Search Documents

By Todd L. Hollingsworth, Jeremy K. Hobbs

In 2001, the Radomiro Tomic Mine located near Calamq Chile, added a tertiary crushing facility. An 84" wide mobile tripper is used to fill their tertiary crushing storage facility. This paper is a we study to demonstrate the drive and control systems in use on the tripper. Of special note is the design concept used to allow the system to operate multiple motors in both demand and regenerative modes through a single VFD. Also noted is the use of touch screen local controls, handheld radio controls, starting/stopping/ braking philosophies, safety device interfaces, and the local to remote control interface.

Jan 1, 2004

By S. W. Thomas

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value .are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A) A relatively large size sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B) When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves.

Jan 1, 1985

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By Fathi Habashi

A LARGE number of metals are found in nature, in rich deposits, in the form of sulfides as shown in Table 4.1. Treatment of sulfide ores is done mostly by pyrometallurgical operations; it is only recently that hydrometallurgical processing started to compete with pyrometallurgical methods.

Jan 1, 1970

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

By M. G. Karfakis

This paper examines the chimney occurrences in the Hanna Coal Field, Wyoming. Chimney caving is defined, previously proposed mechanisms involved in the development of a chimney are critically reviewed, and factors controlling chimney cave are identified. The main portion of this paper deals with the identification and characterization of chimney subsidence due to underground coal mining in the Hanna Mining District. In an attempt to characterize the subsidence, sink-hole occurrences are correlated with the depth of coal, thickness of mined-out beds, mining methods, nature of overburden, structural geology, and hydrology. Most sinkholes in the Hanna Basin appear to be conical in profile, with the apex upward. The average diameter is 15 meters (50 feet), with an average depth of 11 feet. Most have developed above an overburden of less than 61 meters (200 feet). The average mining height to width ratio is 5. Much of the chimney development is governed by the thickness and character of the overburden, the width and height of the mine opening, and the in situ state of stress.

Jan 1, 1986

By Ernst Raphael

Mechanical drives of belt conveyor drives have experienced a huge amount of improvements concerning technology, manufacture and product structure that reduced investment and maintenance cost significantly. Most of these improvements were of technological nature in the'70s and '80s of this century; whereas, the present decade requires products that meet technical excellence as well as commercial advantages such as quick delivery, low cost and reliable spare parts supply. The best approach to meet these requirements is a highly modular and standardized system of reliable components that cover all demands a conveyor drive might require.

Jan 1, 1998

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By James E. McTurk, Sheldon B. Bland, Roger E. Melley

During the first fifteen years of operation at the Syncrude facility in northern Alberta, numerous improvements have been made in the field of ore conveying. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about with the use of detailed field evaluation. This paper outlines some of the programs which have been run to optimise belt and system construction, and conveyor performance and utilization.

Jan 1, 1993

By Shamsuz Zaman, Barry Hansen

The major development in the evolution of the conventional subaeration flotation machine has been the steady increase in the size of the individual units. In 1950, large machines were of 1.35 m3 (48 ft3) volume capacity. In 1989 the largest volume capacity operating is 85 m3 (3,000 ft3 ) These improvements have enabled the mining industry to operate successfully in the face of declining ore grades and adverse metal prices. This paper describes the design features and performance characteristics of a number of significant flotation machine designs.

Jan 1, 1989

By Cheryl M. McInnes, Graham J. Sparrow, James T. Woodcock

Three composites, assaying about 3 g/t Au and 0.75% Cu, were investigated. Each contained oxide copper minerals, iron oxides, and silicates. One composite also contained copper and iron sulphides. Maximum gold extractions by thiourea leaching were obtained after copper removal by acid pre¬leaching at pH 1.5 and redox potentials of 400 mV (Pt versus SCE). Best thiourea leaching conditions were pH 1.5, redox potentials over 200 mV, and 0.4% thiourea. This gave 90% gold extraction in 2 h with thiourea consumptions of 25 kg/t. Lower potentials gave poorer extractions. Ferrous iron additions before leaching halved thiourea consumptions. Longer leach times and the presence of sulphide minerals sometimes resulted in reprecipitation of gold.

Jan 1, 1989

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By Janusz S. Laskowski

The most important type of potash ores, sylvinite, contains sylvite, halite and a small percentage of insoluble gangue [sulfates (anhydrite), carbonates (dolomite), and clay minerals]. Primary normal long-chain amines are exlusively utilized to float sylvite from halite, but since mines are also adsorbed by insoluble slimes, the process requires prior desliming. This is carried out either by mechanical means, or by flotation of slimes and blocking off the adsorption centers on clays with the use of polyelectrolytes. Fractional crystallization is employed to produce fertilizer grade KC1 from disseminated ores with a high content of slimes. An extender oil is needed in addition to mine to float coarse sylvite fractions. The process is carried out in a saturated brine at mine concentrations exceeding the solubility limit and is strongly affected by temperature fluctuations. All these important features, which make this process differ from a conventional flotation, result from a high electrolyte concentration.

Jan 1, 1994

Unless otherwise indicated, pounds are US avoirdupois, feet are US, and gallons are US.

Jan 1, 1985

By Tsuneyoshi Funazaki, Takayoshi Nakamura, Keizo Miki, Takashi Imaishi

The underground portion (about 10 km) of Tokyo Wan Aqua-Line consists of eight shield tunnels connected with Kawasaki Man-Made Island in between, at four underground locations. The connection work had to fulfill strict precision and safety requirements in the ground about 60 m below soft seabed, but was completed successfully in May 1997. This report describes the connection work in detail, featuring the method of investigating shield machines’ relative positions, ground freezing method and connection mechanism and procedures. It also mentions the present state of Tokyo Wan Aqua-Line that was put in service on December 18, 1997.

Jan 1, 1999

By H. Para, A. Aguirre, G. Artadi

Mining is a very important economical activity in Peru which has been recently developed without considering environmental aspects. Here, we show an experience at the Milpo mine, situated 4,200 meters above sea level; a mining company that has the value of being one of few from the last decade that is engaged in consolidating a model of environmental protection. The model includes aspects of contamination prevention and control, with bioindicators such as pasture cultivation, vegetables, forests, and hydrobiological species breeding. Socially, through means of development programs in natural areas, forestation and support to rural agriculture, together with environmental education, it is being demonstrated that it is possible to ensure tangible results in environmental conservation and the well-being of the populations around the mine.

Jan 1, 1998

By David Williamson

In the post-World War II years, metals analysts and statisticians have tracked the demand for metals in line with changes in Organization of Economic Cooperation and Development (OECD) industrial production (IP) growth rates, Williamson said. This was because the correlation between IP growth and metal demand was reasonable. "However, the correlation was exaggerated," he said. During times of expanding IP growth, metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked to reduce costs. Nonetheless, he said, a reasonable correlation could be painted between IP growth over the longer term and metal demand. "Yet, although this correlation has stood well since the last world war, it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, lately including Japan," Williamson said. The so-called "developing world" had been of little consequence. The Soviet Union and other communist bloc countries were deemed to be closed, self-contained entities that, for each metal, would either be net exporters or importers, he said. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated, Williamson said. It does not take into account the worldwide political changes that have occurred since the collapse of communism and the revitalization of China. "It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs," he said, including the western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are attempting to satisfy the expectations of the great mass of the world's poorer people, Williamson said. Such people, usually located in Asia, Africa and Latin America, have aspired to the same standard of living as people living in western Europe, North America and Japan. "Now, with free market forces at work, their aspirations will start to be met." Consequently, the demand for metals and other raw materials will now rise at a much faster rate. The production of raw materials has to keep pace with rising IP in the developed world. It will also have to keep pace with the demands associated with the rising expectations of increasing populations in the developing world, as well as from within the old communist bloc countries.

Jan 1, 1997

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulphide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular S02 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, i.e., pyrrhotite, pentlandite, pyrite, chalcopyrite and violarite, have agglomerated and reacted to form two intergrown phases: pyrrhotite solid solution (FeO.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu 0.03S). Magnetite formed euhedral crystals, skeletal crystals and dendrites at the margins of the matte. Prismatic, ferrohypersthene and octahedral Mg-Al-Fe spinet crystals and dendrites are present in the glassy slag. Key words: Nickel sulfide concentrate, Iron silicate slag, Bath smelting, Mineralogy, Microscopy

Jan 1, 2003

By Lawrence M. Brennan

Early in 1971 the Peabody Design and Preparation group began engineering on a preparation plant which was to process eight mil- lion tons per year of raw coal. For the first five or six years this product was to be furnished 50% from surface mining operations and roughly 50% from underground operations. By early 1980, 1008 of the production was to come from underground mines. Because of the large annual commitment from Randolph Preparation Plant, it was essential that the plant operate with minimum down-time. As usual, capital costs were to be kept at a minimum. Before we discuss the details of design, it would be best to discuss the overall picture. Underground production to be pro- cessed through Randolph Preparation Plant was to be delivered by means of one mile overland conveyor from Baldwin #1 Underground Mine to the plant. Surface Mine production was to be delivered by means of 100-ton haulage units dumping in a 1,000-ton capacity hopper. Because of the changing production rates in both the underground and surface mines as well as the great difference in size consist, it was decided that it would be necessary to divorce the plant as much as possible from production. For this reason, twin 6,500-ton raw coal silos were constructed to separate the two coals as well as allow blending. The preparation plant itself, was to be designed to Operate two shifts per day, five days per week, at an average rate Of 2,200 tons per hour with a maximum rate of 2600 to 2800 tons per hour. Coal was to be delivered to our customers by means of rail haulage at both unit train rates and plant process rates. The surface mined coal, after discharging into the 1,000-ton R.O.M. hopper, is fed by means of two 72" wide reciprocating feeders onto a 72" wide steel cable belt. The steel cabled conveyor discharges the R.O.M. coal onto a fixed grizzly, scalping out a percent of the 6 x 0 coal. The balance is fed to a 12' x 27' Rotary Breaker. The material passing through 6" round hole screens is added to the 6" x 0" from the scalping screen. The 6" x 0" is conveyed to the top of one of the 6500 ton silos designated for surface coal. Material that is not broken to pass the 6" breaker screen is discharged to a bin and disposed of with plant refuse.

Jan 1, 1976