Search Documents

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By F. F. Peng, S. S. Peng, V. Z. Sun

A detailed study of ponding phenomenon relative to surface subsidence due to longwall mining was conducted for various surface stream conditions. Based on field monitoring, the stream-ponding process and three forms of stream water are described. Also discussed are the criteria of stream ponding and the influences on the ponding process by two key factors: the angle of stream flow and the change in the stream-bed gradient. A numerical (mathematical) model, which combines trend surface technique that describe the topographical features in the vicinity of a stream and the modified influence function, which represents the profile of the surface subsidence trough (or basin), is constructed to predict the formation characteristics of stream ponding in terms of location, boundary and accumulated water volume of migratory and stationary ponds produced by the stream-ponding process. Three cases are analyzed using the model to predict the interaction of the underground operations and the environmental impact due to stream ponding. The feasibility of various mitigative measures are assessed.

Jan 1, 1997

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990

By DeVerle Harris

The enthusiasm with which individuals have participated in mineral exploration in the development of this country testifies to the fact that there was once a very real probability of making a worthwhile discovery. Over the years, the discovery and subsequent exploitation of the accessible ore deposits have made the finding of new deposits progressively more difficult. Present day mineral exploration has evolved from the lone prospector with the grubstaker behind him to a very costly and complex business, involving large sums of money and a staff of experts in the fields of exploration technology. Exploration today must be carried out on a large scale to be profitable. With the involvement of large amounts of capital, there has been a good deal of interest in methods of optimization of the allocation of the resources of a firm 'engaged in mineral exploration. As a step toward this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firms operations so as to optimize its profit objective or more simply, to make exploration more efficient and effective.

Jan 1, 1964

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By A. S. Ericson, J. H. Corrigan, E. J. Jahnsen

Calcine is transported from the Reduction Plant at 850°C in insulated hopper cars and charged into three rectangular electric melting furnaces each equipped with three - 18.5 MVA transformers. The electrical energy is applied through six in line prebaked carbon electrodes, and slag and metal are tapped at opposite ends of the furnaces on an intermittent basis. The slag, 5000 tonnes per day, is disposed of by a pot train directly to the dump. The ferronickel, 250 tonnes per day, is tapped into 40 tonne capacity ladles in which it is refined in two ASEA-SKF ladle furnace stations. Casting is done over lip at 1520°C in a pig casting machine with stepless speed control at up to 55 tonnes per hour. The ingots are stacked into self palletizing bundles weighing about 1500 kilograms and are strapped and tagged and transported to the seaport, from which the final shipment is made to the world market. The paper describes constructional details and gives information of both normal operation and start-up and shut-down procedures. Consumption figures for refractory, electrodes, electric energy and refining additions are given and metal chemistry is given before and after refining.

Jan 1, 1979

By Indranil Roy

Gua supergene enriched iron ore deposit from Jharkhand, India has been geostatistically modeled. Population modeling shows a negatively skewed 3-parameter log-normal fit for Fe and positively skewed 3-parameter log-normal fit for Al2O3 and SO2. Semi-variographic studies for Fe indicate spherical function fit using point kriging cross-validation technique with Co=4.06(%)2, C5.11 (%)2, Co+C=9.1 7(%)2 and 'a'=348m. Kriging with 50mx50mx 10m block size at 740mRL led to a global mean kriged estimate of 61.98% and kriging variance of 4.04(%)2 for Fe with central 90% geostatistical confidence limits at 61.39% and 62.24% for that level. This led to an ore inventory at 740mRL as 7.29 million tonnes of ore.

Jan 1, 2002

By Regina N. Tempel, Laurie S. Balistrieri, Lisa L. Stillings, Lisa A. Shevenell, Maggy F. Lengke

Dexter pit lake, within the townsite of Tuscarora, Nevada, has been in existence since 1990 and provides a natural laboratory for the study of cycles of trace elements associated with ore deposits (e.g. As, Cu, Pb, and Se). Our goal in this study is to develop and calibrate methods of geochemical modeling that may be applied to estimating the concentrations and fluxes of trace elements in pit lake systems. Our initial modeling work considers limnology, hydrology, wall rock mineralogy and geochemistry, benthic fluxes, and colloid composition. Results from our work may be useful in evaluating water quality in the arid West.

Jan 1, 2000

By D. S. McAllister, P. M. Rice, M. E. Fowler

The Westside Light Rail Project, a major 19.3-km (12-mile) extension of Portland, Oregon's light rail system, includes 4.6 km (2.8 miles) of twin 5.8-m (19-ft) diameter running tunnels, a binocular type station which, at 80 m (260 ft) below the ground surface, will be the deepest mass transit station in North America, two 9.4-m (31-ft) diameter station access shafts, and a 5.2-m (17¬ft) diameter ventilation shaft. The tunnels are being excavated by TBM and conventional rock, soft ground, and mixed-face methods. Geologic conditions, alignment, underground opening design, excavation method selection, and payment provisions for excavation and initial ground support are discussed.

Jan 1, 1995

By J. Smolensky, M. Paul

The Nordhalde is a waste rock pile resulting from uranium mining near Ronneburg, Germany. The pile contains over 27 million m3 of waste rock. Typical seepage water has a pH of 2.7 and a sulfate concentration of 10,000 mg/L. Geochemical investigations of the Nordhalde from 1993 to 1996 included drillholes, test pits, ABA and metals analyses, column tests, and a detailed review of the construction history of the pile. In 1996, eight drillholes were instrumented for monitoring oxygen and temperature. Monitoring continued for a fill year. Hourly temperature and pressure readings were taken by automated data recorder. Oxygen concentrations were measured three times per week, and periodic gas samples were obtained for complete analysis. The resulting data set is believed to be one of the most comprehensive of its kind. Effects noted elsewhere, such as thermal convection, are evident. However, unlike other data in the literature, the NordhaIde data shows a strong seasonal effect, with convection dominating oxygen transport only in the winter months. Analysis of the data allowed the amount of contaminants associated with ongoing and historical oxidation to be compared, and results were used to assess the potential effectiveness of proposed remediation measures.

Jan 1, 2000

By Julián M. Ortiz, Antoine Caté, Oy Leuangthong, Ilkay S. Cevik

Mineral resource classification relies on the expert assessment of a qualified person (QP) to determine which blocks of a 3D mineral resource model are classified as measured, indicated, or inferred. The decision is often based on a combination of quantitative parameters related to the estimation process and qualitative decisions based on previous experience or preconceptions not captured in the numerical model. As such, the procedure is subject to inconsistency, that is, blocks with similar qualities may end up in different categories, mainly due to the subjective nature of the approach. In this paper, we present a methodology to assist the qualified person in this task by clustering blocks with similar parameters and then classifying them into categories in a consistent and automatic manner that only requires the specification of a few hyper-parameters. The result is a consistent classification into resource categories comparable to the result of a classification done by a qualified person but fully consistent and generated in a short time frame. The procedure begins with repeatedly sub-sampling the block model to determine a distance matrix using an unsupervised random forest approach and then clustering the blocks using the associated distance matrix. Then, all the blocks in the model are classified using a supervised random forest approach, which gives a probability of belonging to each class. The initial class can be determined from the class probabilities. Support vector classification with a radial basis function kernel is utilized to smooth the boundaries between classes and define the final classification. An approach to tune the hyper-parameters of smoothing is provided. The methodology is demonstrated with two examples from two gold deposits. Results are comparable to the classification done by the project qualified person using conventional methods.

Aug 17, 2021

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By Gary F. Meenan

The industrial practice of froth flotation for upgrading the quality of fine coal is a relatively complex, expensive, and inefficient process when compared to the coarse- and intermediate-size coal cleaning circuits. The differences in cost and process efficiency can be attributed mainly to the lower equipment throughput, the added cost of flotation reagents, and the fact that flotation is typically a manually operated process susceptible to fluctuating feed characteristics that influence the overall operating efficiency. The emphasis in recent years has been on improving the flotation process efficiency and lowering the cost per clean ton. This has been achieved by larger flotation cell designs, implementation of flotation reagent evaluation programs, and improved process instrumentation and control. These developments are reviewed along with other current coal flotation practices.

Jan 1, 1999