Search Documents

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2' diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques have been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

Feb 23, 2014

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By H. Cho

There is an indication that high-pressure roller milling promotes selective liberation due to preferential breakage along the mineral boundaries. A study was undertaken to compare the degree of liberation obtained by high-pressure roller milling with that of conventional ball milling. Coals with different HGI's were ground in a high-pressure roller mill and a ball mill to produce products with similar size distributions. The products were then subjected to float-sink separations to determine the degree of liberation. Also, the relative cleanabilities were compared by separating the ground products by froth flotation. The results from this study are presented in the paper.

Jan 1, 1994

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Martin Herenknecht, Michael Knabe, Ulrich Rehm

In Switzerland at present, the longest railway tunnels in the world, the Gotthard(57 km) and the Loetschberg base tunnel (34km) are under construction. For thischallenge six high-tech HERRENKNECHT Hard Rock Tunnel Boring Machines (TBM)are applied, which have to excavate approx. 80 km at the Gotthard and 20 km at the Loetschberg Tunnels. The machines being used are of a single Gripper-TBM type, which are equipped with the latest rock support techniques, in order to optimize the quality of the working conditions for the personnel which have direct impact on the quality of the tunnels. The different requirements of the projects based on different speci?cations within the tender documents led to completely different TBM concepts which will be reviewed in detail in this paper.

Jan 1, 2003

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By George M. Potter

Under contractural arrangements with the Bureau of Mines, Mountain States Research and Development, Inc. (MSRD) completed a technological investigation to determine the feasibility of in situ mining of metal commodities other than copper and uranium, The study was based upon available literature and experience. The selection of potential candidates for in situ mining was influenced by economic importance, probable amenability to in situ methods, and environmental considerations. Four metals (or metal pairs) were chosen for feasibility studies: aluminum (with a copper byproduct), gold-silver, and manganese were recommended for further study and action; cobalt-nickel was also recommended contingent upon preliminary laboratory leaching and recovery investigations and field geohydrological work. Mining and recovery plans and an economic evaluation are included. Other metals with potential for in situ leaching are lead/ zinc, molybdenum, and vanadium.

Jan 1, 1981

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By M. A. Evanto

Since the late 1970's, the Roof Control Division (RCD) of MSHA's Technical Support has been performing linear analyses for the enhancement of miners' safety. This remote sensing process uses Landsat data to predict areas of potentially hazardous ground conditions in underground mines. To date approximately 700 analyses have been completed by the RCD, with nearly 75 being performed with the current equipment, software and methodology which was updated in early 1995. While success is difficult to measure, requests for linear analyses continue to come from large and small mining companies which suggests the industry's acceptance of the process.

Jan 1, 1998