Search Documents

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By Robert C. Jones

The Henderson Mine, a new large scale underground development, is being developed by AMAX. The mine site is located about 50 miles west of Denver, Colorado, adjacent to the east side of the Continental Divide. The mine's three access shafts are in a narrow alpine canyon at an elevation of 10,400 feet. The ore body of molybdenite is to the south of the shafts, 3,000 feet below the surface of nearby Red Mountain. The ore extends over 800 feet vertically and is about 1,700 feet by 2,200 feet horizontally. The eastern and southeastern boundaries of the deposit are still to be defined at the present time. Development mining is advancing at the mine site on a three shift, seven-day basis at the rate of about 2,000 feet per month. About twelve miles of heading have been driven at the present time, and work to sink No. 3 Shaft has started. Development mining was begun in 1967 with the sinking of No. 1 Shaft. This shaft is fully concreted, 23 feet in diameter and 2,441 feet in depth. It is the mine ventilation exhaust conduit. It is also used for development muck hoisting, stand-by mine water pumping and secondary access to the 8,035 foot level. This level is the mine exhaust ventilation level and was mined principally by conventional rail mining methods. From this one station at the 8,035 foot elevation a 5% ramp was driven to the initial production horizon at 8,100 feet with diesel rubber tired mining equipment. Subsequent mining has been entirely by mobile diesel equipment at the mine site.

Jan 1, 1974

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By R. W. Smith

A number of investigators have studied the electrokinetic potential (?) of kaolinite as a function of pH. (1,2,3,4,5) These investigators all agree that the ? is negative except at quite acid pH values. The actual shapes of the curves reported by the several authors vary considerably. In spite of the general negative character of kaolinite the mineral has a rather high anion exchange capacity. (6,7,8) The cation exchange capacity is the lowest for the clay minerals. (6) It has been shown that anionic surfactants adsorb readily onto the mineral even up to neutrality, often in quantities exceeding the reported anion exchange capacity. (7,8) At least part of the anionic adsorption should be onto positive edge sites thought to exist on the mineral. (9,10) In the present study ? of kaolinite was measured as a function of pH using both the streaming potential (sp) and microelectrophoresis (m.e.p.) methods. In addition ? was measured at various pH values as functions of sodium dodecyl sulfate (SDS) and trimethyldodecylammonium chloride (TMDAC) concentrations. In some experiments decyl alcohol (DA) was added.

Jan 1, 1968

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By S. B. Keith

Cerro de Pasco Corporation operates five large base metal mines in Peru having a combined production of some three million tons of ore a year. An integrated complex of concentrators, smelters and refineries produces annually about 25,600 short tons of copper, 48,100 short tons of lead, 60,500 short tons of zinc metal, 102,300 short tons of zinc concentrate, 8,272,000 ounces of silver and substantial amounts of bismuth, cadmium and selenium. Geology plays an important role in these operations. The organization of detail geologic work in and around the Cerro mines was set up by John M. Boutwell in 1918 and a geology department was established in 1920. Growing through the years, the department technical staff now numbers over thirty men and. their work covers all phases of geological investigations. Many outstanding geologists of the past and present, too numerous to name here, have studied and contributed to the knowledge of the deposits and the ever growing list of Cerro "alumni" must rival that of any other mining organization. Numerous papers on the geology of Cerro's mines can be found in the technical literature and several doctoral theses have been presented on Cerro subjects as indicated in the attached bibliography, Specimens of Cerro's ores can be found in museum, college and university collections throughout the world. Yet, as with all mines and mining districts, the geologic knowledge of Cerro's deposits in Peru is being revised and added to constantly. This presentation cannot hope to cover adequately all the phases of the geology and mineralization. For a more complete background and discussion of the mine you are referred to the bibliography. Here I shall outline only briefly the more important geologic features and describe some of the newer developments of recent years The credit for the data presented here belongs to the many geologists who have worked or are now working for Cerro de Pasco Corporation, but I must assume sole responsibility for any omissions or variations in the interpretation of their work.

Jan 1, 1965

By R. R. Klimpel

This paper demonstrates, using the results of an unusually complete industrial test sequence, what the various interactions are between grind size, collector dosage, and frother type. While particle size is universally acknowledged to be important in optimizing industrial copper sulfide rougher flotation circuits, many of the various interactions that do occur at the industrial level with particle size are still being identified and/or quantified. This study also presents, in a consistent manner, the changes in flotation kinetics that occur as a function of particle size, in a typical industrial circuit along with some insights as to how flotation operators can optimize rougher circuit performance.

Jan 1, 1993

By J. W. Leonard

By using physical and chemical method to increase the bulk density of newly mined coal, the productivity of a mine can be significantly increased. Greater amounts of coal can be placed in fixed volume shuttle car by increasing bulk density. This can increase mine productivity by about 15%. Small, easy to achieve changes in mining operations are required to obtain the increased productivity. This article deals with chemical methods used to increase coal bulk density, the results and discussion are based on experiments performed in the laboratory.

Jan 1, 1992

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By J. J. Moore

Combustion synthesis or self propagating high temperature synthesis (SHS) reaction systems are discussed with respect to thermodynamics and kinetics. In particular, tile effect of the process parameters, ego particle size, AHf, ignition and combustion temperatures on these self sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall activation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti -X intermetallic shape memory alloys, TiC-Al2O3 and ZrB2 ?Al2O3 ceramic composite materials.

Jan 1, 1991

By John G. Holmes

The generation of low cost power is but one phase of the TVA program for regional development. During the 36 years since TVA began, growth in its generation of electric power has necessitated a shift from a predominantly hydroelectric power system to a combination steam and hydroelectric system. The addition of steam-electric power plants to TVA's generating system was necessitated by the rapid increase in the traditional and defense demands for electric power in the 80,000-square-mile area served by TVA, the need to firm up the hydroelectric power, and the fact that all available sites for sizeable hydroelectric projects had been developed. At present TVA owns and operates 40 power plants--29 hydroelectric and 11 steam-electric plants. The total generating capacity of the hydroelectric plants is 3,105,430 kw, and the capacity of the steam plants is 13,951,135 kw. This provides a total generating capacity of 17,056,565 kw for the plants operated by TVA. Individual capacity of the 112 hydroelectric units ranges from 10,000 to 67,500 kw, and the individual capacity of the steam-electric units now in operation ranges from 60,000 to 950,000 kw. In addition to this generating capacity, TVA distributes the power from 6 U. S. Army Corps of Engineers hydroelectric plants on the Cumberland River. These plants contribute an additional 725,000 kw. Also, under an agreement with the Aluminum Company of America, TVA directs the stream flows and generation of their 423,715-kw system on Tennessee River tributaries and shares with Alcoa in the increased generation resulting from this coordinated operation.

Jan 1, 1969

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By V. J. Hucka

A 0.5 m (20 in) diameter high pressure natural gas pipeline crosses over a coal mine located in Central Utah. Ground movement induced by the mining operation could possibly place excessive strain on the pipeline causing it to rupture. The mining operation extracts coal from two seams using the room and pillar method. The seams are situated one on top of the other and both lie directly under the pipeline. At present, only the upper seam is being mined beneath the pipeline. However, in the future, the mining operation of the lower seam will also affect the pipeline. As would be expected, mining of both coal seams causes surface subsidence. This is especially true when the pillars are extracted during retreat.

Jan 1, 1983

By J. A. Jirestig

Laboratory investigations on the possibility for magnetic separation of sulphide minerals are reported. A survey of several sulphide ores and flotation concentrates shows that magnetic separation in most cases is not a suitable primary method of beneficiation. However encouraging results have been obtained in concentrate purification. At the Boliden complex sulphide ore concentrator in Garpenberg a Allis-SALA MK III carousel High Gradient Magnetic Separator (HGMS) is used together with a small flotation circuit to recover sphalerite lost to the galena concentrate in lead flotation. The result after four years of refining the HGMS process, show increasing zinc recovery and enhanced quality of the lead concentrate.

Jan 1, 1993

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987