Search Documents

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By B. K. Cantrell

The use of diesel equipment in underground coal mines is controversial because "whole diesel exhaust" is regarded as "a potential occupational carcinogen" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2' and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols. The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.

Jan 1, 1991

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By D. Berberick

On January 5, 2012, the Mine Safety and Health Administration ordered the closure of the Silver Shaft, the primary underground access to Hecla?s Lucky Friday Mine, for removal of built up backfill material that accumulated over time on the shaft walls and furnishings. Lucky Friday and Cementation USA personnel worked quickly to identify the most effective means to get the mine back into production. The team developed a fast-track procurement and refurbishment plan utilizing shaft sinking winches, headframe modifications, a partial shaft sinking Galloway, and modified cages to not only complete clean-off of buildup, but also replace pipe brackets, shaft steel, and power and communications cables as needed in the 1,860 m (6,100 ft) deep shaft within 14 months.

Feb 23, 2014

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By Scott Lawson

BOB FALCONER: Our next topic leader is Scott Lawson. Scott is manager of human resources for Independence Mining Company, Cripple Creek and Victor Gold Mining Company, Victor, Colorado. Scott has 25 years of human resources management experience in the mining industry, surface and underground, precious and base metals. His topic this morning is "It's the Employee That Counts." SCOTT LAWSON: When reviewing the topic of productivity in a union versus nonunion workplace, we need to look at who, and not what, can make the difference in ensuring the success of a production-oriented operation. It's not explicitly whether the property is unionized or not, but whether the employee team (including the "management group") is working together to accomplish common, shared, and meaningful goals. The bottom line is what action or actions can be taken to develop trust and to strengthen working relationships that challenge and compel employees to willingly share their particular areas of expertise. I want to share a real-life experience that happened to me during the summer of 1961. Perhaps some of you will be able to relate to the following story. I was an 18-year-old fresh out of high school, ready for my first true work adventure. I found summer employment for myself and two friends with the New York Central Railroad in Cleveland, Ohio. Our jobs were as laborers, laying ties and rails, and unloading ballast. We made $2.62 an hour. We were fat cats! My friends and I took on the job with a great deal of vigor, to the dismay of our fellow workers. These workers were unionized by the Railway Workers, which I believe were affiliated with the Teamsters. Talk about being naive, we wrote the book in 1961. When we took the jobs, we did not realize the employees were represented by a union, even though we didn't think they worked too hard. Within our first two weeks of work, we established new daily records for laying virtually twice as many ties as had been standard, and we nearly tripled production by the end of our hall of fame railroad careers. We even took naively to the next level by lining up the ties for our afternoon work shift during our lunch break. In 1961, we thought we were the Mantle, Maris, and Colavito of tie laying. For the younger set in the audience, we would have felt like the McGwire, Griffey Jr., and "The Big Hurt" Thomas of tie laying. A section of the union contract allowed for a 60-day probationary period during which the employee was evaluated and also exempt from joining the union. I will venture to say that, to none of your surprise, on day 60 we were asked to join the union, and on

Jan 1, 1998

By Dirk Timmerman, Klaus Schönert

This paper reports on the results of research on counter flow classification of - 10 µm particles. Two classifiers were designed and constructed, the first semicontinuous and the second fully continuous. The latest version operates continuously with recoveries of fines up to 90% at feed loads of 30 vol.%, separation sharpness X25/x75 up to 0.83, without bypass and cut sizes down to 1.4 µm (x50 from separation efficiency curve).

Jan 1, 1995

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Firat Atalay

Estimating the spatial distribution of ore grade is one of the most critical steps to proceed with an investment decision on a deposit. Kriging is the most widely used method to estimate the ore grade, but alternative techniques are being developed. Machine learning algorithms can be used as alternative methods to classical kriging. In this paper, the iron (Fe) grade of a deposit is estimated with the XGBoost algorithm, and the results are compared with kriging estimation results. For the estimations, samples collected from drillholes were used. Due to the different natures of the estimation methods, different steps were taken to perform the estimations. The results show that XGBoost produced higher-range estimates, which is a desired result in ore grade estimation, and the minimum and maximum of the estimates were lower and higher than the kriging estimates, respectively. However, like kriging, the estimation results were smoother than composites, and the variance of the XGBoost estimates was lower than the variance of composites. This means that even though estimation with XGBoost mitigates the smoothing effect, the estimation results suffer from smoothing like kriging.

Dec 1, 2024

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By Kumara S. Rachamalla

Mineral activity in Ontario represents an annual production in excess of $4 billion. The Ontario government encourages the mining industry to undertake mineral development through grant programs and incentives offered by mineral resource taxation. Computers are playing an increasingly important role in improving productivity in the administration of incentive programs and the Mining Tax Act in Ontario. This has meant speedier processing of grant applications and tax returns which is resulting in a streamlined approach to incentives and taxation in Ontario. The use of computers has resulted in significant contributions to key areas of concern such as assessment of mining tax returns, analysis of the changes, if any, to the Mining Tax Act and modeling of the Ontario Mineral Exploration Program (OMEP). Implementation of state-of-the-art technology such as Local Area Networks (LAN's), fourth generation languages and integrated micro-mainframe information processing has resulted in improved productivity as well as lower costs. As a result, the respective services provided to the mineral industry by these two programs are now delivered in an efficient and cost-effective manner utilizing the latest available computer technology.

Jan 1, 1986

By Richard H. Johnson

White Pine Copper Company began operating a plant designed to recover copper matte particles from its discarded reverberatory furnace slags in April, 1972. Seasonal operation, generally the months of April through November, continued through October, 1974, shutting down due to feed exhaustion. White Pine reverberatory furnace slags contained economically recoverable amounts of copper for a variety of reasons. Among them: 1. White Pine concentrates yield extremely high matte grades (65+% Cu) and viscous slags. The viscous slags hinder matte settling causing matte "prill" entrapment in the slag 2. White Pine's total refined copper output is accomplished through fire refining requiring special techniques for impurity removal, especially small amounts of nickel introduced from purchased pyrite and chalcopyrite fluxes. These special techniques result in high-copper slags, refractory to smelting, being reintroduced into the reverberatory furnace. 3. Furnace bottom build-ups resulting in mechanical matte entrapment through the formation of "dams" hindering matte flow. 4. Occasional concentrate fluxing and furnace atmosphere control problems.

Jan 1, 1975

By Circe Verba, Scott Montross, Jon Yang

This work is a first-order study to assess the suitability of an organic acid lixiviant to extract rare earth elements (REE) from coal preparation fines refuse sourced from a Pennsylvania mine with a total REE of ~ 300 ppm. The extraction of REE using an organic acid, in this case 0.1Mcitric acid and 0.5Mtrisodium citrate solution, is compared against 0.5M(NH4)2SO4, 1MHCl, 1.2MH2SO4, and 0.5Methylenediaminetetraacetic acid (EDTA). Ashing the coal waste material prior to leaching tests with the citrate solution nominally improved REE extraction. Buffered citrate solution recovered 7% of the total REE in the as-received Isabella Fines as compared to 11% in ashed samples, whereas (NH4)2SO4 extracted 5–6%, respectively. EDTA recovered up to 33%of the total REE, most likely due to the higher coordination chelate bond. Mineral acids, however, outperformed the organic acids on ashed material (16–52%REE recovery), suggesting that organic acids may not be a suitable competitive option for REE extraction from these types of feedstocks.

Jun 15, 2021

By Patrick Doig, Ross Webb

The Bradshaw Section 5A Interceptor involves the construction of two miles of 108-inch, finished diameter tunnel in dry soils. Excavation is generally by Lovat TBM with ribs and lagging support. The tunnel is beneath a recreational parkway and stringent measures have been enacted to preserve the parkway and minimize disruption to the neighborhood. Apart from these constraints, the project would have been unremarkable but for the intervention of CalOSHA and the local fire department who ordered extraordinary fire protection measures. The paper discusses the cause and effect of these measures and comments on the potential repercussions for other projects.

Jan 1, 1999

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By Hans von Michaelis

It is appropriate that this opening session of HAZPAC '91 and Randol Gold Forum CAIRNS '91 should address the question of what the two industries can learn from each other. The panel is made up of members with experience in both industry. Several are experts on managing both hazardous waste and the mine/mineral processing environment. There is a marked difference in the regulatory needs with respect to treating and disposing of mining and mineral processing wastes, and "hazardous" or industrial waste materials. The topic of this paper is on the things that the two industries have in common: Many of the processes and technologies that are being used or are currently being developed for treatment of hazardous waste are the same or similar to the processes that have been used for decades or k,nger in the mineral processing industry. Hazardous waste treatment and remediation of contaminated solid and/or groundwater is a relatively new industry. Many of the practitioners in this new industry are relatively inexperienced in most of the "new" technologies that are being applied or developed.

Jan 1, 1991