Search Documents

By Poltak Sinaga

PT Kaltim Prima Coal's 13.1 km overland conveyor was commissioned in 1991. It is of conventional 3 roller 350 troughed belt type. Cost and performance optimisation during initial design ended up with 5.4m/s belt speed, 1,000mm belt width to convey 1,350tph, and 7mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1,100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30mtpa. Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4200tph satisfactorily.

Jan 1, 2008

By W. Zhang

"The adsorption of collector on chalcocite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on chalcocite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. The result clearly shows that the adsorption of xanthate on chalcocite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. AFM images also showed that increasing solution pH to 10 doesn’t prevent the adsorption of xanthate on chalcocite much and the result confirms with the fact that chalcocite floats well in a wide pH range up to 12 with xanthate being used as a collector. INTRODUCTION In flotation, the adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying metal recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) The adsorption of xanthate on chalcocite surface in aqueous solution also attracted the interest of many researches. Gaudin and his colleagues (Gaudin et al., 1934; Gaudin and Schuhmann, 1936) studied the solubility of potassium ethyl xanthate and its reaction products in organic solvents and firstly proposed there was initially chemisorbed xanthate (X-) on chalcocite surface followed by insoluble cuprous xanthate (CuX). Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of chalcocite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on chalcocite was cuprous xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Richardson et al. (1984) carried out an electrochemical study of chalcocite flotation with the addition of ethyl xanthate. It was proposed that cuprous xanthate and possibly cupric xanthate were adsorbed hydrophobic species on chalcocite surface due to the exchange and charge transfer oxidation reactions. Leppinen et al. (1989) applied an in-situ FTIR study of ethyl xanthate adsorption on sulfide minerals under conditions of controlled potential and they concluded that, for chalcocite, there were three different potential regions of xanthate adsorption, including chemisorption, copper ethyl xanthate formation on the surface and multilayer formation."

Jan 1, 2015

By D. Shuck

Incorporation of a 2,727 mtpd, $5.7 million flotation circuit into the Mclaughlin flowsheet was completed in November 1991. This capital addition reduced overall operating costs and improved the gold recovery of the low grade refractory reserves over that expected for direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate which is utilized to supplement feed to the pressure oxidation circuit.

Jan 1, 1994

By C. P. Boddy

One of the most difficult tasks a project manager will have in pre-mine planning is dealing with the mine site's hydrologic regime. Numerous federal statutes passed by Congress in the last decade have made the coal mining industry more responsive to the environmental impact during all phases of the mining process. Permitting these mines has dictated a cradle to grave approach in dealing with water related issues. This paper will attempt to explore the application of these technology- based laws and their direct application to the unique environment found in Alaska's interior regions.

Jan 1, 1985

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA's Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta's central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta's showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022

By J. J. Lewis

In the mid-1970's a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By M. M. Foss

Geophysical methods are gaining acceptance in the evaluation of coal mine ground control condition. The use of in-seam seismic investigations has contributed significantly to the body of information concerning ground control feature identification and analysis. Seismic methods have been used successfully in locating voids, faults, fracture zones, roof and floor rock interfaces, and more recently in characterizing in-seam stress distribution. Seismic tomography is an effective tool in data interpretation for several of these applications, but as is the case with other engineering application of geophysical techniques, there are limits as to how much substantive information can be interpreted from a given data set. This paper discusses some of the applications of in-seam seismic geophysical tomography, and the limits to which the transformation from raw data to information should be taken.

Jan 1, 1995

By Jr. Koch

Since 1882, world zinc production has increased. In contrast, United States zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the United States, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in United States production are due to economic, not geological, factors. Recent exploration has located large mineable ore bodies; additional deposits will undoubtedly be found in the strata-bound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the United States is in an early stage of the production cycle for zinc. Of major mining districts in the United States, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district.

Jan 1, 1980

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By J. R. Riding

In situ solution mining of uranium has environ- mental advantages over conventional mining. The leaching of uranium, however, alters the groundwater quality in the aquifer where the mining occurs. Currently, regulations require that the groundwater be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring groundwater quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By H. P. Rosenof

The G2 real-time expert system, a commercial product since 1988, is widely deployed in process, manufacturing and other industries. A number of innovative applications are installed or under development in the mining and metallurgical industries. These include: ? A chemical reagent control system for a mineral concentrator, at a mining company; ? A supervisory control system for a product dryer, at a surface coal mine ? A training system for equipment operators, at a steel mill; ? A scheduling system for furnaces at a hot rolling mill; ? A simulation system for mining operations; ? Several graduate-level research projects in materials handling at a university Realized and projected benefits will be discussed. In addition certain applications installed or under development in other industries will be proposed as applicable in mining and metallurgy. For example, applications for the management of vehicular traffic may find use in mining and shipping.

Jan 1, 1992

By Joseph Cervik

The mined coal bed and surrounding strata are both sources of methane which must be control led during mining. During developmental mining, the mined coalbed is the primary methane source; during retreat longwall mining, the primary methane source is the overlying strata. Underground technology is being developed to control both sources. This technology involves drilling long horizontal drainage holes into the mined coal bed and relatively short holes (less than 152 m or 500 feet) into the overlying strata. Because of the large volumes of methane that flow from such drainage holes and the limited ventilation available for in-mine dilution, underground pipelines are used to transport the drained gas to the surface. Large- scale in-mine degasification demonstrations showed reductions in methane flow of up to 70% during developmental mining.

Jan 1, 1981