Search Documents

By J. R. de Wet

The behaviour of mild steel in aqueous cyanide solutions similar to caustic cyanide elution solutions was investigated at high temperature in electrochemical experiments. The anodic polarization diagrams of mild steel indicated that steel may undergo active dissolution under these conditions. The rare occurrence of gold plating in practice is the result of the limiting of the anodic dissolution of the steel by the presence of a passive layer on the steel. This passive layer is stable only in a certain potential range, and the free corrosion potential attained determines whether the steel will be passive or active. For conditions typical of elution columns, several corrosion potentials are possible, depending primarily on the initial condition of the steel and the concentration of oxygen in the solution. If these conditions result in the formation of a passive layer on the steel, changes in concentration and temperature will not necessarily result in plating since the layer may exist in a metastable form.

Jan 1, 1993

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By R. J. Dippenaar, J. C. van den Berg

This paper describes an investigation into the prereduction of hematite fines in a fluidized-bed reactor as a means by which they can be prepared for direct smelting in a transfered-arc plasma furnace. A single-stage fixed fluidized bed reactor using the in situ gasification of coal was employed. It is shown that the hematite is reduced to magnetite at 1000 QC, the degree of reduction being limited by the inherent shortcomings of a single-stage reactor in which both the gasification and the reduction reactions have to occur. Methods by which the degree of reduction can be increased are suggested. The gasification process was studied in some detail, and three different reducing agents are compared. The dominating effect of the Boudouard reaction on the behaviour of the fluidized bed is clearly illustrated. Non-coking coals of high reactivity are best suited to this process, a finding that would complement the trend away from coke as a metallurgical reducing agent.

Jan 1, 1989

By J. H. Viljoen, N. B. Strydom, J. S. Greyson, C. H. Van Graan

SYNOPSIS Bad eyesight and poor illumination can contribute to the occurrence of accidents in mines. As one part of a study of this problem, surveys of light intensities have been conducted in 19 gold mines. On 17 of the mines the surveys were on one underground level only, whilst in two of the mines more intensive surveys were conducted by measuring light intensities in all areas to determine any inter-mine variations between the levels of illumination. Readings of light intensity were taken underground at stations, tips, winches, stopes, conveyor belts, waiting places, pump stations, fitters' and boilermakers' workshops, ambulance rooms and in haulages. It is concluded that the average levels of illumination in South African gold mines are comparable with those reported in the literature for mines elsewhere. Standardisation of lighting conditions underground could eliminate inter- and intra-mine variation in illumination levels where they occur. A guide to mine illumination practice would assist such standardisation, and help increase the levels and effectiveness of illumination in mines. Some suggestions are made in this latter connection.

By D. D. Howat, J. van der Colf

This paper is the first in a series of three dealing with this subject and also with the rate of oxygen removal from the slags in the presence of solid carbon and with the physicochemical properties of the reduced slags. For selected members of the system, the melting temperatures and primary crystallization products were determined. as were the viscosity and the electrical resistivity of the corresponding melts. All the experiments were conducted in a neutral atmosphere. Where determined, the primary phase was found to be either perovskite or magnesium aluminium titanate. The composition variable exerting the most pronounced influence on viscosity or resistivity was found to be the basicity expressed as the mass ratio (CaO + MgO)jSiO,. The ratio CaOjMgO became important only at Iow basi<:ity values. Although generally there is a direct proportionality between log (viscosity) and log (resistivity), slags h&apos;lving either a very high silica content or a very high titania content have anomalously Iow electrical resistance.

Jan 1, 1979

By P. J. D. Lloyd, Jill Urban, M. R. Urban

The adsorption of gold from cyanide solutions onto constituents of the reef, and its role in reducing the efficiency of the gold-recovery process by M. R. URBAN. M.Sc. (Chem. Eng.) Rand (Visitor). JILL URBAN. B.Sc. (Chem. Eng.) Rand (Visitor) and P. J. D. LLOYD. Ph.D. (Cape Town) (Fellow) Evidence for the adsorption or re-precipitation of gold from cyanide solutions onto gangue minerals of the Witwatersrand reefs has been gathered over a number of years by various investigators. The evidence from tests using radioactive tracers is conclusive and indicates thlt adsorption contributes about 0,1 g/t to the total gold loss from conventional reduction works. The loss is a function of the alkalinity and cyanide concentration of the solution, and it appears to be affected by the extent of time between milling and cyanidation. The heavy minerals appear to be the strongest adsorbers, and the clay minerals somewhat less strong adsorbers. A sensitive qualitative test based on thin-layer chromatography permits the extent of adsorption and desorption to be readily determined.

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 251 to 257. These financial statements are the responsibility of the institute&apos;s Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropri¬ateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the institute at 30th June, 1998, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1998

By M. C. Mulligan

Counter current decantation (CCD) thickener circuits are used to recover soluble metal as pregnant liquor solution from ore leach residue. The basis of CCD operation is to concentrate suspended solids thereby minimizing liquor content in underflow slurry that flow in one direction. Then the underflow slurry liquor is diluted with wash liquor that flows in the opposite direction and the suspended solids are concentrated again and again. The amount of liquor in the thickener underflow contributes to determining the number of CCD stages required to recover the desired amount of soluble metal. Furthermore, similar results could be achieved at a lower wash quantity, reducing the size of downstream equipment. High density thickeners (HDT) are designed to use gravity and compression, and minimize the amount of liquor in the underflow thus minimizing the number of CCD stages. This paper reviews the process used to select HDTs rather than high rate thickeners (HRT) for the Ruashi II copper-cobalt hydrometallurgical process in the Democratic Republic of Congo (DRC), using laboratory HDT simulations, to CCD simulations and thickener design details.

Jan 1, 2009

The results of small-scale resin-in-pulp pilot-plant investigations at Grootvlei Proprietary Mines Ltd, President Brand Gold Mining Co. Ltd, and Western Areas Gold Mine Co. Ltd are reported. At each mine, a pulp was fed simultaneously to a carbon-in-pulp plant, allowing a direct comparison of the metallurgical performance of the two processes. With the Grootvlei pulp, gold was extracted more efficiently by resin than by carbon owing to the Iow concentration of competing base-metal cyanide complexes in solution. With the Western Areas pulp, the reverse was true because of the high concentrations of copper and nickel in solution. Finally, with the President Brand pulp, resin-inpulp was significantly superior to carbon-in-pulp owing mainly to the inherently slow rate of gold extraction from calcine by activated carbon. Results are presented that show the efficiency of the elution of gold and other elements with a variety of reagents from the loaded resins arising from these three campaigns. At Western Areas, a detailed investigation enabled a preliminary cost evaluation to be made of three techniques for the elution of strong-base resins.

Jan 1, 1984

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By J. M. Stewart

Mining fatality rates in many countries have not changed substantially over the past ten years. This demonstrates not only that there is an inherent risk in mining, but also that current approaches to improving safety need to be rethought. An analysis of productivity and fatality data in the United States, United Kingdom, and South 4frican coalmining industries shows that the impact of legislation on safety is overlain by other significant factors. Although improvements in safety and productivity usually occur together, the data warn that safety legislation can sometimes cause a significant reduction in productivity. Based on the data and experience considered, it is concluded that legislation should be aimed at creating a framework within which a positive attitude towards the implementation of more productive and safer mining methods, work practices, and technology can flourish, rather than attempting to enforce excessively prescriptive provisions. This later approach is even more problematic when safety standards and legislation are transferee from well developed to less developed countries. A legislative framework in which the mine manager is required to take al reasonably practicable measures to procure safe working conditions in accordance with mine-specific codes of practice is outlined. Within that framework, the value of adopting widely accepted standards is recognized. A performance-based external audit arrangement is outlined as a basis for ensuring that detailed attention is focused on those areas most needing improvement.

Jan 1, 1995

By W. D. Grimsley, R. P. King, J. B. See

Samples (15 to 20 g) of pre-calcined Mamatwan manganese ore or pure Mn 304 smaller than 48 mesh were reacted at temperatures in the range 1000 to 1300°C with samples of spectrographically pure graphite smaller than 325 mesh. Samples (1 g) of ore or pure Mn02 smaller than 48 mesh were reacted at temperatures of 1000 and 1200°C with pure graphite fines in argon, with graphite in carbon, .&apos;1onoxide, and with carbon monoxide alone. In each case, the loss of mass as a function of time was recorded with a hermobalance. The rate and degree of reduction were found to increase with additions of carbon and with increasing temperature up to 1300oC, when they reached their maximum. The shape of the reduction curves, together with the results obtained from examination of the products of reaction by microscopy and X-ray diffraction, were used as the basis for a postulated reduction mechanism. Some details are given of an initial kinetic model that was used to verify the proposed mechanism. It was found that the reduction of Mamatwan ore by graphite at temperatures in the range 1000 to 1300°C occurs in two stages: (i) an initial stage during which the higher oxides of manganese are rapidly reduced to MnO with concurrent formation of CaMn2O4 and (ii) a longer stage during which CaMn2O4 and MnO are reduced to carbides by carbon dissolved in the ferromanganese phase.

Jan 1, 1978

By D. Duncanson, R. J. Davidson

The elution of gold from activated carbon using deionized water by R. J. DAVIDSON, M.Sc., Ph.D. (Rhodes) (Visitor) and D. DUNCANSON, H.N.C., B.Sc. Hons. (Strathclyde) (Visitor) The pretreatment of gold-loaded activated carbon with a relatively strong sodium cyanide solution prior to elution with deionized water at 90 to 125°Chas been shown to have a most beneficial effect on the elution of gold. The findings emphasize the important role played by the calcium cation and the hydroxyl anion in effecting efficient elution of gold. The elution of the relatively unstable complexes of silver and base metals with cyanide was also significantly affected by the ratio of the sodium cyanide to sodium hydroxide in the reagents used in the pretreatment stage. It was demonstrated that the use of 0,5 bed volume of a pretreatment reagent comprising 10 per cent sodium cyanide stabilized with I per cent sodium hydroxide for safety reasons resulted in a virtually 100 per cent recovery of adsorbed gold, silver, and base metals on subsequent elution with deionized water. The elution procedure takes a relatively short time, about 14 hours at 90°C (7 bed volumes) or 3 hours if pressure elution at 125°C (4 to 5 bed volumes) is used. Because the mechanism of elution after pretreatment entails the shifting of a physical rather than a chemical equilibrium, the higher the gold loading on the activated carbon, the more efficient is the elution procedure. When compared with other elution procedures, the proposed method appears to have several economic advantages.

Jan 7, 1977

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

In the previous chapters we did not concern ourselves with the fact that the geostatistical properties of the regionalized variable x (z) are affected by the size of the support w. Ideally, when analysing an ore body O, we would like to determine the properties of point values in O, i.e. the properties of a regionalized variable with an infinitely small support, say w°. In practice, point values are never known. To measure the value of x at a point z we must take a sample of size w centred at z. For example, if we are interested in the grade at point z, w will be the volume of the sample &apos;centred in z; if we are interested in the metal accumulation at point z, w will be the area of the cross-section of the sample centred in z. We say that the measured property is a regularized variable, and so the semivariogram (or covariogram) calculated from the values obtained is also regularized. In the majority of the mining problems which can be solved by geostatistical methods, we are interested in the properties of blocks of ore and of samples with a finite non-point support. It will be shown in the following chapters that these problems can be solved by calculating the average value of the point sernivariogram in volumes or areas of finite dimension, or between such volumes or areas. These calculations would be simple if we knew the point semivariogram. This means that the point semivariogram has to be estimated from the observed regularized semivariogram(s).

Jan 1, 1978

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.

By H. J. de Klerk

The metallurgical phenomena in the design and manufacture of high-strength low-alloy (HSLA) steels are reviewed, and some aspects of the production of Supraform TM (thermo-mechanically processed) steel are discussed. . The weldability of Supraform TM is related to changes in the microstructure of its heat-affected zone.

Jan 1, 1984

By M. J. Robinson, G. E. Blight, J. A. C. Diering

The mechanism of the flow of tailings slurry is examined, and a mathematical model is derived to describe the flow. Predictions based on the model are then compared with the flow that actually occurred near the shaft at Bafokeng after the No. I tailings dam had failed. The predictions are found to be of acceptable accuracy.

Jan 1, 1981

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.