Search Documents

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By Edward F. Nagle

Instrumentation engineers have recently devised practical methods of metering the net solids flowing in a hydraulic mixture. The solids flow rate is determined by measuring the specific gravity and the flow rate of the mixture. T e specific gravity is measured by a variation of the bubbler system. The flow measurement is made by a somewhat unorthodox orifice requiring field calibrations. The linear mixture flow signal is then multiplied by the specific gravity signal, which is directly proportional to the percentage of solids in the mixture, to produce a linear solids Slow rate signal. The computations in this system are performed by Sorteberg pneumatic relays. Having obtained this measurement, integration and automatic control of hydraulic solids flow are available. This system is useful in mining, drilling and dredging industries. It provides maintenance of the net solids flow rate and reduces power consumption. Automatic control will provide rapid stabilization of net solids flow rate and release operators from making menual adjustments. The advantages of this application are economy of operation and increased pump efficiency, This paper describes a hydraulic solids flowmeter system installed aboard a dredge. Its purpose is twofolds:- 1. 20 provide a summation of the net solids flowing 2. To make available a practical guide for the drag tender operator. (Dwg. GSD-2219)

Jan 1, 1958

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By D. G. Krige

I read the paper “The jackknife approach” with interest. There appears to be a widespread misunderstanding of the kriging variance as a measure of the error variance of the kriged grade estimate of an ore block. Virtually all mineral deposits display skew frequency distributions and are subject to the well-known proportional effect. Thus, it is usual to find in an ore body, when subdivided a really into subpopulations, that the variances of the grades (or the total sills of the variograms) for the subpopulations will be correlated with the corresponding mean grades (usually linearly with the squares of the mean grades). Thus, the variogram will be stationary.

Jan 1, 1996

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971

By J. Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world´s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards de-carbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain or Germany are only forerunners of this development - their centuries of coal production have been finished. The concept of Sustainable Development (SD) is fundamentally based on a model of progress where ecological, economic and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as: How can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry´s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later. INTRODUCTION Principally, mining natural resources is a finite business that reaches its limits once the deposits mined are depleted, the resources can no longer be mined in an economically profitable way, or substitutes are pushing the mined products out of the market. An example for the latter is the increasing replacement of coal with natural gas and renewables in power generation in the USA. (Kok 2017) According to the model of the product lifecycle, the global mining hard coal mining industry has reached the stagnation phase. (Kretschmann 2000) Although the coal mining business is more a multi-regional than a global business the trend is obvious. The peak of coal use is behind us, especially because the coal demand of China is slowly decreasing since 2013. (Shell 2018) China´s government has announced investing $360 billion in renewable energy by 2020 and scrap plans to build 85 coal-fired power plants. In March 2018, Chinese authorities reported that the country was already exceeding official targets for energy efficiency, carbon intensity, and the share of clean energy sources. China’s energy regulator, the National Energy Administration, rolled out new measures to reduce the country’s dependence on coal. (Kejun and Woetzel 2017) Coal consumption in the US is facing a 16 % decline in five years from 800 to 670 million short tons between 2015 and 2019 and - according to the EIA – will not rise again. (EIA 2018) The decline is attributed to complex market dynamics from low gas prices because of the “shale gas revolution” (Kok 2017, p. 3) to federal environmental regulation like the Clean Power Plan. The United Nations´ UNEP Finance Initiative is cooperating with the Portfolio Decarbonization Coalition of institutional investors to implement decarbonization strategies across their portfolio. Amongst these investors is the New York State Common Retirement Fund, the third largest public pension plan in the USA. (UNEP 2017) The European Union has already begun to de-scribe pathways to decarbonization. (European Union 2018) The Norwegian sovereign wealth fund, the world´s largest, excluded coal-related companies for ethical reasons. The oil giants Total S.A. and Royal Dutch Shell, tradi

Jan 1, 2019

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By Per-Martin Sandgren

LKAB's ores have specific mineralogical properties that make them especially suitable for the production of super-grade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. Until 1978 the approximate assay was 71.2 % Fe and 0.45 % SiO2. Since then the assays have been improved by process modifications to approximately 71.5 % Fe and 0.20 % SiO2. Scope exists for still further improvement. In recent years the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.6 % Fe and 0.30 % SiO2. Other special products are under discussion. The Malmberget ores are also suitable for the production of high-purity direct reduction pellets with a SiO2 content below 1 %.

Jan 1, 1981

By J. R. Walls

The United States potash industry had its beginning in the early Colonial days. Potash was initially manufactured by leaching of hardwood ashes in large iron pots. Production of potash was recorded as early as 1631 in New Hampshire, and in Maine a few years later. According to the census of 1850, the production of potash was America's most thriving chemical industry and, at that time, 569 plants were reported producing potash from wood ashes. Interest in potash was so great prior to the 1800's that the very first United States patent, signed by George Washing- ton, was granted for the production of potash on July 31, 1790. A new era for the production of potash began when potash was discovered by the analysis from a brine well in 1839 near Stassfurt, Germany while exploring for salt. The predominant use of potash at that time was in the chemical industry rather than agriculture. The discovery, by Justice von Liebig in about 1858, that potash salt contributed greatly to the essential plant food in soil opened up an enormous potential market for a suitable potash material.

Jan 1, 1985

By P. Somasundaran, J. T. Kunjappu

Spectroscopic techniques are becoming increasingly popular for characterizing the interior of adsorbed layers of surfactants and polymers at solid- liquid interface as well as in the identification of com- pounds on mineral surfaces. This review encompasses the application of fluorescence and ESR spectroscopic techniques to reveal the microscopic environment of the adsorbed layers of surfactants and polymers on minerals with a special reference to the adsorption of anionic surfactants (e.g., sodium dodecyl sulfate) and polyelectrolytes (e.g., polyacrylic acid) at positively charged mineral (e.g., alumina) - water interfaces. Finally, the utility of XPS and auger techniques to identify the surface elemental composition of different mineral species has been related to their flotation efficiency.

Jan 1, 1987

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Patrick B. Kenny

Generally speaking, it is safe to address this conference as a conclave of Engineers, Owners' Agents, Governmental Representatives, and Contractors. As a group, we have assembled here to learn of our compatriots engaged in similiar underground operations throughout the United States and the World. We are here to learn of improved methods, higher technology, and better management. Through the acquisition of this knowledge, we each hope we can improve our own particular services, products and projects. This session is dedicated to a discussion of "Costs". The most apparent reason for a discussion of costs at this level is to expose subjects affecting costs and propose methods to reduce them. From that premise a contractor can identify three areas of discussion: design considerations, contract considerations, and governmental considerations. A fourth area of consideration is an introspective view of the contractor's role in the design construct process. Unnecessary costs and risks attributable to these areas are contributing excessively to ever increasing project and system costs. DESIGN CONSIDERATIONS On April 20, 1977 the Metropolitan Sanitary District of Greater Chicago accepted proposals for the Tunnel and Reservoir Plan on Contract A and Contract B. This letting called for construction of over 33 km (21 miles) of the Mainstream Tunnel bored at 9.75 m (32 ft) to 10.67 m (35 ft.) in diameter. Also included were all the appurtenant collecting and regulating structures. The proposal allowed the

Jan 1, 1979

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

By Gerard P. Hand

The use of graphite in industrial applications is one of the oldest in the world. Yet, it is one of the fastest-changing technologies today. Graphite was first used centuries ago in developing writing instruments and as a raw material in crucibles used in melting metal. Today, graphite is used in some of our most demanding industries. These include aerospace, electronics and automotive applications. Graphite usage has historically been split between the natural and synthetic forms. Figure 1 shows the breakdown of natural graphites and synthetic graphites used. The usage of natural graphites and synthetic graphites is split fairly evenly, although the applications are quite different. Figure 2 shows the breakdown of applications using natural graphite. The largest application is the refractory industry. This includes refractory brick and plastics, crucibles, shrouds and other refractory parts. This main application uses roughly 50% of all natural graphite. The refractory industry is an important application for natural graphite. However, the refractory markets have been struggling for several years. As demonstrated in Fig. 3 (Semler, 1996), the production of refractories in tons per year has declined by more than 32% during the last 25 years. Refractory prices have actually risen on a dollar per ton basis during that same period as the product mix has shifted to the value-added side. Raw material and production cost increases, inflation and other related costs have kept profitability at low levels for the industry. Furnace linings that once lasted 1,000-2,000 heats now last 8,000-12,000 heats. This means that tonnage requirements have gone down and quality requirements have gone up for graphite suppliers. Therefore, new opportunities and applications must be developed if the graphite industry is to grow. Synthetics are the other major forms of graphite. There are two forms of synthetic material currently used. One is the traditional type. It is made from the turnings of graphite electrode production. The second was developed in the mid-1970s in response to a shortage of conventional synthetic graphite. This occurred by a breakthrough in thermal technology. This new technology purifies, desulfurizes and graphitizes petroleum coke on a continuous basis at temperatures of more than 2,500° C (4,532° F). This product is called desulfurized petroleum coke (Desulco). It now accounts for about half of the synthetic type material used in the United States. Figure 4 shows the breakdown in the use of synthetic types of material by application. The largest requirement is for use as a carbon addition in iron and steel. This is followed by alkaline batteries and friction materials. Current technological opportunities New opportunities for graphite products are now being developed. These new areas are made possible due to the advances in graphite thermal technology. The ability to purify and modify graphite and carbon products is the key to future growth in the graphite industry. New, higher-purity, more consistent graphite products are leading to enhanced performance in current applications. They are also opening the door to new applications.

Jan 1, 1997

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine or the expansion of an existing mine can range from nine to 24 months, or even longer. The time frame will vary depending on whether an environmental assessment (EA) or an environmental impact statement (EIS) will be completed Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. In this paper, a two-year natural resource baseline study by Homestake Mining for the Ruby Hill Mine, Eureka County, NV, is used as a case study to describe how a properly designed and executed natural resource baseline study streamlined the NEPA process.

Jan 1, 2003

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023