started in 1964 and up through 1983 Carlin has mined 138 Mt of ore and waste and has milled 13.8 Mt of ore. Selective mining of carbonaceous and oxide ores together with a good grade control program have been key factors in the success of the operation. This paper will present the raining methods and the mining equipment being utilized to make Carlin Gold Mining Company a very profitable operation while mining and milling low-grade gold ore.

Jan 1, 1985

By Nikolaos Syrtariotis, Mark Berger, Timothy O’Brien, Vojtech Gall

The Northeast Corridor Superconducting Maglev Project (SCMAGLEV) entails construction of a high-speed train system between Washington, DC and New York City, with the first leg between Washington and Baltimore, MD. This innovative project will shorten travel times between Washington DC and Baltimore to approximately 15 minutes, and connect Washington, DC to New York City in under an hour. In 2021 the draft EIS is expected to be issued for comment with a Final EIS/ROD anticipated by early 2022. This paper provides an update on the project as presented in Gall et al. (2020) and discusses the economic and environmental benefits, preferred alignment alternative, preliminary staging and launching of the TBMs for construction, and preliminary station design.

Jun 13, 2021

By David J. Hatem, K. Bhattarai

The increasing popularity of alternative methods in delivery of underground infrastructure projects has given rise to innovative and collaborative contracting strategies to allocate and manage the unique risks associated with the work. This paper presents approaches and recent examples of how risk has been dealt with using various alternative delivery methods, including Progressive Design Build (PDB) and Construction Manager/General Contractor (CM/GC). Based on the experience gained from these examples, recommendations for an innovative and collaborative risk baselining approach using contingency sharing are presented that should advance the overall goals of equitable risk sharing and compensation.

Jun 13, 2023

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982

By Raj K. Rajamani, Samira Rashidi

Wear is an extremely important topic when considering high-pressure grinding rolls (HPGR) for any new application. Given the inevitable variations in ore properties throughout a mine’s life, it is difficult to predict the effect of material and operating conditions on the wear parts: specifically, the HPGR rolls. However, the possibility of continuous scanning of rolls provides ample information to review the wear pattern and ways to optimize it. In this regard, as part of a broader investigation, the feasibility of in-line scanning of HPGR rolls in a laboratory-scale HPGR is studied and presented. The choice of scanners and methods adopted to achieve high-level accuracy for determining wear is discussed in this paper, and the inherent variability affecting the measurements is evaluated. 

By Patrick M. Hurley

The spreading-ridge, or accreting plate margin, is the primary conduit of metals delivered to the earth's surface. Isotope ratios of lead show primitive mantle values at these sites, indicating that this is true. We can use lead isotopes in any mineral deposit to indicate the degree to which the metal is "primitive" in the sense of having been uncontaminated with U-enriched crust or "crustal" in the sense that it has been cycling at the earth's surface since earlier times. The reason for this is that the upper continental crust has an enrichment in the ratio of U/Pb over that in the mantle, so that old continental leads have a larger radiogenic component. The primitive metals delivered to the surface at the spreading-ridge are transported on the oceanic plate until they reach a subduction zone. Here they become cycled in the "orogen". However, in this process the primitive metals are mixed with metals from the continent so that the average lead isotope ratios are between those in the mantle and the average upper continental crust. Subsequently a part of the metals in the orogen may become fixed in a new block of continent. However there are processes which continue to uplift and erode ancient continental regions so that there is a continuous feeding back of metals to the orogen. We have therefore a cycling of metals from the existing continental crust into the orogen where they are mixed with new contributions from the spreading ridge and mantle.

Jan 1, 1977

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By Eugene C. Spilker

Cross country belt conveyors are becoming the preferred method of bulk material handling in the industrial complex. Installed cost, maintenance, reliability, simplicity and operating expense enhance this choice, especially when faced with rising cost and questionable availability of liquid fuels. Conveyor flights are getting longer, faster, and higher in capacity, and are being installed in rugged terrain. Rights of way are often difficult to obtain. All these considerations lead up to design aspects well beyond those for in-plant conveyors. This paper points out some of the aspects that lead to the successful design of a cross country belt conveyor system.

Jan 1, 1980

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

By Jodie Robertson, Isabel Barton, Cristian Caro

Prior to mining, all rocks contained in a mineral deposit must be placed in one of several categories known as ore types. Each ore type describes a different way that the rock will behave in processing. The ore type determines which process stream a particular mined unit will be sent to, sets expectations for process engineers and metallurgists, and forms the basis for recovery predictions and production estimates. At first, ore types are assigned mainly by geologists based on visible geological criteria (dominant ore mineralogy, estimated grade, rock type, alteration type). As metallurgical tests are carried out and process data accumulate, the resulting criteria may be factored into the ore typing process, typically as assays and recoverable metal using the relevant process(es). Other variables may also be incorporated into ore typing at operations if they are particularly important, such as grindability, preg-robbing, gangue reagent consumption, and the presence of especially deleterious minerals such as talc or smectite. The mine operation department may also redefine ore types and/or process destinations based on economic criteria. A “best” ore type is designated that (in theory) best describes how the rock will behave in processing. Codes representing this ore type are entered into the drill hole database, then interpreted on cross sections and level plans, and finally added to the block model. Ore types are iteratively reexamined and adjusted over the life of a project. Major difficulties in effective ore typing are (1) lack of communication between geologists and metallurgists, (2) the imprecision inherent in imposing clean categories on messy natural systems without discrete divisions, (3) the need for ore types to provide useful information for a wide range of processes, (4) difficulties in scaling up laboratory test results to mine production, and (5) conflict among geological, metallurgical, and economic criteria for ore typing.

Nov 8, 2023

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991