Search Documents

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By Peter W. Lipman

In the Rocky Mountain region, variations in Tertiary mineralization correlate with changes in tectonic setting and associated igneous activity that can largely be related to tectonics along the west boundary of the American plate. Successive settings include compressional tectonics and associated continental-arc igneous activity; transitional igneous types associated with intra- and back-arc extension; and basaltic or bimodal basalt-rhyolite assemblages associated with Basin and Range extension in- ward of a growing transform boundary between Pacific and American plates.

Jan 1, 2013

By J. J. Gusek, J. T. Gormley, V. Scovazzo

Glenrock, WY is underlain by two abondoned coal mines. Subsidence events have been recorded over the years, with the frequency increasing in recent years. As part of Wyoming's Abondoned Wins Lands Program, investigations including mining history/methods/mappings, subsurface drilling and material site searches were performed. Portions of the mines less than eighty feet from the surface, were identified as probable for subsidence. Subsidence control by hydraulic backfill was selected. Design included search and injection boreholes, water supply from the mines and the slurry mixing, transport and injection system. Injection system performance and backfill success is king monitored during construction.

Jan 1, 1986

By Douglas F. Stevenson

Your committee doesn't assign any easy topics to us speakers. How do you define "successful" in what is essentially a losing game? I am reminded of the fellow who returned from a one-week vacation in Las Vegas, and proudly stated, "I only lost $150." To him, that was "success." I am afraid that workers' compensation is a losing game for employers, too, and success has to be defined in terms of how much or how little is lost. We have no chance of producing a profit for our employer. We will narrow down to some suggestions about conducting a workers' compensation program at the plant level, but first I want to discuss the general legal, social and legislative climate in which your plant program operates. Workers' compensation is a statutory program with its general parameters established by the legislature. These parameters are then amplified by the boards and commissions established to administer workers' compensation. What influences the legislature and the boards and commissions as they establish the framework in which we must function?

Jan 1, 1986

By J. H. Kim

Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, there have been numerous developments in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method, and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks, but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method, and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991).

Jan 1, 1992

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By Chee Theng

"Mining professionals are a resilient lot. Sure, copper prices are dismal, permitting processes seem interminable and the top mining companies are shedding jobs like a Shetland sheepdog sheds hair. All the more reason to hone technical skills, reconnect with old contacts and get one’s finger on the pulse of the industry.More than 400 did just that in the balmy sunshine and among the saguaro cactus of the Tucson venue of the SME Arizona Conference.Giving the keynote speech was Patrick Merrin, vice president at Hudbay Minerals (see box), while the luncheon speaker was University Distinguished Professor Mary Poulton, director of the Lowell Institute for Mineral Resources at The University of Arizona.“Attendance was great, especially given the copper price,” said Ta Li, vice president of business development at Tetra Tech and 2001 SME President. “The luncheon speaker was one of the better ones in recent years. Her talk contained a lot of fresh ideas, and practical versus theoretical concepts.”Talk about values, not economicsPraise was unanimous for Poulton, who gave a thought-provoking talk on “The New Face of Mining: The Culture Change for Compatible Mining.” Corporate social responsibility has been embraced by the metals mining industry, and it’s being done right, she said. “So why do we have more conflict? Why are there more protests? Why does permitting take longer and longer?” Poulton made a case for an approach based on compatible, rather than sustainable, mining to present a new face of mining that can be compatible with communities, cultures and the environment, and still be profitable. When the mining industry starts to talk about compatibility between what it is doing and what “me,” as the consumer, wants, what “we,” as citizens of a community, want, and what’s good for the “world,” we’re going to see the next culture change happen, she concluded."

Jan 1, 2015

By James J. Scott

I am indeed honored to be the 1991 recipient of the Daniel C. Jackling Award. To be voted this honor by my peers in the Society for Mining, Metallurgy, and Exploration and AIME means more to me than I can truly express. Daniel Jackling's position and prominence in the mining industry first came to my attention in the fall of 1949 when I transferred from Wisconsin Institute of Technology, then a three-year school, to the Missouri School of Mines to complete my last year for a bachelor's degree in mining engineering. I played basketball in the Jackling gym and ran track on the Jackling field. I didn't know a lot about Jackling then, except he was an honored graduate of the school and, obviously, supported the school financially. Over the years, Jackling's name kept coming up. He was a man with a reputation for being a doer, a mining leader who was always a step ahead, a mining engineer who knew how to motivate men in the working place, to organize mining systems, to finance and organize corporations. to open up new, low-grade ore bodies for exploitation. If Jackling were alive today, I would expect he would bean excellent candidate to apply practical rock mechanics to his projects. Looking over the list of Jackling Award recipients, I have known many, have met many personally and had a few who were dear friends that affected my own professional life. Ab Shoemaker, '58, and I consulted at the White Pine Copper Co. on mining problems in the 1960s. We arranged for our visits to the mine to coincide so that we could collaborate on our ideas. I would rent an auto and drive for Ab. He said he was the only mining engineer in the country that had a PhD for a chauffeur. James Boyd, '67, was my mentor as regards the White Pine Rock Mechanics Program that we organized in 1963. Only through Boyd's forsight. leadership, dedication and willingness to spend money on research and development did the Practical Rock Mechnics Program at White Pine succeed. He never wavered in his support to that program or to me personally. Tom Howard, '75, was my predecessor in 1970 as Director of Mining Research for the US Bureau of Mines. When I joined the Bureau in August 1970, he had the research centers up and running. Any successes I may have had with the Bureau of Mines were due in great part to Tom's leadership and organization throughout the 1960s. Gene Cameron, '68, was my teacher at the University of Wisconsin and I remember him fondly. He was the one professor who lectured in a manner that made me welcome going to his classes each day, a truly remarkable educator. If you have come today to listen to me talk about instrumentation, rock properties, stress-strain relationships, rock mechanics theory, etc., you will be disappointed. Large volumes of data have been collected by well qualified theoreticians to define stress-strain conditions in mines. Unfortunately, very little of this data has been used by industry due to the lack of initiative and understanding by the researchers to the true problems of implementation in the industry. I hope my remarks will assist future investigators to work through the maze of operational problems so they will experience the satisfaction of seeing their research used. I fully realize that the Jackling Award is given by the Society for Mining, Metallurgy, and Exploration and is primarily offered for accomplishments in hardrock mining. I have found it impossible to separate hardrock and coal mining when I talk about "Applied Rock Mechanics." There is too much overlap and the same mechanics principles are applied to both. For example, coal mine designs have been applied to salt, trona and potash. Also, the original layout and design of White Pine Copper Mine was based on coal mine designs. Any developments to apply rock mechanics ideas must

Jan 1, 1992

By Steve Kral

As the mining industry watches commodity prices continue to soar, the question on most everyone’s mind is how long will this upcycle last. The con-census among speakers and attendees at the SME Annual Meeting and Exhibit is that this cycle is sustainable. The buzz at the meeting was, of course, the current boom cycle the industry is in. Most agree that China’s huge appetite for mineral commodities is part of the force driving the upturn. But the improving economies of other developing nations also plays a role. However, along with the good times come challenges. Speakers at the keynote session addressed some of the challenges and offered their opinions on the sustainability of the boom.

Jan 1, 2006

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By K. Fountain

In Novemeber of last year I visited a mica mine in Hunan Province, China. For nine months , we had been trying to sell Chinese mica to a customer in Belgium. Talking to the customer was like negotitating with a stone wall. The buyer refused to communicate any -thing other than his steadfast refusal to consider Chinese mica. He would not advise us what he wanted, what specifications or grades. He would give no indication if our price at market, or reasonable, or totally out to lunch. He would not even accept samples. It took no genius to guess that the mica buyer had at some time in the past bought a shipment of Chinese mica and had received a disaster. I invited the mica mine in Hunan in order to see for myself what could be done - without massive investment in equipment and instruments - to upgrade the quality of the mica for export. We had seen this type of customer reaction before. One disgruntled customer who had pur¬chased pigment grade barites direct from China ranted and raved about unreliable and inconsistent quality. It did no good to explain to him that China is a big country, with hundreds of mines scattered throughout many areas, each producing a different product. Our further explanation that Chinese export organizations also varied in degree and efficiency of customer service fell on deaf ears. Samples had no effect on his perception. Eventually we showed him photoraphs of two mountains of pigment grade barites. One lot was our sales of pigment barites to a major European minerals processor. Our Chinese barites stood proudly white and beautiful next to a hill of other material which now appeared at best mediocre and dull by comparison, and which the buyer had decided to reject after he received our Chinese barites. Finally the customer was sufficiently impressed to look seriously at our guaranteed specification and the outturn analysis performed by our other customer.

Jan 1, 1987

By K. Kim

A site characterization strategy formulated for the probabilistic design of underground structures is presented, which takes into account the variability of rock properties and the stochastic nature of the rock failure process. It entails determining probability distributions of rock properties by utilizing the theory of extremes and Monte Carlo simulation. Laboratory and field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass properties can be estimated using empirical relationships currently available. This results of analyses can be incorporated into the design of underground structures, and then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1995

By Georgene Renner, Chee Theng, William Gleason

"With more than 900 booth spaces sold and 630 exhibiting companies displaying their wares, there was something for all 7,804 attendees on the exhibit floor of the 2015 SME Annual Conference & Expo in Denver, CO Feb. 15-18. The following is a sample of what was offered at the 2015 meeting.3D Laser MappingData collection and data analysis are changing how mining is done. One field in which technological advancements have made safer and more efficient operations possible is through site and slope monitoring.3D Laser Mapping, a United Kingdom-based company, was on hand at the 2015 SME Annual Conference and Expo to display its solutions for the mining industry, including its SiteMonitor4D system.The state-of-the-art laser measurementbased system was developed in partnership with geotechnical engineers and mining surveyors, and is a simple-to-use, reliable solution that has the flexibility and performance to function in a range of monitoring applications.The system measures and monitors the stability of rock faces, landslips and man-made structures, including ongoing, periodic measurement of volumes - stockpiles, cutbacks and waste dumps and has high-speed laser scanning for regular mapping of large areas by mounting the scanner on a vehicle.With specifications that other monitoring techniques cannot achieve, laser scanning opens up a new dimension in mine measurement and monitoring.www.sitemonitorsystems.comA.R. Wilfley and Sons Inc.Founded in 1919, A.R. Wilfley and Sons Inc. has been manufacturing dynamic-seal and static-seal pumps in Colorado for nearly 100 years, delivering its high-reliability, low-maintenance, heavy-duty process pumps and slurry pumps to the global mining industry. The family-owned company is now in the hands of the fifth generation."We are the dynamic-seal experts," regional sales manager Cesar Murillo said. "Most other companies are unable to do 100 percent dynamic seals and have to use mechanical seals or packing," he said, but Wilfley’s sealing technology does away with the need for mechanical seals and packing and their associated problems. As a result, solids and slurry handling capabilities are high, the pump can be run dry, and product dilution is eliminated. The pump can tolerate more misalignment, more cavitation, and more vibration in the pump during operation."

Jan 1, 2014

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By H. Kinilakodi

The authors previously had developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the Safe Performance Index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency, or MSHA in recognizing and addressing emerging problems with actions that may have been able to prevent high-risk conditions, the fatality, and/or other serious injuries. The approach would have given scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012