Search Documents

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By William X. Chavez

The Mantos Blancos copper-silver district is located in northern Chile about 45 kilometers northeast of Antofagasta, as shown in Figure 1. Disseminated and veinlet copper and copper-iron sulfides containing economically significant silver values are hosted by andesitic to rhyolitic volcanic rocks of probable Jurassic age (Chavez, 1983). Field, mineralogical, textural and lithochemical evidence show that three major alteration types may be recognized within the district: (1) district-wide sodium metasomatism, manifested as albitization of feldspars and development of albite veinlets and pore-fillings, (2) local to widespread, incipient to intense addition (chloritization) or removal (bleaching) of magnesium and iron and (3) local to widespread, moderate to intense hematitization, usually spatially associated with bornite-digenite-covellite (as specularite) or digenite-covellite-chalcocite (as red hematite staining with or without specularite) mineralization. Carbonatization, occurring as veins, veinlets, vesicle fillings and irregular patches of calcite, varies in magnitude of development but is widespread. Sericitization of feldspars and groundmass is only locally intense yet is generally present as incipient alteration throughout the district. The district-wide albitization of the Mantos Blancos volcanic sequence has altered what were originally more potassic and calcic, less sodic, rocks to what are now more properly referred to as keratophyres (Battey, 1955; Gilluly, 1935, Hughes, 1975). The petrographic and lithochemical characteristics of the three major alteration types noted above are summarized below.

Jan 1, 1984

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By Charles F. Herbert

The waves of prospectors who struggled across the wide Alaskan wilderness between 1898 and 19 10 came close to but did not actually find the rich copper/zinc/silver deposits strung out along 161 km ( 100 miles) of felsic schist in the remote Brooks Range of northwestern Alaska. They had heard rumors of gold in the valley of the Kobuk River, so they skirted the Arctic ice pack in the Chukchi Sea and, in a force at least 800 men strong, ascended the Kobuk River in 1898. Twenty-eight placer mining camps were established but only a handful survived for more than a few years. One of the placers that died rapidly was Ruby Creek. A map showing the location of Alaskan mineral deposits is given in Fig. 1. The Ruby Creek miners, disappointed with the scarcity of gold in that creek, followed copper-bearing float to two places where the float was especially plentiful. Pits, a short adit, and a shallow shaft uncovered copper carbonates, bornite, and chalcopyrite in fractured limestone but the remoteness of the district blocked efforts to sell the claims or to raise capital for development. Shortly after 1906, the copper prospects were abandoned and, except for an account published in 1913 by the US Geological Survey, they were forgotten, as were the names of the prospectors.

Jan 1, 1991

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By M. P. Evans, Rainer Kahrger

During the last decade or so great advances were made in the solvent extraction, electro winning technologies. They, combined with heap leaching, made it viable to exploit large, relatively low grade oxide copper deposits. The El Abra mine is a good example for such a deposit. Situated in Northern Chile at an elevation of about 4000m (14000 feet), 70 krn north of Calama, the El Abra deposit has been known for many years. In the early 1990's Codelco decided to sell a major holding in the deposit to international mining companies. After lengthy negotiations Cyprus Minerals finalized in June 1994 the purchase of 51% of the deposit with Codelco retaining the balance. lance. Already in 1993 Cyprus and the engineer on the project, began discussions with international materials handling companies with regards to the materials handling system required for the project. These early discussions were considered critical for this fast track project. Immediately after the notice to proceed with the project, several companies were invited to submit competitive conceptual proposals for that portion of the material handling system which was to transport crushed and treated ore from the plant to the leach pad and build the leaching heaps at a rate of up to 150 000 tons per day. A supplier was selected. Additional studies were made for the conveyor system from the mine to the fine crushing plant. Due to the extremely rugged terrain and high altitude at the mine, a decision was made to locate the plant and the leaching operations 15 km east of the mine at an elevation of 3400m. In July 1994 the supplier started the conceptual engineering with a design team at the engineer's San Francisco office. The undertaking was unique in the sense that the supplier's engineering team was integrated into the project for the duration of the conceptual engineering. The open and continuous communication greatly contributed to the success of the design work.

Jan 1, 1996

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By Justin Brown, Michael Kobler, Dave Ragland, Bob Shufflebotham

PROJECT OVERVIEW As the sun-bronzed San Diego students strolled casually to class, mining crews from Atkinson Construction were working only 9 meters below the surface. The330 meter long, 11.3 meter diameter squat ellipse NATM tunnel is part of the9.3 kilometer Mission Valley East Extension Light Rail Transit (MVE-LRT) being constructed for the San Diego Metropolitan Transit Development Board (MTDB). The SDSU segment of the MVE-LRT was awarded to the Clark Construction Group, the parent company of Atkinson Construction for $82.7 million. URS CORP was the prime designer and Hatch Mott MacDonald performed the NATM tunnel design. The construction managers were Washington Infrastructure Services with Underground Construction Managers, EPC Consultants, and ILF Consultants. A NATM tunnel design was chosen as the most cost-effective way to minimize disruption of the university activities. The tunnel passes close to several buildings and directly below access roads, tennis courts and a baseball field. The NATM method of conventional mining uses shotcrete for ground support often reinforced with steel orplastic fibers, welded wire mesh and lattice girders. The tunnel runs from a cut and cover box up a 4.2% grade in a 217 meter radius left-hand curve with several spirals and ends at the underground station 330 meters away. The depth of cover varies from 16 meters near the west portal to nine meters at the station. The design called for a two-pass system with a primary lining of 300 mm shotcrete with lattice girders at 1 m centers and two layers of welded wire mesh. The lattice girders are used primarily for profile control and are not considered a structural element. The top heading was designed to be excavated in one of three excavation sequences depending on ground conditions and depth of cover. In sequence one excavation, the top heading is excavated in two halves with a one-meter separation. In sequence two excavation, a side gallery is advanced 8 or more meters ahead of the

Jan 1, 2003

By Mark J. Schultz, William J. Francart, Michael P. Snyder

The Pittsburgh Safety and Health Technology Center surveyed MSHA Coal Mine Safety and Health Districts to monitor the implementation of computer based atmospheric monitoring systems (AMS) in underground coal mines. This survey was first completed in 1984, and has been periodically updated with the latest update completed in 1995. The utilization of computer based monitoring systems has steadily increased over the past 12 years, with over 16 percent of all producing underground coal mines using this technology in 1995. This paper discusses the results of the MSHA 1995 AMS Survey.

Jan 1, 1997

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By M. T. Ityokumbul

The effect of reaction conditions on the desulphurization of oil sand coke residues has been studied. The variables investigated were temperature, reaction time, heat transfer resistance, and mode of caustic soda addition. The results obtained show that oil sand coke desulphurization increases with temperature, reaction time, and heat transfer rate. In an oxidative environment, coke combustion during molten caustic leaching (MCL) commences at temperatures above 500°C. The mode of caustic addition has no effect on coke desulphurization.

Jan 1, 1995

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By Donald S. Bubar

The Separation Rapids property, located approximately 60 km (37 miles) north of Kenora, Ontario, Canada, is host to one of the largest rare metal pegmatite deposits in the world. This pegmatite was named the Big Whopper by its discoverer, Dr. Fred Breaks of the Ontario Geological Survey, because of the exceptional length and width of the surface exposure. The property is readily accessible from a main, all-weather road via a network of secondary logging roads. The main line of the Canadian National Railway passes through the village of Redditt, just 40 km (24 miles) south of the property. The Big Whopper is one of the complex-type (petalite sub-type) class of rare metal pegmatites that are geochemically the most highly evolved in the spectrum of granitic pegmatites. Such deposits are economically important as resources for the rare metals lithium, tantalum, cesium, and rubidium. While complex-type pegmatites are found in many areas of the world, most are too small to be profitably mined, however, with an inferred resource in excess of 15 million metric tons (mt) (17 million short tons [st]), the Big Whopper is only the fourth deposit of its type in the world with the size required to be of major economic importance. The other three deposits, which are currently in production, are the Tanco mine in Manitoba, the Bikita mine in Zimbabwe, and the Greenbushes mine in Western Australia. The Big Whopper is situated in the eastern continuation of the Archean Bird River greenstone belt which also hosts the Tanco pegmatite, approximately 60 km (37 miles) to the west. The principal commodities identified in the portions of the Big Whopper pegmatite explored to date are petalite (LiAlSi4010) and rubidium-rich K-feldspar. These are industrial minerals with important applications in the glass and ceramics industries. The Big Whopper also contains substantial quantities of lepidolite, a lithium, rubidium-mica which is the principal ore mineral for rubidium metal. Tantalum and cesium occur in anomalous levels with the petalite mineralization, and the possibility of finding zones of high enrichment in these valuable high-tech metals elsewhere in the deposit is excellent. Such enriched zones are typical of pegmatites as highly evolved as the Big Whopper. To date, the geological mapping and diamond drilling work completed by Avalon have delineated the Big Whopper pegmatite system over a strike length exceeding 1.5 km (0.9 miles), over widths ranging from 10 m to 80 m (30 feet to 260 feet) in thickness, and to a vertical depth of close to 300 m (1,000 feet), where it remains open. The pegmatite system consists of a vertically oriented massive petalite pegmatite dyke striking 280 degrees that is flanked by amphibolites containing a swarm of narrower albite and petalite dykes which have all undergone intense deformation in a high strain zone resulting in folding and intense shearing. The Big Whopper exhibits a mineralogical zonation pattern which is complicated by the superimposed deformation that has both folded and stretched the deposit. Drilling has defined a dilute geological resource totaling 7.1 million mt (7.8 million st) grading 1.283 percent Li20, 0.346 percent Rb20, and .007 percent Ta205 over a strike length of 600 m (2,000 feet), and to a vertical depth of 250 m (820 feet), where it remains open. The petalite and rubidium-rich-K-feldspars contained in the Big Whopper all appear to be of superior quality. The grades are consistent with a petalite content averaging 25-30 percent and a rubidium-rich-K feldspar content averaging 15-20 percent. The remainder of the rock consists mainly of albite, several types of mica, and quartz. Accessory minerals include columbitetantalite, cassiterite, apatite, garnet, and gahnite. Market studies show that the deposit is located close enough to existing transportation infrastructure to access rapidly growing, major markets in the glass and ceramics industries, both in the northeastern U.S. and Europe. There are only three competing lithium minerals producers in the world with the Bikita mine in Zimbabwe being the only major producer of petalite. The other lithium deposits produce spodumene, a less desirable lithium mineral. Lakefield Research Limited has successfully designed a process to produce an ultra-pure petalite concentrate containing up to 4.65 percent lithium oxide, and as little as 0.014 percent iron oxide, low levels of soda and potash, and negligible amounts of other trace elements. With these specifications, Avalon will have an excellent quality product for glass-ceramics applications such as Corningware®, CERAN® stove tops, and other thermal shock-resistant products. Lakefield is presently designing the balance of the flowsheet to produce separate concentrates of rubidium-rich K-feldspar, albite, mica, tantalum, tin, and high-purity quartz. Initial test work indicates that the feldspar products will be of exceptional quality. The K-feldspar concentrates contain 11-12 percent K20 and 1 percent Rb20, while the sodaspar contains over 10 percent Na20, and both have very low iron (0.01 percent Fe203). A preliminary economic model shows that with an initial production rate of 90,000 mt (100,000 st) per year, expanding to 170,000 mt (190,000 st) per year over 5 years, the project is capable of generating over CDN $10 million per year in pre-tax cash flow by year 5 on a capital cost of approximately CDN $30 million.

Jan 1, 2001