Search Documents

By P. James

"INTRODUCTION Dissolved salts build up in leach solutions over time as leach solutions mature. Iron can be particularly problematic for hydrometallurgical copper production as it can compete with copper for separation during solvent extraction (SX), leading to iron bleed through and reduced electrowinning (EW) efficiency. In its ferric form (Fe+3) it precipitates as a hydroxide at fairly low pH and can promote clogging and disrupted flow within leach pads as a result of localized pH deviations – such as might result from weather events. The solids formed can cause relatively irreversible degradation to pad productivity. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. The precipitation pH point for solids formation falls as the ferric (Fe+3) concentration increases, making the issue more prevalent as leach circuits for ore bodies containing appreciable iron get older. It can also be more of a concern when leaching lower grade ore like tailings where lower copper content may increase iron/copper ratios which may increase iron accumulation rates. Control of ferric (Fe+3) levels could be used to lower ferric (Fe+3) levels and keep the ferric hydroxide [Fe(OH)3] precipitation pH sufficiently high to avoid the associated solids formation and potential leach pad occlusion. Control of ferric (Fe+3) and ferrous (Fe+2) tenors and ratios may also provide benefit for improving sulfide ore leaching or bioleaching performance and effectiveness. Traditionally options for such control were rather limited with bleeding contaminants off or chemical dosing treatments being prominent methods. Now Blue Planet Strategies introduces a new option. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DeMet™ (Dynamic Electrolytic Metal Effluent Treatment) platform is highly effective at efficient low-cost conversion and control of iron content in leach streams in addition to targeted dilute metal recovery.[1-6] This powerful new capability provides a new treatment opportunity to control leach solution ferric (Fe+3) and ferrous (Fe+2) tenors to enhance leach operation production."

Jan 1, 2015

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983

By S. K. Jena, S. Singh, B. Das, N. Dhawan, P. K. Misra, D. S. Rao

"Iron as an impurity in pyrophyllite ore affects pottery, ceramics and tile quality. We carried out the characterization of a pyrophyllite ore sample using optical microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and wet chemical analysis. The study revealed the presence of 2.15% iron oxide (Fe2O3 ) along with silica and alumina as the major components, which constituted around 90% of the total sample. We carried out the removal of iron from the pyrophyllite using magnetic separation and acid leaching and found that wet high-intensity magnetic separation (WHIMS) could remove 28% of iron values while oxalic acid leaching could remove up to 99.3%. The leaching kinetics of iron removal and the effects of pulp density, acid concentration, leaching time and temperature were also investigated. The optimum conditions for leaching were found to be leaching time of 60 minutes, temperature of 90°C, pulp density of 5%, oxalic acid concentration of 0.3 M, and particle size below 100 microns. Iron dissolution from the pyrophyllite sample can be best described by the diffusion of ions through the product layer of constant-size spherical particles. The breakdown of the pyrophyllite structure was evident from the FTIR and TGA studies. The activation energy of the leaching process over the temperature range was calculated to be 43.47 kJ/mol. IntroductionPyrophyllite is a naturally occurring phyllosilicate mineral composed of aluminum silicate hydroxide [Al2Si4O10(OH)2] as the major component and often associated with other minerals such as kaolinite, mica, quartz, rutile and epidote. It occurs in fine-grained sericite schist that is quarried as pyrophyllite (Pandit et al., 2008). In India, pyrophyllite occurs mainly in Madhya Pradesh state, Uttar Pradesh state and the Keonjhar district of Odisha state (Harpavat, 1995). Pure pyrophyllite is a highly desirable material for various applications due to its unique properties. It exhibits high refractive behavior, low thermalelectrical conductivity, low expansion coefficient, low hot-load deformation, low bulk density and high corrosion resistance to molten metal and basic slag (Rieger, 1997). It is used in the ceramics, refractory, foundry, electrical-insulation, sanitary-ware, glassmaking, pesticide and rubber fields. Compared with clay, it has lower thermal conductivity and coefficient of expansion, making it more suitable for refractory applications (Harben, 2002; The Minerals Yearbook, 2011)."

Jan 1, 2015

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By Elisa Comis, Barbara Bitetti, Julien Pepiot, Stefano Lione, Francesc Rich

The new Lyon-Turin railway project involves the construction of a 57 km twin-tube tunnel between France and Italy. Pini France (project leader) and Systra-SWS are the designers of Construction Site 8 (CO8). This part of the project includes the construction of the tunnel portal on the Villard-Clément platform, two 2.8 km long tubes of the base tunnel in the direction of Saint Martin la Porte, the cross-passages between tubes and the niches. This paper presents the general approach followed to design the temporary support for the base tunnel, cross-passages, and technical rooms. The design of the temporary support accounts for the variability of the ground and water conditions, the excavation attended behavior, the construction planning and the identified geological hazards that could be encountered along the alignment. Particular attention is paid to the intersections between the tunnels both in terms of numerical modelling and construction methods and phases. Two types of intersections are present in the project: the intersections between the cross-passages and the base tunnel and the intersections between the base tunnel and the niches. 3D models have been developed for the tunnel intersections.

Jun 23, 2024

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By S. Chatterjee, S. Bandopadhyay

A spatial modeling technique based on the Bayesian neural network (BNN) is proposed. Incorporation of the Bayesian method for posterior probability of the output parameter helps calculate the uncertainty associated with the estimate. Parameters of the BNN model were selected using a grid search algorithm. The expected value and the variance of block support were calculated by Markov chain Monte Carlo sampling of the posterior distribution at discretized points within the block. The BNN model was validated by applying it to the Walker Lake data set and comparing the results with ordinary kriging results. The comparison revealed that the proposed BNN method performs marginally better than ordinary kriging. The variance map is less smooth than with ordinary kriging, and the proportional effect is less in the BNN-based model than in the ordinary kriging model. The developed BNN model was applied to the Coho block of a placer gold deposit in Nome, AK. Results reveal that the BNN model is globally biased for the Coho block and underestimates the sample mean. The grade volume curve was developed by calculating the block mean and block variance after discretizing the block into a number of points and applying the BNN model to each discretized point.

Jan 1, 2011

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne's Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By C. H. Stephenson, Z. White

This paper presents the design approach case study for incorporating a Technogrid® conveyance End-of-wind arresting system within the new South32 Hermosa headframe. Focus is placed on energy absorption requirements, structural integration, and mounting details tailored to the geometry and operational constraints of the headframe. Key considerations include arresting forces, load path continuity, and connection design to ensure reliability and maintainability. The paper also discusses coordination with other headframe systems and the iterative design process used to meet safety standards and client objectives.

Feb 22, 2026

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By J. G. Groppo

The Andritz Ruthner Inc. hyperbaric filter was evaluated at a pilot scale for dewatering fine coal cleaned by froth flotation. The pilot scale dewatering testing was conducted at a solid feed rate ranging from 100 lbs to 200 lbs/hr-ft2. Effect of hyperbaric operating parameters and addition of various surfactants and flocculants were evaluated on dewatering of fine coal. The tests data indicated that for the minus 100 mesh and minus 28 mesh clean coal product, the Andritz hyperbaric unit provided filter cake containing 23 percent and 14 percent moisture, respectively.

Jan 1, 1996

Because of its many advantages, roof bolting has been widely used in hard-rock underground mines. In this paper, the applicability of roof bolts to mine openings in frozen ground, and the affects of bolts on the stability of the openings are presented. A comprehensive finite-element program, ABAQUS, was used to analyze the temperature distribution, the stress field and the displacement, field around a mine opening. Openings that were supported by roof bolts and openings that were unsupported were both analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration, i.e., a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts is less than five, the displacement within the ground can be improved only locally.

Jan 1, 1997

When a company like Lonmin, the third largest platinum producer in the world, is mining one of the most precious metals in the world, time is money. Every piece of equipment is expected to be in top shape because every minute of downtime can add up to lost profit. Two different types of platinum ore are mined and processed by Lonmin, namely Merensky and UG2. Merensky has a grade of 3.5 g/t (0.1 oz/st) and UG2 has a grade of 4.5 g/t (0.13 oz/st). The mine also produces platinum group metals (PGM), which consist of platinum, osmium, palladium, rhodium, iridium and ruthenium. Although South Africa has more than 80 percent of the world?s PGM reserves, these minerals are very scarce. Lonmin is considered a low-cost producer of these minerals, generating 21.5 t (694,000 oz) of platinum and 18.6 t (600,000 oz) of PGMs in 2012. So when the company?s Karee K3 concentrator plant in Rustenburg, North West Province, South Africa, was experiencing high operating costs on the transfer points, a solution was needed.

Jan 1, 2012

By W. M. Cross

The use of fillers and reinforcements for plastics has increased considerably over the past few decades. For example, in the 1980's the average growth rate of filler use was 5.8%. [Katz and Milewski, 1987] Similar filler use growth rates occurred in the 1970's due largely to the increase in price of petrochemical starting materials for plastics. While filler use is still sometimes predicated on the cost benefits associated with their addition to the plastic, other mechanical and performance advantages associated with filler addition are being realized, and account for most of the increased usage. Plastic filler types are many and varied, and include both inorganic minerals/metals and organic compounds, with the former type being, by far, the more common. Common mineral fillers include oxides, including both natural and synthetic silica; carbonates, particularly calcium carbonate; clays such as kaolin; and silicates like mica and talc. It has been recognized that a number of factors influence filler performance, including particle size, shape, surface area, and hardness to name a few. In addition, the interaction between the filler and the plastic is of paramount importance as this interaction will determine the wettability, bonding and the adhesion between the two materials, and ultimately, the mechanical properties of the composite. Froth flotation has long been recognized as a viable process to separate different mineral types. [Leja, 1982] Prior to flotation the minerals are liberated from the ore by comminution. The mineral particle size range produced by this comminution process is typically between 300 and 10 microns. This size range is also typical of mineral fillers for plastics. The size similarity between mineral fillers and minerals concentrated by froth flotation is only one of many similarities that can be found.

Jan 1, 1997

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By Ronald M. Hays

During the twentieth century the Mesabi Range in northeastern Minnesota has been the major source of iron ore for American steel mills. The Mesabi Range extends along an iron bearing outcrop known as the Biwabik formation. This outcrop is some 120 miles long and up to three miles wide. The formation is from 200 to 650 feet thick and dips 5 to 10 degrees to the southeast. The iron content of the original Biwabik formation was quite uniform, but much of this formation has been subjected to alteration. Thus major variations in iron content and mineral composition exist both laterally and vertically in the present Biwabik formation. The remaining unaltered iron formation includes the magnetic taconites which are commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons. per year of iron pellets and have produced approximately 170 million tons of pellets since 1956. Capacity for another 30 million tons per year of pellets is being considered by the industry for the next ten years. This increase will be obtained by construction of new plants and expansion of present operations. Thus by 1977, it is estimated that approximately 60 million tons per year of iron pellets will be produced from magnetic taconite on the Mesabi Range. The portions of the Biwabik formation subjected to intense alteration resulted in the direct shipping, wash and heavy media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron for American steel mills. In 1966, 12 million tons of direct shipping ore and 18 million tons of wash, jig, heavy media and other gravity concentrates were shipped from the Mesabi Range. These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from about 30 million tons in 1966 to 6 to 8 million tons in 1975. This decrease will be due to depletion of reserves and poor quality product.

Jan 1, 1968

By Paul D. Tomlingson

Part one of this two-part series covers conceptualizing and developing a maintenance information system. It explains what information is necessary to manage such a system. Next month, part two will discuss using this type of system with administrative information, including error and absentee reports as well as open work files. Introduction There is no doubt that quality, timely, and accurate information can make a solid contribution to maintenance cost reduction objectives. Yet, despite obvious benefits, methods being used to acquire information systems are proving costly, frustrating, and often unsuccessful. Those needing the information are disappointed. Mine managers, hoping to reduce costs with quality information, are instead seeing no system, no savings, and massive spending on information endeavors of questionable benefit. Options Any software vendor will happily sell you his program. Numerous mining organizations, having "gone to the cleaners" themselves, will gladly make their programs available to help cover huge trial and error development costs. Any package can only be a generalization. Any program bought from some other organization must undergo numerous modifications to make it work properly. In the process the initial cost is doubled. Many mining maintenance organizations do not know how to go about the task of conceptualizing, developing, installing, and effectively using a maintenance management information system. Consequently, many have hedged their primary responsibility of specifying what information they want, how they will get it, and how they will use it effectively. Into this void have jumped many who claim they can help. But some may not understand the special information needs of maintenance in the mining industry. By default, the whole scene of maintenance information systems has become confused and in need of clarification. A Starting Point Four broad phases are used to organize the steps by which maintenance acquires an effective maintenance management information system and initiates its use. Conceptualization is an identification of needs, factors that influence development, and an assessment of support for the system. Development is a plan of action for bringing the conceptualized information system to life. Consideration is given to the practical aspects of collecting field data, processing it, and converting it into useful information. Implementation consists of those actions by which the newly developed system is integrated into the organization and put in the hands of its personnel so that its value can be derived. Use addresses the means by which personnel use the information to accomplish maintenance improvement objectives. These phases are preceded by establishing the need for the information system. They are followed by a requirement to measure its success (Fig. 1). Conceptualizing the Information System Responsibilities - The information system user must acquire the system best suited for its use. A step-by-step process is essential to avoid many serious problems than can easily occur. The most important step is to clearly identify its objectives and lay out a course of action to achieve those objectives. The major reason for the failure to achieve information objectives is not carrying out this responsibility. Maintenance cannot delegate the task to data processing. It can obtain technical assistance but it must retain responsibility. Nor can maintenance purchase

Jan 7, 1985