Search Documents

By Martin L. Smith

Sampling and subsequent geostatistical structural analysis is being carried out on the Bunker Hill Superfund site in northern Idaho's Silver Valley. This paper reports on the findings and methodology used in the initial sampling campaign which had the goal of determining an appropriate sampling grid design, spacing and protocol. Emphasis is placed on those characteristics, of mine wastes which are unique and require special consideration when applying geostatistical analysis. This study represents one of the first applications of geostatistical techniques to the problem of hazardous mining waste site characterization. Remediation of Superfund projects similar to the one described herein represents opportunity as well as liability for the mining industry.

Jan 1, 1992

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Little Rocky Mountains host epithermal- gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining these oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1) mineralization; 2) oxidation; 3) structural setting; 4) lithology; 5) alteration; and ultimately, 6) the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1992

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By Winfield G. Wright, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

The upper Animas River watershed is affected by metal-rich drainage from abandoned mines and by natural weathering of mineralized bedrock. To investigate the importance of natural metal sources, surface waters were sampled in a minimally mined but intensely altered area of the watershed. Water chemistry was strongly controlled by the degree of bedrock alteration. Propylitically altered rocks, which contain calcite, produced neutral waters with low metal concentrations, whereas quartz-sericite-pyrite alteration was characterized by acid-sulfate type waters with high metal concentrations. A mass-balance approach was used to estimate natural metal sources, which accounted for 56-905 of the dissolved metal load discharging from the study area

Jan 1, 2000

By J. E. House

Creative ideas and endeavors require imaginative and positive responses, if they are to be reduced to practices. This lecture will define the plurastic roles of various technical disciplines which were important in the development of the LIX reagents. Specific personalities, facts, and events will be used to trace the development from an idea, to the exciting acceptance and practice of the technology. An objective analysis of the entire LIX reagent development, spanning twenty-five years experience of the author, will be given, these will be used as a basis for critical examination of how the various technical disciplines could improve their effectiveness in advancing future technologies.

Jan 1, 1990

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By A. Exikis

Simulating a ventilation network of an underground mine can help in solving complex ventilation systems with many features, selecting proper fan specifications, location and settings. Early computer systems running simple network simulations were able to provide solutions to the most common and immediate problems regarding underground mine airflow. The more advanced systems available today can perform more sophisticated modeling and simulation of a mine?s ventilation network and present their results in a more understandable and easy to communicate form. This paper presents a ventilation network case study from an underground mine. All aspects of mine ventilation network modeling and simulation are discussed as well as the results from the simulation process. The algorithms and techniques used are thoroughly explained. Some useful guidelines for the application of ventilation network software are also provided in the text.

Jan 1, 2006

By Adolf J. Jonaitis

Outokumpu developed TankCell flotation cell technology beginning in 1990, following 35 years of successful flotation cell experience and application. In 1994, Outokumpu proved favorable operating success of 100-m3 (3,500-ft3) TankCells for porphyry copper and zinc flotation. In 1995, evaluation of a 150-m3 TankCell led to the successful application of these large cells in several operations. More than 350 TankCells of 100 m3 and larger in volume have been installed and are in operation. Key features of the Outokumpu TankCell design will be described. In addition, discussion of operating data from various metallic mineral flotation operations worldwide will be presented. Large flotation cell development continues today, with operating cell volumes of up to 160 m3 (5,500 ft3) in operation.

Jan 1, 1999

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By H. Sis, S. Chander

The beneficial effect of a series nonylphenol polyethylene glycol ether surfactants were tested in the flotation of phosphate ores in which the mixture of sodium oleate and dodecane was used as collector. The performance of nonionic surfactants was first tested in the microflotation of pure apatite mineral. Microflotation experiments showed that the recovery of apatite depends on the number of ethoxylation of the nonylphenol surfactants and decreased with higher ethoxylation. The nonionic surfactant with the smallest ethoxylation group used in this research (NP-4) was then tested in batch flotation of phosphate ores. The flotation of three different size phosphate ores was carried out in the absence and presence of NP-4 surfactant. The beneficial effect of nonionic surfactant was obtained for fine size (-35+150 mesh) and very fine size (-150+400 mesh) phosphate ores at different collector dosages studied. But, in the flotation of coarse size (-16+ 35 mesh) phosphate ore the beneficial effect of nonionic surfactant was obtained only at high collector dosages.

Jan 1, 2002

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By Vicki Seppala

Phelps Dodge Mining Company operates some of the world’s largest open pit mines. Safely mining in these deep pits requires the commitment to a proactive integrated slope management process. The slope management process also includes the continued look for improved slope design, construction, and maintenance of slope faces. This paper discusses integration of such technology as electronic programmable detonators, 3D imaging using ground-based LiDAR scans, and reflectorless slope monitoring systems in a slope management program.

Jan 1, 2005

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By M. G. Ayat

Engineers in the field of coal preparation are continually striving to increase the efficiency of various circuits used in preparation plants. Undoubtedly, one of the important factors concerning the processing efficiency of a coal preparation plant is improved analyses and control of the processing equipment. The necessary link between the performance criteria of a circuit may be provided through on-line determination of various parameters. Currently, there are a certain number of on-line instruments developed for measurement of ash content of coal (Watt and Sowerby, 1983; Kawatra, 1976; Fauth et al., 1984; Lyman and Chester, 1980), moisture content (Hall et al., 1969), and sulfur content (Stewart et al., 1974). In the case of coal separatory units, these parameters are often directly related to the quality of the product. In other words, the extent of misplacement of refuse in the product, or vice versa, would indicate the performance characteristics of any particular coal washing equipment. Partition curves are therefore established to predict the performance of coal cleaning operations. Conventional sampling and testing is currently the major tool with which partition curves are produced and the performance efficiency of the operation is assessed. While conventional analysis techniques are accurate, they are slow and time-consuming.

Jan 1, 1987