Search Documents

By A. Bhargava, V. Nasri

Traditionally, secant piles have been utilized to provide temporary support during excavation for shafts and cut-and-cover tunnels. As an alternative, the secant piles can be included into the permanent structure, where they serve as the envelope sustaining the lateral loads and gravity of the permanent structure in addition to supporting the excavation during construction. This has several benets, such as shorter building times and lower excavation costs. Recent construction of an approach structure and an underground station as part of Montréal, Canada’s Réseau Express Métropolitain (REM), one of the biggest transit systems in North America, was completed with remarkable success using this. In this paper, a case study based on a project that employed secant piles as the permanent liner is presented. Techniques to guarantee a watertight construction with over a century of service life are described, along with a variety of structural and waterproong methods applied to create an economical design.

Jun 23, 2024

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969

By Muhammad Hashim Rasa, Ali Aras

Recovering valuable metals from tailings not only provides a source of income but also helps conserve natural resources, thus reducing the environmental impact of mining activities. This study aimed to recover cobalt using tailings of the Küre flotation plant, which were determined to contain 0.17% Co. Flotation tests were conducted on samples taken from the tailings to investigate the effects of pH and pH conditioning time, as well as types and amounts of depressant, collector, and frother on the grade and recovery of Co in rougher flotation tests. Optimal flotation conditions were determined to be pH 6, a pH conditioning time of 7 min, and dosages of 50 g/t, 100 g/t, and 20 g/t of sodium hexametaphosphate, X-231, and DF250, respectively. According to the rougher flotation test results, a concentrate with a Co grade of 0.46% and a Co recovery of 84.15% was obtained. In the concentrate obtained using cleaner flotation tests, the Co grade increased to 0.49% and Co recovery increased to 90.56%. These results show that froth flotation, carried out with the appropriate reagents, is a successful method for recovering Co by enriching the flotation plant tailings.

May 17, 2023

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By K. N. Han, H. C. Cho, R. Kim

"As an extension of the work on the effect of OH- on various cations in hydrometallurgical systems, the effect of Cl-, Br-, I- and CN- on cations such as Ag+, Cd2+, Hg2+, Cu+, Cu2+, Co2+, Zn2+, Pb2+ and Sn2+ has been examined in detail. The Newton-Raphson technique has been used to determine the amounts of various metal species as a function of the concentration of anions. Some practical implications of various metal complexes in metal separation and removal from solutions have been examined and discussed.IntroductionUnderstanding the role of anions in hydrometallurgical processes often determines the success of an operation. The successful choice of concentration and type of anions not only leads to an effective extraction and removal of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2009; Al-Tarazi et al., 2004), but also to assisting effective separation of various metals, whether it is a solvent extraction, ion exchange operation or even a simple precipitation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974).This paper continues the discussion of the role of anions in hydrometallurgical systems beyond the role of OH-, which was the topic of a previous paper (Kim et al., 2014). Table 1 lists various anions that are frequently used in conjunction with metal ions to be selectively separated or precipitated. As seen in the table, many anions are used frequently in hydrometallurgical practices. Some of the more frequently used anions include OH-, SO4 2- and CO3 2-. The halogen elements, Cl-, Br- and I- , as well as CN-, are also used in hydrometallurgical applications, especially in relation to noble metal recoveries (Meng and Han, 1994; Zhang et al., 1996; Sun et al., 1996; Starovoytov et al., 2007)."

Jan 1, 2015

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By Salvatore] [Parand

Deep well disposal is a much used and abused term which is the panacea for wastewater disposal in some minds and creates near hysteria in others. It can be the answer to a difficult waste disposal problem, or if improperly employed, can create more problems than it solves. My purpose in this presentation is to focus on the value and limitations of deep well disposal as expressed by New York State's experience and policies. To he sure, I feel a place for such practices docs exist if adequate safeguards are utilized. I shall give a broad brush approach to New York's legislative, geologic and operational concerns and speak briefly on some case histories. I shall not delve deeply into the technological details since I am not an expert in mining exploration or well drilling.

Jan 1, 1973

By Paul G. Mahoney

The original Radum aggregate plant, built by Henry Kaiser in 1931, is the oldest of the nearly 200 individual operations established by the Kaiser companies. Since that time it has been producing aggregate products primarily for the San Francisco Bay Area. Currently, and for many years, this plant has been listed as the Nation's No. One aggregate producer. Early this year a new $10,000,000 facility went on line replacing the old plant. Construction of the facilities was performed under the direction of Kaiser Engineers construction management teams. The existing plant continued to operate without interruption during the entire construction period.

Jan 1, 1970

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By J. R. Muhm

Environmental due diligence investigations, also known as Phase I Environmental Audits, are increasingly important to major investors, venture partners, or prospective purchasers or sellers of mineral properties. Knowledge of environmental risks associated with a property will allow better appraisal of a property's overall desirability prior to completing the transaction. It is possible that the cost of environmental cleanup could exceed the value of the property. Topics appropriately investigated include permit status, water quality, past use of the property, hazardous materials management, storage tanks, public records pertaining to the environmental character of the property, and environmental costs.

Jan 1, 1991

By K. A. Natarajan, M. R. Sabari Prakasan

"Biodegradation of sodium isopropyl xanthate using two types of bacterial strains, Paenibacillus polymyxa and Pseudomonas putida, is demonstrated. At concentrations higher than 50 mg/L, the presence of xanthate in the growth medium resulted in bacterial toxicity, retarding growth kinetics. Adaptation through serial subculturing in the presence of higher xanthate concentrations resulted in the development of xanthate-tolerant bacterial strains. Stress proteins secreted by bacterial cells grown in the presence of xanthate were isolated. Bacterial cells could utilize xanthate as a growth substrate, degrading xanthate species in the process. Acidic metabolic products generated by bacterial metabolism promoted efficient xanthate decomposition. Probable mechanisms for the biodegradation of isopropyl xanthate are illustrated.IntroductionDifferent types of alkyl xanthates (ethyl, isopropyl, amyl, etc.) have been used as flotation collectors in the concentration of sulfidic ores for several decades. Large quantities of waste water and xanthate-containing effluents are generated by ore flotation processes, posing considerable environmental challenges. Billions of cubic meters of such process waste waters are produced annually across the world, most of which are discharged to the environment, often without any treatment. Leakages and accidental release of xanthate reagents from manufacturing plants and during transportation and storage can also contaminate the environment. Residual concentrations of xanthate reagents are encountered in waste effluent, which are found to be toxic to aquatic life and unfit for human consumption (Harris, 1984; Okibe and Johnson, 2002). Further, direct recycling of such waste waters for plant operations can compromise water quality standards required for process operations. The presence of residual xanthate in recycled waters from flotation plants deleteriously influences flotation processes. Xanthate can be easily decomposed at low pH values; however, CS2, which is more toxic, will be produced by the acidification of neutral and mildly alkaline xanthate-containing solutions. Physico-chemical methods such as flocculation, chemical oxidation and decomposition and physical adsorption used to remove residual collector reagents from mill process waters are often expensive and not environment-friendly (Oliveira and Rubio, 2009; Cheng et al., 2012; Molina et al., 2013,)."

Jan 1, 2015

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

It took me nearly nine months to make the move from Arizona to Berkeley, opening an office and planning our new home. While I was in Warren Dorothy had rented two rooms for my office In the new California Commercial Union Building at 315 Montgomery Street in San Francisco. She made such a good choice that this remained my address for more than 50 years Dorothy had also looked over many lots In Berkeley, and took an option on the one that pleased her the most. It was a beautiful lot, or rather three, as we took three lots to protect our view. The only possible drawback was that it was in a new district and there were only two houses within two blocks. No one could tell how the area would develop but we liked it so much that we bought the lots on the spot and signed a note to guarantee payment. Dorothy's good judgment was shown by the fact that after 50 years we are still glad to be living on the same property, at 168 Southampton Avenue. We arranged a meeting with the distinguished architect Bernard Maybeck-and employed him to design a house for us. Dorothy spent most of her time with Maybeck planning the house and an attached studio for her, and she later wrote an amusing essay on her dealings with Maybeck. They were so successful that even now we could not think of any changes we would have wanted. It took several months to design a house that suited Dorothy and would fit on our hilltop. I was glad to overcome some of Maybeck's scorn for "only an engineer" by showing how, by rotating the studio addition 45º, it would fit the lot without serious excavation. We finally signed a contract with Maybeck, borrowing so much money that it scared us. First Consulting After short jumps to the gold mines in the Secret Pass District near Kingman, Ariz., and to the Espiritu Santo prospect adjoining the rich

Jan 1, 1976

By D. Tao

Reverse cationic flotation is the most widely utilized flotation method for concentrating iron ore. In this process, quartz is often floated with ether amines (R?(OCH2)3?NH2) partially neutralized with acetic acid. However, it is well known that the cationic flotation of quartz does not work well if a certain amount of slime is present in the ore slurry. To improve flotation performance, starch is often added to the flotation feed to selectively flocculate and depress the iron minerals and sodium silicate is used to disperse the silica gangue. The present study was conducted to improve the efficiency of iron ore flotation by the use of a new type of depressant for clay and iron minerals, Georgia Pacific (GP) clay binder. The GP clay binder minimizes slime adsorption on quartz and hematite particles by agglomerating clay particles to reduce their surface area. It also helps depress hematite flotation due to its unique chelating action on iron ions. The results from this study show that the GP clay binder is an effective depressant in iron ore flotation. When it was used as a substitute for corn starch, it increased concentrate grade from 60.78% to 67.67% and increased iron recovery from 71.96% to 72.90%. The combined use of GP clay binder with corn starch produced even better flotation performance, increasing iron recovery to 78.15%, while the concentrate grade remained stable at 67.08%. Keywords: Georgia Pacific clay binder, Iron ore flotation, Flotation efficiency

Jan 1, 2010

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Jan 5, 2023