Search Documents

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By M. Misra

It is estimated that the volume of low -level and intermediate level contaminants present in the soil at different DOE sites is of the order of several million cubic feet. The existing remediation scheme is containerization followed by burial in Land Disposal Facilities (LDF's) which is economically unattractive warranting the need to develop alternate remediation routes. One such route is the physical separation based volume reduction approach to removing a MINIMUM AMOUNT OF CLEAN SOIL with the radioactive particles, reducing the amount of material that requires disposal. The purpose of this study was to evaluate and test the feasibility of using physical beneficiation techniques for removal of contaminants from soil. The performance criterion was to recover at least 80% of the activity in 20% or less of the original contaminated soil volume. Four different radioactively contaminated (primarily uranium and plutonium) soils from DoE sites namely LANL, INEL, Fernald Plant 1 Storage Pad (ID-B) and Mound soils were tested using gravity, magnetic, gravo-magnetic, hydrocyclonic and flotation devices. The paper is divided into the two sections. The first section presents the overview of the Heavy Metals in Contaminated Soil Treatability Project conducted at the University of Nevada, Reno (UNR) describing the salient features of a state-of-the art Soil Washing Laboratory and the technology equipments used in the test program. The second section describes the soil characterization and typical volume reduction results obtained from the UNR tests. Among the physical separation processes, only flotation processes passed the performance criterion. For the LANL and INEL soils where the contamination was contained in coarse particle size, it was possible to recover more than 80% of the activity in less than 10-20% of the original volume of the soil thus rendering 80-90% of the soil "clean". For Fernald and Mound soils where contamination was of colloidal nature, flotation based processes showed encouraging results and are recommended for further studies.

Jan 1, 1995

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By A. K. Sheik

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By T. Negeri

Flotation is the most efficient and preferred solid-solid separation method in mineral processing. However, enhanced production of high-grade concentrates at sufficiently high recovery still poses technological challenges to-day. A novel flotation method to produce final-grade concentrates from finely-ground ores in a single step is being developed and tested by CANMET. For the complex sulphide ores tested, grades are superior while recovery is considerably improved. Furthermore, concentrate production rates, at similar recoveries, are faster than for the conventional rougher-scavenger-cleaner configuration. This paper discusses the physical operating parameters affecting Cu-Zn flotation metallurgy.

Jan 1, 1995

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez, Nishan Pokhrel, Lizeth Jaramillo

This paper presents a case study of respirable dust characterization in a thin-seam coal mine in southern West Virginia. Samples were collected in various locations within the mine and analyzed using scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), thermogravimetric analysis (TGA), and Fourier transform-infrared (FT-IR) spectroscopy. The study found high non-carbonate mineral content, particularly aluminosilicates and silica, in the dust. The results indicate that fine aluminosilicate particles may interfere with SEM-EDX analysis, leading to an underestimation of coal content. The findings highlight the importance of using multiple analytical methods to accurately characterize respirable coal mine dust.

May 5, 2022

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By A. T. Yu

Two key components make up the core of a rapid excavation operation. They are: the breaking up of the rock and its removal. Owing to the complexity inherent in mechanical rock-breaking and the relative infancy of the art, for a number of years the first of these two components has received virtually undivided attention from the industry. Only recently has some concern been expressed about the technology and the economics of the much ignored second component: muck removal. As the continuous boring machine's percentage downtime continues to trend lower in the future, the need for adequate and more effective materials handling systems in rapid excavation will become increasingly more acute. (1) Recognition of the need for a broader and more far-sighted approach to our problem has been eloquently underscored in the conclusions of the Committee on Rapid Excavation sponsored by the National Research Council: "Ultimate attainment of the desired cost and speed improvements is significantly dependent on recognition of the excavation process as a system whose subsystems are critically inter-related. Substantial amounts of full-scale field testing of integrated driving, muck removal, and support subsystems are required." (2)

Jan 1, 1997

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have ben made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modelling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developped, which can be calibrated far ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables to predict the complete composite particle distribution, and is thus valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1985

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that, overall, the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In common practice, however, coal blending is at best coal mixing. If necessary, more sophisticated blending systems can produce a more homogeneous feed by using accurate weighing devices and on-line coal analyzers coupled with sampling systems. Blending can be accomplished at the mine, on stockpiles, and from bins, bunkers, and silos.

Jan 1, 1994

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987