Search Documents

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By L. G. Kirk

The Mississippi embayment ball clay region, including western Kentucky, western Tennessee, and northwestern Mississippi, accounted for more than 95% of the total U.S. ball clay production during 1985. Other producing states during the year were Texas and Maryland. The U.S. Bureau of Mines reported total domestic production for 1985 of 910,000 short tons. The United States exports approximately 20% of the annual ball clay production. Geologically, the ball clay deposits are sedimentary in origin and occupy the north- eastern flank of the Mississippi embayment. The commercial deposits have been confined to the Claiborne and Wilcox formations within mid to lower Eocene and upper Paleocene age strata. The deposits are lenticular in nature and highly variable in areal extent and thickness. They exhibit very abrupt lateral boundaries and are bounded laterally and vertically by unconsolidated sands, silts, and waste clays.

Jan 1, 1986

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By G. Whitney, J. Steiner

Introduction The Summitville Mine located in southwestern Colorado is an example of the potential impact that natural weathering and mining activities can have on environmental quality. Acid rock drainage and metals leaching from active and historic mine districts are a major environmental problem facing the mining industry today. Sulfide ore exposed naturally or during mining operations has the potential to produce leachates that contain high concentrations of dissolved metals. These leachates can affect the quality of plant and animal health in surface water used for agriculture, recreation and human consumption. Pintail Systems has developed biological processes for detoxification of cyanide in heap-leached spent ore and process solutions. During application of spent ore cyanide bio-detox processes we have also observed a substantial reduction in many of the leachable metals in biotreatment solutions. These field observations of soluble metal reduction led us to propose that metal bio-mineralization should be a secondary treatment goal of spent ore detox in Focused Feasibility Studies (FFS) for the Summitville Mine. In the FFS (described in a companion paper) for Summitville, spent ore from the heap leach pile (HLP) was loaded into PVC test columns (six inch X ten foot) and was leached with bacteria/nutrient solutions. Two treatment designs were studied: a standard percolation leach (aerobic) and a saturated leach design where the ore was saturated with the heap leach solution to which bacteria and nutrients were applied in a continuous biotreat leach. The bacteria for all column treatment tests were isolated from the spent ore at depth through the Heap Leach Pile (HLP) in the saturated and unsaturated zones. Bacteria isolated from the heap material were tested for cyanide oxidation capacity and were submitted to a bioaugmentation program to improve reaction kinetics and metals tolerance. The final treatment population consisted of several distinct species including aerobic heterotrophs, facultative anaerobes and sulfate-reducing bacteria. The remineralization of soluble metals was observed through a decrease in copper in column leachate solutions and the formation of observable mineral products on ore surfaces in the columns. Several of the tests were run in clear PVC columns to facilitate observation of mineral formation. The column ore contents were photographed before, during and after the biotreatment process which ranged from 10 to 20 days for each test column. Ores were collected from each column after the treatment was complete and were submitted for SEM and TEM study at two laboratories - the USGS SEM Laboratory in Denver, Colorado and the City College of New York SEM laboratory. Treatment Process Description Numerous species of bacteria, fungi and yeasts are capable of accumulating many times their weight in soluble metals. Both living and dead biomass are effective in removing soluble metals from waste streams containing gold, silver, chromium, cadmium, copper, lead, zinc, cobalt and others. Soluble metals may also be immobilized in soils by natural or engineered biomineralization reactions. Several commercial processes using biological reactions are being applied on an industrial scale for metal remediation. Bacteria found in natural and extreme environments have developed a wide variety of metabolic functions to adapt to these environments. These natural microbial functions contribute to global mineral cycling that continuously forms, transforms and degrades minerals and metals in the environment. Biomineralization is described as a surface process associated with microorganism cell walls where the remineralization occurs. The biogeochemical activities initiated by microorganisms in ores, soils, surface and groundwater environments can dominate the formation and transformation of those mineral environments.

Jan 1, 1995

By C. E. McFarland, N. W. Kirshenbaum

Cortez Gold Mines is located about 75 miles southwest of Elko, NV. Activity in the mining district dates from 1862. The current operation developed from a 1963 joint venture of Webb Resources, The Bunker Hill Company, Vernon F. Taylor, Jr., and American Exploration & Mining Co. Three years later, the USGS discovered gold on the property following a regional geochemical survey. Drilling in 1966 and 1967 identified 3.4 million st of oxide ore grading 0.28 oz Au/st, and a 1700 st/day countercurrent decantation mill was commissioned in 1969. Heap leaching started in 1971 on low grade ore and continues to the present. The mill was shut down in 1976 following exhaustion of known oxide reserves. Mobile equipment was sold and the proceeds committed to local exploration. In 1980, a new plan of operations was developed starting with existing low grade and newly discovered mill ore. The mill resumed operations in 1981 and has been operating to date. A series of metallurgical innovations, culminating in the commissioning of a new fluid bed roaster in the summer of 1990, has enabled treatment of a series of increasingly refractory ores. Current partners in the venture are Kennecott Corporation, Vernon F. Taylor, Jr., and Placer Dome U.S. Inc., manager of the operation. Idaho Mining Corp. holds a 7.5% carried interest.

Jan 1, 1992

By Leonard Harris

Most of those involved in the mining industry are aware of the negative feelings that the well-informed citizens of this country, also known as the American public, have for the industry. As noted in an issue of Mining World News, “The general public perceives mining as dirty, noisy, destructive and belonging somewhere else.” The same theme was raised at a conference in Scotland in July 1991. It was noted there that mining has an unattractive public image around the world “as dirty, dangerous work that pollutes and degrades the environment.” Why is this? Why does mining have such a bad rap? I’m afraid that some of the blame rests with the mining industry itself - both in the past and in the present. Hopefully, we can do something about this in the future. And hopefully, the information here will help the reader to spread the word to offset the negative messages being issued almost daily by industry foes. I hope this will become more than just the words of another miner talking to miners and their friends. In the past, belching smokestacks and polluted streams and waterways were common sights. Today, the negative results of mining operations can also be seen in the form of waste dumps, leaked acid mine waste water and dust blowing from tailings piles. Some will argue that mining did nothing illegal in the past, and that all the regulations in force at that time were carried out to the letter. That may be so. The fact remains, however, that mining did these things, and the evidence is very clear in many parts of the country. It is visible to the well-informed citizens, in spite of the fact that many mine sites have been cleaned up and new technologies, such as flash smelting, dump leaching, pressure leaching and bioleaching, have greatly overcome many of the pollution problems. What is not so visible is the importance of the mining industry in our daily lives. Not long ago, knowledge about our non-renewable mineral resources ranked low on the list of qualifications for being a well-informed citizen. Events during the past two decades have changed this scenario. Politicians, writers, newscasters, economists and administrators, as well as the ‘public,’ are expressing opinions and forming judgments on oil company profits, desecration of landscapes, waste disposal sites and pollution by the extractive industries.

Jan 1, 1992

By D. M. Stephens

Feeder-Breakers were an unknown but much needed piece of machinery when U. S. underground coal mines started converting to more efficient belt haulage of the R.O.M. coal as compared to conventional methods that the 1950's offered. These simple electromechanical machines offered efficiencies in three areas: (1) they contained a surge hopper that allowed a "load' of coal to be dumped without delay; (2) this material was fed horizontally by a drag chain conveyor into a rotating carbide pick breaker that broke all oversize material into a beltable size, and (3) it fed this broken material onto the belt conveyor at a rate conducive to its design. Since its introduction, the Feeder-Breaker has evolved from that first low capacity, low breaking force machine to today's model capable of breaking materials up to 5 MOHS in hardness and having throughput capabilities exceeding 3,000 TPH with availability in the 90 percentiles.

Jan 1, 1985

By Ralph W. Barbaro

In many parts of the country, electric utilities use spot market coal to make up the difference between the amount of contract coal and the total amount burned. The utilities involved will normally have a structured contract for those companies supplying that spot coal. These contracts will often involve a pricing schedule with bonuses or penalties for coal above or below the specified coal quality goals. Normally, penalties will be assessed on the sulfur, ash, and other coal quality variables. This paper deals with some aspects of the pricing schedule of one of the eastern utilities that buys coal on the spot market. This utility has a number of plants that a supplier can attempt to supply through bidding procedures. The existence of the pricing schedule gives the supplier a number of different options. To the single-mine producer, options are available to send the coal to any demand site and to clean all, part, or none of the coal. In other words, he can ship to a number of different sites and can send different coal qualities to each site depending upon the level of preparation. In addition, the options to deliver blended coal to any given site will provide an additional level of complexity to the problem.

Jan 1, 1983

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By M. Shriwas, F. Calizaya

"Controlled recirculation may be considered as a beneficial means in mines of cold climate, where heating of air is required, and in deep or extensive mines, where cooling of air is required. Controlled recirculation can be designed by proper sizing of the booster fans with respect to main fan. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario shows lesser buildup of methane concentration than the former one. INTRODUCTION The controlled recirculation is designed purposefully to allow a partial fraction of used air that increases the air velocity due to increased quantity of air and consequently allows effective dilution of contaminants to improve local ventilation condition at the working face. It can be designed by proper sizing of booster fan with respect to main fan in a ventilation network. Controlled recirculation may be categorized as crosscut, in-line or combined system based upon the configuration of the booster fan locations in a district ventilation network. Research on controlled recirculation has shown numerous benefits of controlled recirculation especially in deep or extensive underground mines, where further heating or cooling is required (Calizaya 1990; McPherson 1993 and Jones, 1987). However, fear of buildup of concentration has misled the mining communities to view the controlled recirculation as a hazard and deprived the mining industry to derive benefits from recirculation. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario result shows the less buildup of methane concentration than former scenario result."

Jan 1, 2016

By P. Aparicio

The rheological properties of five kaolins, isostatically pressurized at 4 x10 Pa for 10 min in the presence/absence of water, was determined. Under dry conditions, measured viscosity values either decreased or remained the same. After treatment under wet conditions, measured viscosity values were 30-60% higher at high shear and 50-60% higher at low shear. These results correlate with variations in nanomorphology and structural order. Dry compaction degraded kaolinite crystals but wet-pressing appeared to cause an increase in the proportion of euhedral crystallites and a decrease in deformed crystals. Dry compaction decreased the low-defect phase proportion (ldp), but in contrast, the ldp in wet-treated kaolins remained constant or increased. Results show that hydrous pressure treatment produces a change in viscosity of kaolin suspensions, yielding the potential for improving paper coating performance, whereas anhydrous pressure treatment decreased or maintained the viscosity.

Jan 1, 2010

By K. Koizumf, A. A. Cram, K. Whitchurch

The Expert Scheduling is a new, exciting method for scheduling underground and open-cut coal mines. A key feature of the Expert Scheduler is the adoption of an expert or artificial intelligence system. The expert system makes decisions regarding the schedule, such as which area should be mined. With existing scheduling systems these choices are made by the scheduling engineer. Developing one area may be better than another if it offers better quality or lower costs. Information the engineer considers in these decisions could be; • coal tonnage and quality targets, • equipment utilisation, • mining cost, • and other practical constraints. In expert scheduling a number of experts are appointed to make these decisions. A number of mining strategies are examined for each period. Information for each strategy is evaluated by "experts" and the "best" solution adopted. The method is based on the Blackboard Techniques. With this technique information is presented to "knowledge sources” or "experts" by the Blackboard Controller for their "opinions". These "opinions" are examined by the Blackboard Controller to select the best strategy. Engineers can readily add experts to the system, and modify the weighting of experts to suit mining conditions. Using an Expert Scheduler means that many schedule op- tions can be analysed quickly with full repeatability.

Jan 1, 1996

It is well established that the results of emulsion flotation in which water-insoluble oily collectors are utilized depend critically on the emulsification of the collector and on its conditioning with the pulp prior to flotation. The flotation tests carried out with magnesite and fluorite using sodium oleate as collector confirmed acidic and alkaline ranges of good flotation. While the flotation results in the acidic solutions depend strongly on the conditioning time and can be very much improved when longer conditioning times are utilized, the tests in the alkaline environment do not exhibit any significant dependence on conditioning. The results obtained with sodium salts of myristic and lauric acids confirm these findings. The observed effects provide additional evidence for the role of the colloidal species which appear in the acidic solutions of weak electrolyte type surfactants, such as fatty acids. The flotation properties of sodium oleate in the pH region in which it appears in the form of oleic acid droplets are mainly determined by the properties of such droplets. The flotation in this pH region closely resembles an emulsion flotation.

Jan 1, 1993

By E. Watkins, S. J. Schatzel, K. Ajayi, V. Gangrade

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research related to unconventional gas wells positioned in abutment pillars associated with active longwall mining in Southwestern PA. The Ventilation and Explosion Prevention Team at NIOSH is working toward predicting and characterizing a hypothetical casing breach and its effect on the safety and health of mine workers, gas well workers, and the general public. An important aspect of this research is to distinguish coalbed gas from shale gas in the mine environment as an indicator of a casing breach. Another noncoal gas source exists in the region in the form of underground gas storage fields which also have the potential to migrate towards mine workings. During a potential gas breach, the addition of excess natural gas to coal mine environments will exceed the anticipated ventilation loading and can create a mine explosion hazard. A methodology has been developed to distinguish these gas sources. Gas samples from the three sources were analyzed by gas chromatography, and interpretive methods were applied to distinguish the populations graphically and statistically. Bivariate plots using the hydrocarbon index and the normalized molecular ratios showed that the sources occupy different regions of the graphs. All samples of non-coal gas contained under 2% CO2, and all coal samples included greater than this amount. A multivariate T-squared (T2) test analysis relating comparing data in pairs showed a low p-value (dimensionality parameter) and a high T2 test statistic for all comparisons, indicating that these sources are different and distinct gas populations. Ultimately, stakeholders from the mining and gas production industries can utilize this method to identify gas sources and a potential casing breach.

Mar 2, 2022

By Lynn B. Hales, Randy A. Ynchausti

Introduction There continues to be a large economic opportunity associated with improving process performance through advanced process control systems within the minerals industry. The basis for this opportunity lies in the inherently low efficiencies of many of the unit operations found in mineral processing plants as well as the continual variation that is present in the ores being processed. The ageless target of such control systems is improved recoveries and concentrate grades, higher processing rates and lower unit costs. Many plants are enjoying the benefits of modem, well functioning process control systems but few if any have achieved plant-wide optimization in an economical sense. As new process modeling and control technologies, such as neural networks, continue to evolve and develop, the potential for plant- wide optimization is becoming a closer reality. Neural network technology appears to have a significant potential in the general field of process control and control of mineral processing operations. Neural networks are an emerging technology that have been evolving out of the study of biological systems since the early 1940's. The first software simulation of neural computing networks was reported in 1956 by Nathanial Rochester of IBM Research during the first conference on artificial intelligence which was sponsored by the Rockefeller Foundation. Neural Networks Neural networks can be considered to be a class of computer program that perform their problem solving functions based on a rudimentary model of the human brain and how it solves problems. Traditional computer programs and even computers themselves solve problems or process data sequentially and in a deterministic manner. The human brain, on the other hand, processes data and solves problems in a massively parallel fashion. We think of computers normally in terms of having a single processing unit, sometimes a co-processor to assist in certain activities such as mathematical functions or communications, bytes of memory, processing speed and program/data storage size.

Jan 1, 1992

By M. M. Champion

INTRODUCTION Since the first introduction of explosives into mining operations, safety considerations have prohibited the use of machinery in association with the explosives. Only within the last 25 years has this situation changed appre¬ciably; the closest thing to "machinery" used by a powderman in the "old days" was his wooden tamping stick. With the blackpowder and dynamite used during the first 150 or so years of mining blasts, substituting a drill steel or a metal "spoon" invited serious disaster. With the advent of ammonium nitrate-fuel oil (ANFO) explosives (1950s) and water-gel explosives (1970s) for underground blasting, machinery started to play a large part in blasting procedures. The lower sensitivity of ANFO and water gels allows these prod¬ucts to be loaded in a variety of safe ways. Not only has this meant cost savings in labor and blasting materials, but it has also resulted in whole new mining concepts where the limitations of dynamite previously made those concepts uneconomical, impossible, or excessively risky. Increasingly (totally for some mines), the traditional tamping stick has given way to a variety of pneumatic machines for loading explosives and blasting agents. The resulting blasting operations have become safer, more efficient, less uncomfortable for personnel, and a major step forward in mining technology. ANFO LOADING EQUIPMENT Three basic types of loaders are used for ANFO explosives, these being the pressure-vessel loaders, Venturi loaders, and combination loaders. Pressure-Vessel ANFO Loaders ANFO consists of prilled ammonium nitrate (porous pellets I to 2 mm in diam) and fuel oil in the appro¬priate 94 to 6% blend. The material is fairly dry, pourable, and easily conveyed by an air stream. One device or system for handling (hole loading) ANFO is the pressure-vessel loader. ANFO is dumped into the vessel or "pot," and the vessel then is pres¬surized. The ANFO is conveyed out of the bottom of the vessel into a semiconductive hose that has been inserted into the blasthole. Fig. 1 illustrates a typical pressure-vessel loader in use. Applications: The use of pressure-vessel loaders is widespread in room-and-pillar mines, including salt, potash, trona, lead, and other rubber-tired mines where the heavy pressure vessels can be mounted on a vehicle for transport from face to face. The vessel often is large enough to hold eight or more 23-kg (50-1b) bags of ANFO, so several faces can be loaded before refilling. Pressure-vessel loaders also are suitable for effec¬tively loading long holes such as those that are 6 m (20

Jan 1, 1982

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new, as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1) (2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation’s Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout- rebar system.

Jan 1, 1977

By L. G. Stolarczyk

In-mine Continuous Wave (CH) Radio Imaging method (RIM) instrumentation has the capability of measuring EM wave propagation constants in layered formations. The RIM method is based upon the fact that seams of coal, trona, potash, quartzite, gilsonite and oil bearing sands form natural waveguides for low loss transmission of electromagnetic (EM) waves. The waveguide forms whenever the seam is bounded by more conducting claystone, mudstone, shale or in the case of oil/gas traps, by a floor of saline water. Disturbances caused by faults, shear zones, paleochannels, sills and dikes significantly alter the propagation constant. The analytical values of the EM wave propagation constants depend on the physical and electrical parameters of the seam. The values are presented in this paper in a graphical form to assist in the interpretation of RIM tomographic images. This paper compares in-mine geologic mapping obtained during mining to tomographic images of the geologic disturbance zones in a Central Utah coal mine.

Jan 1, 1989