Search Documents

By R. L. Hudak, R. F. Randolph, A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. The National Institute of Occupational Safety and Health (NIOSH) has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by nine decibels. The “Inquiring Ears Want to Know” fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By C. J. Pritchard

Controlled recirculation of ventilation air in underground metal and nonmetal mines has the potential to improve airflow and the health and safety of miners when implemented properly. Previous research by Robinson, Marks, Cecala and others concluded that the success of a district recirculation system is predicated upon an adequate supply of fresh air and the use of a reliable monitoring system for safe operation. This recent research also showed that contaminant levels will not exceed pre-recirculation levels, and that district recirculation can improve the dilution of face contaminants, especially methane gas. To illustrate the process of implementing controlled recirculation and also to promote and give guidance to mine operators in consideration of this tool to improve mine airflow, Office of Mine Safety and Health Research (OMSHR) researchers acquired baseline airflow and contaminant data from a multi-level room-and-pillar nonmetal mine and used commercial ventilation network software to simulate base case conditions and recirculation of mine air. Mine return air baseline contaminants of dust and diesel particulate matter were at lower levels than intake air, providing the potential for improved face air quality. A ventilation model implementing controlled recirculation was developed and analyzed, showing an increase in air quantity at the face, improved intake air quality, and contaminant exposure levels below those set by statutory requirements. These results, along with conclusions reached by previous researchers, provide the basis for examining the safe and effective implementation of controlled recirculation in metal and nonmetal underground mines using this mine as an example.

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By Cleland N. Conwell

The term "tender tundra" is a myth---a well-developed myth, but contrary to the fact. Any area that supports herbivores must have a plant base to supply food, In Alaska, herds of caribou migrate and live north of the Arctic Circle. And, if there is enough growth in the moss and lichens and arctic grass to support a caribou herd, the "tender tundra" can heal after it has been disturbed by mining. Another myth is that Alaska is an ice box. Actually, many areas In the state---particularly the Interior---have a high agricultural potential. Nevertheless, the fact remains: whether it is reclaimed by advancing the productivity from forest to agriculture or is allowed to remain a wild-life habitat, Alaskan land will revegetate. Reseeding speeds reclamation, but left to nature, native species will reclaim the land whether it was disturbed by forest fires, roads, villages, or mining. In fact, it is impossible to find many of the old gold mining camps.

Jan 1, 1975

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970's that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960's. In the early 1970's a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970's has therefore seen a very rapid pace

Jan 1, 1979

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By William Gleason

"Speakers and attendees of the 2016 Cutting Edge Conference could not be faulted for keeping one eye on the presentations taking place at the Hyatt Regency at LAX in Los Angeles, CA on Nov. 7 and 8 and another on the results of the historic election in the United States that took place on Nov 8. While there was certainly interest in the presidential campaign, there was also a great deal of interest in Measure M on the California ballot. Measure M, which passed easily, is a half-cent sales tax increase that will fund the most ambitious transit expansion in Los Angeles County history.In the coming years, the ballot measure will transform a traffic-choked region by funding the construction of nearly a dozen new rail lines with an estimated $120 billion raised in four decades. Among the projects that could come to fruition are a twin-rail tunnels project through the Sepulveda Pass and new connections in the city.During the update on West Coast projects, Bill Hansmire summed things up with a slide asking “How much work is there on the West Coast,” and his answer was “Billions.”From Seattle, WA south to Los Angeles, there is already a lot of work for tunneling and underground construction experts, and Measure M ensures that there will be plenty of work for decades to come.Currently, The Los Angeles County Metropolitan Transportation Authority (Metro) has three rail projects underway that were funded by Measure R in 2008 — the Regional Connector, the Purple Line subway extension and the Crenshaw/LAX Line that are designed to alleviate the traffic pressure with an eye to more solutions.Measure M is the fourth sales tax increase to fund transportation in L.A. County, bringing the base sales tax rate to 9.25 percent. In some cities, which already levy their own sales tax, the rate would be higher, The Los Angeles Times reported.About 35 percent of the revenue will fund major new transit projects, such as the subway under the Sepulveda Pass, extension of the Gold Line to Claremont, extension of the Crenshaw Line to West Hollywood and acceleration of the Purple Line Subway construction along Wilshire Boulevard to finish in 2024, 10 years earlier than scheduled.About 17 percent would fund a dozen highway improvement projects, such as widening parts of I-5 in the Antelope Valley and southeastern county, adding bus lanes to the Sepulveda Pass section of the 405 freeway and adding truck-only lanes to a section of the 710 freeway."

Dec 1, 2016

By M. P. Juszli

During the 1980's, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being trans-ported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to far-away customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable Just a few years ago.

Jan 1, 1989

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By Walter Küng

The Henderson Coarse Ore Conveying System is a three flight belt conveyor system transporting primary crushed molybdenum ore 24 km (15 miles) underneath the North American Continental Divide. One of the conveyors is 16.8 km (55,200fi) in length with 8,200 kW (11,000 HP) of installed power. The overland conveyor contains 11 vertical curves and 9 horizontal curves, some with radii as small as 1,500 m. he system began full operation in December 1999 and is one of the longest and most complicated belt conveyor systems yet constructed. he design of this conveyor system utilized many innovative engineering concepts including low-energy belt covers, low-resistance idlers, torque-controlled tail drives, combined gravity and active winch take-up systems, small radius horizontal curves and belt turnovers. his paper reviews the start-up of the system, discusses the success of the design and addresses the lessons that can be learned from the first 4 years of operation of this unique conveyor system

Jan 1, 2004

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By M. P. A. Hames, D. R. Beaumont

INTRODUCTION Legend has it that when Isembard Kingdom Brunel was confronted with the cost and consequences of one of his bridges having failed, he responded cheerfully that the event had saved investors and taxpayers a fortune because it prevented him from repeating the same design at several other locations. To meet the demands of rejuvenating and expanding the transportation system in an era of industrial growth Brunel and his contemporaries introduced bold designs and many innovations. Great advances in design and construction techniques resulted, yet these too had their practical limits as the story tells. In the gold mining industry today we face the same challenge of expansion, yet designers must respond mindful of economic restraints. Is innovation the answer? It has two meanings; to bring in novelties and to make changes. Distinguishing between improvement and novelties, or simply recognizing the benefits and limitations of new ideas over proven technology is part of good design. This paper will illustrate the practical aspects of selecting appropriate solutions to a design problem by examining a variety of examples common throughout the industry. Since a variety of engineering disciplines contribute to the design of a gold processing plant, and each has some old wisdom to impart or new development to boast this paper is divided into the different areas of expertise involved.

Jan 1, 1987

By P. Croney

Environmental monitoring requires major effort and expense but management of data receives less attention. A modem database system can manage hydrochemistry, water levels, meteorology, geology and downhole geophysics data and is flexible to allow the storage of ad hoc data. Reports can be customized by the user and derived data generated from input values. The production of high quality maps with contours and hydrochemical diagrams is an essential part of the reporting process. These maps integrate directly with the current site survey information. These facilities are best provided by storing the data in an industry standard database such as Oracle or Access to which customized AutoCAD and Microsoft Office routines make direct SQL calls.

Jan 1, 1997

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By Gunnar Thaning

The iron ores mined by LKAB in the north of Sweden have excellent beneficiation properties. This gives LKAB a favourable position as regards the production of low silica pellets for direct reduction. LKAB have concentrated on developing and marketing grades of pellets for the Midrex-Purofer-HyL process group, i.e. such D.R. processes which are carried out in a shaft furnace or a static bed using reformed natural gas as a reducing agent. The paper deals with properties and quality demands of iron ore pellets for such processes. Matters such as the effect of the residual magnetite in the fired pellets on the degree of metallization, the amount and composition of the slag phase in the pellets, the mechanism of the disintegration during reduction, the state of swelling of the pellets during the conditions prevailing in these processes, the importance of the porosity, the improvement of the reducibility and lowering of the sticking tendency of the pellets by small additions of suitable additives and the influence of the pellet size are discussed. A special test procedure for D.R. pellets has been elaborated by LKAB. Thus, three metallurgical properties are routinely determined separately, namely reducibility, reduction strength and sticking. The test methods are described. Finally the present and future LKAB pellets for direct reduction are presented with respect to chemical analyses and metallurgical properties.

Jan 1, 1978

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non-bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30% and 50% alunite between 50% and 70% quartz with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone and a chlorite-montmorillonite zone. Total U.S. reserves of alunite were estimated at 20 million metric tons (at 30% alunite) by the U.S. Bureau of Mines in 1941. Here recent work by the U.S. Geological Survey estimates reserves of 252 million metric tons and potential resources at 1.4 billion metric tons. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves at these properties are estimated to be about 650 million metric tons. Inferred reserves are estimated at 2.5 billion metric tons and potential resources at 8 billion metric tons. It appears that the U.S. has sufficient reserves and resources for alunite to be considered as a potential non-bauxite source of alumina.

Jan 1, 1980

SOLUTION MINING Solution mining techniques present a means of extracting soluble ores, particularly such materials as salt and potash, from horizons which are not accessible by conventional mining. In the process of dissolving materials, it is evident that solution may be complete or partial. In general, the solution mining operations described in the following section relate to complete solution of the desired compound. Even though the solution of material is complete, there may be instances in which insoluble material is present to a large extent either as granular separated particles or as insoluble layers. The process required for obtaining the desired product involves access wells to reach the deposits, sufficient water supply to yield the production goals, and the development of an underground cavity. The process of solution mining, therefore, depends to a great extent on three factors: availability of a relatively pure strata or formation of salt or potash to be mined, access well or wells, and adequate control of the solutioning process so that enlargement of underground cavities can be fairly well delineated. Since halites represent the most general ores mined by this procedure, the considerations which follow are based primarily on the production of sodium or potassium chloride. The producing formations may be in the form of bedded evc~porites wherein the salt member may be some 30 to 500 ft thick or from salt domes in which great depths of salt occur. Solution mining has been carried out to depths of nearly 10,000 ft. The recovery of saturated brine from wells drilled to effect the solution-mining process leads to further processing. In many instances, the procedures are relatively simple and involve simple recrystallieation or fractional crystallieation, while in others more complex flow systems are required before a final product is obtained. The intent of this section is to provide information relative to the basic procedures for obtaining materials which are soluble in water and to acquaint the engineer with the various aspects of the overall problem which in many instances, may become quite complex and present numerous difficulties. The storage of fluids, particularly hydrocarbons, underground has proven to be a very important part of industry operations. Cavities formed in salt provide excellent storage facilities. The formation of well-defined controlled configurations of such cavities has been possible because of better understanding of the solution process, wide experience gained over nearly 30 yr, and improved technology in drilling and completing wells, surveying caverns, and the operation of numerous types of systems. Solution mining techniques will improve in the future. Many facets of the simple operation of pumping solvents and extracting valuable minerals require further study. Developments undoubtedly will occur to further the processes of mining by solution. In addition to those whose names appear in connection with the individual subjections which follow, a major role in assembling and processing the material in this section was played by Dr. D. A. Shock, Central Research, Continental Oil Co., Ponca City, Okla.

Jan 1, 1973