Search Documents

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By M. K. Gangal, E. D. Dainty

The paper describes the capabilities of a micro-computer-based real time data acquisition system for monitoring and control of mine environments. Applications of such a system for monitoring the ventilation and air quality of a mine is outlined. The paper discusses the results of running a monitoring system with various environmental sensors in a simulated mine environment. The sensors used in this study are: carbon monoxide (CO), carbon dioxide (C02), nitric oxide (NO), nitrogen dioxide (NO2), sulphur dioxide (SO2 ), methane (CH4 ), air flow, absolute pressure, temperature and relative humidity. A performance evaluation of the monitoring system and sensors is presented.

Jan 1, 1987

By Keith G. Papke

Industrial-mineral mining started early in the history of the State when salt was extensively mined for use in processing gold and silver ores, and borates were produced to meet most of the world's needs. After this start, industrial-mineral production grew slowly until World War II, mostly because of the remoteness of the State and the small population. Nevada now has a large and varied industrial-mineral industry. In 1983, 14 principal commodities were produced from 48 deposits; the total value of these materials was 168 million dollars. Nevada ranks first in domestic production of barite and magnesite; second in diatomite, gem stones, and lithium; third in fluorspar; and sixth in gypsum. Other materials produced are carbonate rocks, cement, clays, decorative and crushed stone, light- weight aggregate, perlite, pyritic soil additive, salt, sand and gravel, and silica. From 1978 through 1982 barite was the most important commodity; in 1983 diatomite surpassed barite in value of production. Most of the Nevada production consists of high-value commodities that are consumed out of the State. Approximately 430 significant deposits with 20 principal commodities are present in Nevada. This abundance can be attributed to the numerous and diverse geologic processes that have been operative. Seven major modes of origin have been identified: hydrothermal activity, sedimentation, combined hydrothermal activity-sedimentation, evaporative precipitation, brine formation, extrusion of igneous rocks, and alteration by ground water. The hydrothermal type accounted for 39 percent of the deposits, the combined hydrothermal-sedimentary type for 28 percent, and the sedimentary type for 13 percent. Nevada diatomite production is about 200,000 short tons/year valued at 30 million dollars. In 1984 three companies operated in Nevada producing diatomite from six open pits and processing it at four plants - one plant producing filter-grade materials and the others adsorbents and fillers. The diatomite occurs in about 60 areas, almost all in the western one-third of the State. The diatomites were deposited in long-lasting, fresh-water lakes in topographically closed valleys formed by basin-and-range faulting. About 85 percent of the barite mined in the United States is produced in Nevada. In 1981 the high point of production,-2.5 million short tons of bedded barite was produced from about 30 open-pit mines. About 120 significant bedded-barite deposits are known in Nevada; 38 of these have had past production of more than 25,000 short tons. The deposits are associated with marine siliceous rocks of Cambrian through Devonian age and occur in a zone about 300 miles long and 60 miles wide. Abundant evidence supports the theory that the bedded barite is of exhalative sedimentary origin.

Jan 1, 1987

By H. E. M. N. Moursy, M. N. Ahmad, C. R. Holland, G. M. Walker, R. D. Chandler

This work describes the effect of process parameters on the acidulation of Moroccan phosphate rock using nitric acid, i.e., the nitro-phosphate process. A series of bench scale experiments were conducted, using a stirred tank reactor (STR) system, to investigate the chemical reactions involved and optimum conditions for the formation of nitro-phosphate fertilizer. The effect of reaction time, temperature, mixing speed, acidulation ratio, and acid concentration were investigated, and were found to have an effect on the dissolution of P2O5 from the phosphate rock, using nitric acid. An increase in nitric acid concentration resulted in an increase in P2O5 dissolution, however, the dissolution was also found to be a function of acidulation ratio. A nitric acid phosphate rock ratio of 4:l ensured 90% dissolution for nitric acid concentration > 30%.

Jan 1, 2002

By Ivor Hawkes

INTRODUCTION High energy breaking is an alternative to using ex¬plosives in underground secondary breaking operations. It also is a means of upgrading conventional hand-held breakers, manual sledge-hammer breaking, and scaling bar operations. Major areas of application are in sec¬ondary breaking over grizzlies and at drawpoints. Other applications include breaking down ripping lips in longwall seam mining, scaling in stopes and rooms, general demolition work, and roadway maintenance. There is considerable interest in high-energy impact breakers for use in primary ore breaking, but, as of 1977, all such applications have been only experimental (duToit, 1973; Joughin, 1976; Wayment and Grantmyre, 1976). EQUIPMENT Essentially, a high-energy impact hammer is a boom¬mounted pneumatically or hydraulically actuated breaker. The machine basically consists of a piston that oscillates in a housing and impacts the end of a tool or moil thrust against the rock. The force applied to the rock primarily depends upon the impact energy of the piston-the higher the impact or blow energy, the greater the force and, thus, the greater the rock break¬age. Among drill and breaker designers, a common expression for blow energy is "force of blow." Hand-held breakers are limited to blow energies of about 140 J (100 ft-lb), because the operator is unable to handle heavier machines efficiently or to absorb the recoil energy resulting from higher blow energies. How¬ever, these restrictions do not apply to boom mounted breakers; machines with blow energies on the order of 4000 J (3000 ft-lb) and higher are available commer¬cially for underground use. There is considerable evi¬dence to show that increasing the blow energy also in¬creases the efficiency of the breaking operation; i.e., more rock is broken per unit of energy expended (Grantmyre and Hawkes, 1975). Thus, there is a trend to higher blow-energy machines, particularly where high¬strength rocks are to be broken. In relation to rock breaking, the blow rate of boom¬mounted impact breakers is not as important as it is for rock drills. This is because the breaker must be moved over the work surface between blows. The blow rate is governed eventually by the power supply, and typical blow rates range between 200 and 600 blows per minute. As a general rule, light blow-energy machines have higher blow rates than heavier machines. Table 1 lists most of the boom-mounted impact breakers that were available commercially during 1977, and it gives details of the blow energies and machine weights. Restrictions are placed on the blow energy by the machine weight and size, and by the strength of the boom. Typically, boom-mounted impact hammers have a blow-energy to mass ratio of about 1.5, with lower values for lighter machines and higher values for heavier machines. In addition to supporting the hammer weight, the boom also has to absorb the recoil energy of the blow, which can be on the order of 1400 J (1000 ft-lb) for large hammers operating in a horizontal mode. Interesting exceptions to the general run of impactors are the Joy HEFTI hydraulic hammers. In these machines, the piston impacts onto a fluid cushion that is positioned between the piston and the impact tool. This approach allows very high piston velocities, over 30 m/s (100 fps), to be used without the risk of break¬ing the piston or impact tool. Steel on steel impacts must be limited to impact velocities of about 10 m/s (35 fps) due to the high impact stresses generated; thus, increased blow energies can be achieved only by increas¬ing the piston size. The Joy 514 HEFTI®, listed in Table 1, has a blow energy of 27 100 J (20,000 ft-lb), but, as of 1977, the machine has been used underground only on an experimental basis. Using a fluid cushion between the piston and the impact tool allows the use of light pistons, reducing the overall machine weight. The recoil energy, which must be absorbed by the boom for a given blow energy, is directly proportional to the piston to machine mass ratio, and operating with light pistons provides an addi¬tional benefit in reducing the requisite boom size. Both pneumatic and hydraulic hammers are avail¬able commercially. Although hydraulic hammers are a relatively recent development, they already outnumber the pneumatic machines in use. There are many reasons

Jan 1, 1982

By F. Duan, W. G. Pariseau, C. S. Schmuck

Three dimensional comparisons between calculated and measured displacements in the hanging wall of a rock mechanics study region at the Homestake Mine show correlation coefficients of 0.7 or higher. Two and three dimensional back analysis of the data lead to different scale factors for determining rock mass strengths and moduli from laboratory values and seemingly to different rock mass properties. A simple analytic model suggests that indeed not only are there two independent scale factors, one for strength and one for moduli, but that there is a logical relationship between the scale factors obtained from two and three dimensional back analyses of the same mine measurements. The three dimensional modeling procedure implemented in the finite element code UTAH3 thus seems to have a realistic potential for investigating underground hardrock mine questions not amenable to two dimensional analysis.

Jan 1, 1987

By F. F. Aplan, S. Chander, A. R. Alaboyun

Several aspects of the capture of hydrophobic dust particles by droplets in sprays have been studied. The particle capture depends on several sub-processes involving collision, adhesion and engulfment. The collision events between dust particles and a single droplet were observed with a high speed motion analysis system to determine the influence of a surfactant on the capture process. In the adhesive process it was observed that the dust particles are collected at the surface of the water droplet to produce a rigid film at high dust loadings. In the presence of the surfactant, however, the particles were engulfed inside the droplet keeping a fresh surface on the droplet available for capture of more particles. A theoretical analysis is presented to take into account the role of contact angle on the penetration of particles into droplets. A significant increase in collection efficiency was observed with decrease in droplet size.

Jan 1, 1991

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By J. C. Yingling, J. Sottile

This paper addresses detailed models of the temporal pattern of material flows produced by longwall mining units and procedures for inferring the parameters of these models from field data. First, a model is established that predicts material flows referred to shearer position and cutting element. This model is comprised of trend and fluctuation components. The trend component, which is invariant between repetitions of the cut cycle, accounts for deterministic effects on the flow pattern, such as web depth variation as a function of the cutting operation, systematic tendencies for seam height and cutting speed variations along the face, changes in the relative velocity between the shearer and face conveyor, etc. The fluctuation component models random effects on material flow and employs time series approaches. Subsequently, a method is given for converting the positionally-referenced flows to temporally-referenced flows. The model serves as a basis for generating detailed, accurate computer simulations of material flows from longwall units. As such, it provides a more rigorous foundation for analysis of cutting procedures and outby materials handling systems in longwall mines.

Jan 1, 1994

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By Steven A. Elmquist

Although past investigations (2, 5)have been conducted to determine crushing relationships, no program which covered a broad range of crushing conditions had been conducted. The previous studies appear to concentrate on small segments of the overall picture and did not fullfill our desired information objectives. The Crusher Variables Research Program conducted at the Mineral Research and Test Center (MRTC) of Rexnord, due to the broad range of variables utilized in a production size crusher, is believed to be the most comprehensive study of its kind as of this date. The principles developed by the Symons brothers in 1925, when they patented the cone crusher as we know it today, are still being used in the machine known as the Symons Cone Crusher, During the development of this novel crushing concept, a technique known as the fall of material (called the Bouncing Ball Theory1 by some) was used to determine an idea as to the proper head angle, eccentric and speed of eccentric rotation, The final variables used for the Symons Cone Crusher design were, therefore, the logical conditions to start with and use as a reference against which other variables could be compared.

Jan 1, 1979

By Fred Leighton

INTRODUCTION Dynamic (seismic or microseismic) methods of determining the stability of structures in rock are based on detecting and analyzing the characteristics of seismic energy that has originated from or traveled through the rock mass. This seismic energy can be in the form of naturally occurring rock noise energy resulting from structural adjustments within the rock or can be introduced into the structure by physical means, such as by blasting or impact. In either case, the seismic energy radiating through the rock mass can be detected using standard equipment and can be analyzed by established techniques to reveal a wide variety of information concerning the condition and stability of the rock mass through which the energy has traveled. In the following sections, the basic instrumentation required for seismic and microseismic studies is described, and some of the presently used applications of these methods are discussed to exemplify the state of the art. INSTRUMENTATION Seismic disturbances in a rock structure generate two types of seismic wave radiation, body waves and sometimes surface waves, which radiate outward in all direc¬tions from the source of the disturbance. Underground mining applications are generally concerned only with discerning the characteristics of the resulting body waves, i.e., the compressional (p-wave) and the shear (s-wave) energy. As these two forms of energy travel through the rock structure, the particles of the rock mass are caused to vibrate, and the vibration character¬istics resulting from each of the two types of wave are distinct. Some important differences are: 1) Compressional and shear waves travel at different velocities through the rock structure. 2) The frequency at which each wave causes particles to vibrate is different, and may range from about 50 to 100 000 Hz. 3) The amplitude or energy level of each wave is different, with the shear energy usually being the greatest. These differences form the basis for equipment se¬lection for individual studies and for modern data analysis techniques. The following sections describe the basic equipment necessary to detect and record seismic wave energy data and show several examples of analysis procedures and how these procedures have been used. In principle, seismic equipment is very simple. It consists of a geophone (or geophones) to detect the seismic energy vibration and convert that vibration to an electric signal, an amplification system to increase the level of that signal, and a means of monitoring and/or recording the signals detected. Fig. 1 is a block diagram of a typical system. The following sections offer a very brief discussion of system components and their individual functions. A more complete discussion is given by Blake, Leighton, and Duvall (1974). Geophones The function of the geophone is to detect the vibrations caused by the passing of the seismic wave energy and to convert that vibration into an electrical signal that displays both the amplitude and frequency characteristics of the vibration. Particle motion or vibration can be quantified and measured by measuring displacement, velocity, or acceleration of the particles. Thus, there are three types of geophones: displacement gages, velocity gages, and accelerometers. The choice of gage depends on the characteristic frequencies of the seismic energy to be monitored and the sensitivities of each type of geophone. In general, displacement gages are used for low-frequency monitoring (periods to 1.0 Hz), velocity gages for medium-frequency monitoring (1.0 to 250 Hz), and accelerometers for high-frequency monitoring (250 to 10 000+ Hz). Experience has shown that in underground studies, the choice of which gage to use lies between velocity gages and accelerometers. An easy, accurate method for selection of gage type is discussed by Blake, Leighton, and Duvall (1974). Once the type of geophone has been selected for use, it must be properly installed, and in the installation procedure the most important step is insuring that the gage is firmly attached to a competent portion of the rock structure. Poorly mounted geophones may entirely fail to recognize low-level seismic signals and will distort the information from signals they do see. Amplifiers Seismic events associated with mine structures occur over a very broad range of energy which results in a broad range of geophone output levels. In general, geophone output levels occur in the microvolt to low milli-volt range, and it is necessary to amplify these signals in order to drive recording or monitoring equipment. Because either an accelerometer or a velocity gage might be used as the geophone, the amplification system must

Jan 1, 1982

By A. Juganda, Jr. Bogin, J. Brune, J. Grubb, S. Lolon

"Face ignitions at the longwall face are a serious hazard in underground coal operation that can lead to a major mine explosion. Despite having methane monitoring system mounted on the shearer and at various locations on the longwall face, undetected accumulations of methane can still occur and result in face ignitions. With the use of Computational Fluid Dynamics (CFD), the interaction between the air flow at the longwall face and factors that contribute to the accumulation of methane around the longwall face can be modeled and visualized in great detail. The results confirm that the tailgate corner of longwall face is a critical area that is prone to face ignitions and needs to be properly monitored. The occurrence of roof falls on the tailgate entry inby the face and/or poor caving conditions behind the shields can pose a safety risk in the longwall operation. Poor gob caving can lead to insufficient face air quantity to dilute methane at the tailgate corner, while blocking of tailgate by a roof fall can carry methane contaminated air from behind the shields back into the face near the tailgate corner and pull the explosive gas zones (EGZs) inside the gob closer to the face. INTRODUCTION Ignitions of accumulated methane gas at longwall faces are well known to be among the major causes of methane explosion in underground coal longwall mining operations. Some of these ignitions can lead to major mine explosions, such as the Upper Big Branch mine disaster in 2010, in which methane migrated from the gob to the shearer cutting drum where it was ignited, resulting in a major mine disaster (Phillips, 2012). History has shown that, despite having methane monitoring systems mounted on the shearer and various locations at the longwall face and alarms set to 1% CH4 (Mine Safety & Health Administration, 2012), undetected accumulations of explosive methane-air-mixtures can still occur and result in face ignitions. Recent study by Verma and Brune (2016) state that frictional ignitions on longwall faces contributed to 379 incidents or 23% of the total 1,637 cases of face ignitions recorded from 1983 to 2014. The common cause of mine explosions usually involves poorly designed ventilation systems, insufficient ventilation, and inadequate monitoring in critical areas that are prone to methane accumulations. In longwall operation, the tailgate corner of the longwall face can be considered as one such critical area. On-site studies by Krog et al (2006) and Thakur (2008) show that increasing the longwall panel width may also increase cumulative methane emissions at the tailgate. There are also indications that increasing longwall face lengths can result in an increase of the void space behind the face under certain roof conditions (Schatzel et al, 2006). This may cause higher leakage rates from the face to the gob, thus reducing the amount of fresh air available at the tailgate."

Jan 1, 2017

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By D. J. Kennedy, A. W. Stokes, W. G. Klinowski

Sulphur hexafluoride (SF6) has become an accepted standard in the field of mine ventilation tracer gas studies. It has a wide variety of uses for defining mine ventilation flows that cannot be adequately described using conventional instruments such as anemometers and smoke tubes. The Cape Breton Coal Research Laboratory (CBCRL), Energy, Mines and Resources Canada, has been using SF for the past 4 years and has developed numerous release and sampling systems to increase its versatility. The CBCRL has also completed a successful field trial of an automated rapid sequential SF6 analyzer (which gives a pseudo real-time readout) that can be used underground. In doing this work, the authors recognised the potential of being able to use more than one tracer gas simultaneously in an underground study. Two alternative tracer gases (Freon-13B1 and Freon-12) have already been used by CBCRL in some of their underground work. These gases can be measured by gas chromatography utilising an electron capture detector in a similar manner to SF6. A description of these gases, the methods for 6' their handling, release and sampling are given in this paper together with a brief outline of the analytical system used to measure them. Their suitability to mining applications is compared with SF6. A study in which these three gases were used together is discussed and the results and conclusions given. Some of the additional uses for multiple tracer gases to assist the mine ventilation engineer in resolving problems and improving his day-to-day monitoring are discussed. Finally, a brief analysis of developments which can be expected in the near future is outlined.

Jan 1, 1987

By Gunter Zimmermeyer, Hartmut Eicker

Radon in the Environment Radon, as a natural nobel gas, can be detected nearly everywhere in the environment as a decay product of ubiquitous uranium. As it is emanated from soil and rocks measurable concentrations have been found at the surface of soils and in even higher concentrations in enclosed spaces like, for example, mines and buildings. While above soil surface activities caused by radon have been found in an order of magnitude of up to 1 pCi/l (Weigel, F. 1978), concentrations in enclosed spaces and mines are higher because of the lack of atmospheric circulation. Beside air circulation the relevant figure depends on the Ra226-concentration in the surrounding rocks or building material, as well as on emanation coefficient and the diffusion coefficient. While representative Rn222concentrations in well ventilated buildings are reported to be in an order of magnitude of 1 pCi/l maximum values up to one order of magnitude higher have been found in badly ventilated brick buildings (Ettenhuber, E., Lehmann, R., Clajus, P., 1978) (Aitken, J.H., et al., 1977). Just now it was stated that the reduced air circulation due to German legal regulations on energy conservation will increase radon exposure of the public considerably (Jacobi, W., 1979). Radon in Mines Radon exposure of workers is, of course, a matter of concern in uranium ore mines where relatively high concentrations of the uranium to be mined are present. Measures to protect workers' health have been implemented, based on experience on dose-effect relationship. They serve to meet exposure standards by limiting inhalation of radioactive particles, in reducing radon concentrations or in limiting working hours. Both improved measuring devices and capacity as well as the lower discrimination threshold enable to measure radon concentrations in other mines, e.g. in coal mines. It is known that radioactivity in coal is small compared with that in other minerals and even soil, rocks. Nevertheless, radioactive elements were identified in coal and so the question was whether the concentrations of radon in coal mines might be a subject of concern. The problems encountered when measuring radon in coal mines are described below, as the measuring device has to be flame proofed which is an important additional requirement. Measured radon concentrations in British coal mines have already been published (Duggan, M.J., Howell, D.M., Soilleux, P.J., 1968 (Dungey, C.J., Hore, J., Walter, M.D., 1978). The authors found concentrations of up to 14 pCi/l in Cornish mines. In most cases the values were in the order of 2 pCi/l. These results were consistent with measurements reported from U.S.-coal mines (Lucas, H.F., Gabrush, A.F., 1966). Such concentrations of radon were not considered to represent a hazard for British miners (Ogden, T.L., 1974). In Germany, too, first measurements have been carried out in five coal mines in the Saarland in the 60's. Air samples were taken at different places in the coal mines, dried, fed to an ionisation cell and measured by a device including reference cells. Samples taken at ventilated places showed radon concentrations consistent with the lower British results. They all kept within the standards of the first German regulation on protection against radiation. Measuring the radon daughters was renounced because of the relatively low radon concentrations and the requirements for flame proofness in coal mines. Moreover, it can be ascertained that because of the effective ventilation the disequilibrium factor between the decay products and the radon concentration remains far below the value of one (Muth, H., 1978) (Keller, G.). In 1979 the committee on mine safety and health protection in coal and other mines of the EEC proposed to have measured and evaluated radon concentrations in European coal mines to find out whether they complied with international standards. Great Britain and Germany agreed to this proposal and by commissioning such measurements to scientific institutes complied with the request to harmonize the methods used. In the Federal Republic of Germany, e.g. Westfälische Berggewerkschaftskasse (WBK) and Staatliches Materialprüfungsamt; Dortmund (MPA) were requested to carry out the measurements in coal mines of the Ruhr coalfield whereas Saarberg Interplan was responsible for the Saar coalfield. The WBK measurements are reported in later paragraphs.

Jan 1, 1981

By Raul Z. L. Cançado, Virginia S. T. Ciminelli, Roberto Galery, Armando C. de Araujo

Brazil is presently among the seven largest gold producing countries in the world. This paper discusses the evolution of gold mining through the history of Brazil. It also gives a general account of the present practices for mining, processing and extraction of gold. Flowsheets of some selected plants are presented. The environmental aspects involved with gold production are also considered.

Jan 1, 1987

By L. A. Henry

The island of Jamaica consists predominantly of Carbonate rocks which vary in chemical & physical characteristics. Currently these rocks are used for construction and road aggregate, landfill and as a raw material in the manufacture of cement. Over the past fifteen years the Geological Survey of Jamaica with assistance from a number of international aid agencies and the private sector have identified deposits of high calcium/high brightness limestones which have the potential to be utilized as a high quality filler and a number of other commercial applications. Geologically, these limestones are formed within the Eocene Swanswick Formation, the Oligocene Walderston-Browns Town Formation and to a lesser extent the Miocene Montpelier and Newport Formations.

Jan 1, 1998

By W. S. Fyfe, R. J. Puddephatt, S. Zhou

Gold is easily mobilized at temperatures within range 600-11OO°C by gases such as Cl2, CO, H2S, in gas mixtures, at low pressures. Such gases are relevant to conditions of granulite facies metaomorphism in environments of magma underplating. These observations suggest an efficient mechanism for moving gold to the upper crust during major thermal events. The efficiency of precipitation of gold at lower temperatures is related to available mineral surfaces and pyrite appears to be an excellent substrate for gold precipitation.

Jan 1, 1989