Search Documents

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By J. P. De Carvalho, R. Dimitrakopoulos

This paper presents an actor-critic reinforcement learning (RL) method to allocate trucks and shovels in open-pit mines, while defining short-term production scheduling of an industrial mining complex, given new information collected during operations. This new data obtained from sensors update the uncertainty of the orebody models. The RL agents interact with the mining complex environment; exploring the solution space, learning actions to improve metal production and equipment utilisation. A case study is presented at a copper mining complex, highlighting the method’s ability to adapt and make informed decisions while collecting new information.

Sep 1, 2021

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By M. Reuter

This paper gives an overview of some criteria for the selection of processes for the recovery of lead and zinc from various raw materials and/or intermediate products. A glossary of possible processes and process variants, is presented and discussed, as well as the way in which these are interlinked. Recent developments in metallurgical process synthesis are also discussed, and the results produced by an eco-techno-.economic synthesis procedure for process routes in zinc metallurgy are given briefly. The way in which such a synthesis can complement a life-cycle assessment (LCA) of zinc-producing technologies is also described.

Jan 1, 1997

By P. E. Hand

SYNOPSIS This paper describes some of the markets for South African coal and their particular coal requirements. It describes how reserves are being used and suggests new strategies to make possible a synergistic ap¬proach that would benefit coal producers and end-users.

Jan 1, 1991

By S. Carter

this paper describes an innovation in computer software that permits mining professionals to collaborate on exploration and mining projects regardless of geographic location. Growth of mining companies through merger and acquisition has created a greater need for mining professionals to collaborate, especially as projects and project participants are becoming geographically remote. Surpac NetVision, the name given to this new collaboration technology, satisfies this need by deploying interactive 3D graphics sessions across computer networks. It achieves this by using common web browser technology as the deployment medium. A plug-in architecture that supports diverse file formats permits transparent read and write of foreign data to further enhance the collaboration process. Surpac NetVision supports any number of connections from web browsers on remote computers using existing networks. Software components required to enable the collaboration session are deployed to the remote computer as required and cached for future sessions. The collaboration session at each computer is characterized by a fully functional replica of the user interface for Surpac NetVision from which any function can be executed by any client, at the owners discretion. All geometry and display attributes deployed to remote clients to render 3Dgraphics are highly compressed to reduce bandwidth requirements. The key benefits of this collaboration technology is improved communication in regard to exploration and mining projects leading to: •More informed decision making •Improved deployment of project objectives and plans beyond the technical planning group to project management and operations staff •Improved technical support for software users. Keywords: 3D graphics, project collaboration, interactive graphics, internet 3D graphics, mining software

Jan 1, 2003

By R. J. Mostert

The role of hardenability in the development of high-strength low-alloy (HSLA) steels is discussed. The applicability of the superhardenability treatment. a steel making technique for increased hardenability, to HSLA steels is indicated, and the literature on this treatment is reviewed. Several low-carbon superhardenability HSLA steels were designed by use of published superhardenability multiplying factors. It was found that the hardenability of these low-carbon steels can be increased to the same extent as that of medium-carbon steels. The mechanical properties as determined in normalized bars indicate that the superhardenability treatment can be used successfully in the production of low-carbon hot-rolled HSLA steels.

Jan 1, 1984

By M. Bryson, V. Deeplaul

As a national facility, Mintek?s brief is to conduct high calibre research that allows the most effective utilization of South African resources. The research takes two different forms, with the efforts being directed at both high-risk endeavours that may lead to the development or adoption of new technologies or the reapplication of technologies to potential new operations. Starting in the 80s Mintek began developing a process to upgrade the UG2 ore and invested heavily in projects, equipment and people to service the industry. Some of the highlights of that work that has been conducted here include: ?Development of a milling and flotation process for UG2 ores ?Development of the ?Mintek Process? for maximizing PGM recovery for UG2 ores ?Conversion of the UG2 milling circuits to open circuit ?Development of a robust pilot plant facility for use in plant design studies ?Use of dense media as a waste rejection option ?Use of attritioners in flotation circuits. More recently, and with the future in mind, the following processes are being researched, some of which have already been commercially applied: ?Development of a flowsheet for Platreef ores ?Use of optical sorting technology for upgrading platinum ores ?Use of a mini-plant for reagent optimization studies. Each of the highlights listed above will be discussed in the paper.

Jan 1, 2004

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By P. R. Jochens, D. D. Howat, C. W. Wolhuter

Prof D. D. Howat (Member): I am a man with a grievance this afternoon. The other authors of the paper entered into a conspiracy to ensure that I presented the paper, and finally even had the audacity to say that this was the least that could be expected from me as I had done so little of the other work. Looking at the distinguished audience here that includes some figures who have forgotten more about cement that some of us have ever learned, I realise how right the other authors were. I feel very much cast in the role of the fool who was pushed in where angels fear to tread. I hesitate to say, Sir, that I would not use the word angels in any definition of the authors of this paper. In presenting the paper, may I try to put forward a few simple points about cement that are probably as little known to the majority of the audience as they were to me-at least until very recently. Concrete, made by mixing Portland cement, sand, crushed rock and water is the most widely used constructional material in the world. Generally the production of actual Portland Cement is about two-thirds that of steel and by the time this is formed into concrete the total is about five times the world tonnage of steel produced. A very rough approximation suggests that world consumption of concrete is about one ton per person per annum. Apart from fresh water mankind consumes no other material in such quantities. What mankind originally required was a mortar to be used for joining blocks of stone or bricks. Such mortar was originally made from limestone burned in a kiln and then mixed with water. Production of mortar of this type began over 5,000 years ago. Some samples from pyramids in Egypt have shown this mortar to be in good condition although over 4,500 years old. The progress of technological development was very slow until 1824 when an English bricklayer, Joseph Aspidin, patented a new mortar material which he made by burning limestone and clay together in his kitchen stove. Aspdin called his product 'Portland Cement' because, in colour, it resembled a well-known building stone quarried in the Isle of Portland on the south coast of England. Aspid's same types of raw materials are used today in modern cement production and the product is still referred to as Portland cement. A lime-containing material such as chalk or shell and a clay-type material such as shale, slate or clay itself, are mixed in the required proportions, ground and fed to a kiln where the minimum burning temperature is about 1,500°C. The raw materials react to form hard chunks of a material known as 'clinker'. About 5 per cent of gypsum is added to the clinker and the mixture is then ground to a very fine powder, the function of the gypsum being to control the rate of setting of the concrete. The key oxides in cement production are lime, silica, alumina and iron oxide. The possible reactions occurring during and the products of the burning process are shown in Table I.

Jan 12, 1968

By J. Petersen, K. Shaik1, H. Kolev, Z. Cherkezova-Zheleva

Sperrylite is one of the most abundant platinum minerals globally, valued for its economic importance but also known for its highly refractory nature, making it difficult to process via the conventional route. This study explores the oxidative leaching of sperrylite using a cyanide–ferricyanide system, with a key focus on characterisation of the mineral and surface speciation under varied leaching conditions using x-ray photoelectron spectroscopy. The parameters investigated include the effect of sodium cyanide concentration, the use of potassium ferricyanide as an oxidant, copper sulphate pentahydrate as a catalyst, as well as the effects of temperature and particle size. A limited set of leaching tests was carried out to study the surface chemistry rather than optimising dissolution conditions. This approach identified mineral oxidation states and shifts in binding energies, prior to and post leaching. XPS analysis of sperrylite’s surface chemistry identified key species, comprising the bulk Pt(II)–As (≈73 eV) and As(–I)–Pt (≈41.8 eV) states, together with surface oxidation products Pt(II)–O (≈72 eV), Pt(IV)–O (≈74.5 eV), As(III)–O (≈43 eV) and As(V)–O (44.5 eV). Leaching led to the removal of pre-existing oxides on the ultra-finely ground sample, exposing the underlying bulk species. In contrast, the crystalline sample with an initial low concentration of oxides, generated higher amounts of fully oxidised species after leaching, reflecting greater surface reactivity.

Mar 6, 2026

By H. A. D. Kirsten

The skills differential between manpower supply and demand is due to deeply rooted socio- and politico-educational misconceptions that can be remedied only by a concerted cooperative effort on the part of the general public, the State, organized industry, organized engineering, and engineering education. This will require the general public to recognize that the reasons for the shortages in engineering manpower should be regarded as critical. Public perceptions of engineering, of the vocational and educational prospects in engineering, and of the skills required are poor. The spectrum of engineering vocations, the corresponding function profiles, the interaction between the vocations and the relative proportions of the vocations in the engineering team are in general not adequately appreciated. The recruitment and training of students and teaching staff, teaching facilities, educational curricula, practical training, qualifications, professional registration, and financing are aspects of engineering education that should be brought to the attention of all concerned. . In addition, the educational curricula for the various vocations need to be specified clearly and definitively if the overall mission of engineering education is to be properly appreciated. The uncertainties between university and technikon education and the pursuant vocations need to be resolved. This can be done only by defining the respective curricula in terms of the mental skills and scientific techniques required. The remedial actions with regard to the rationalization of engineering education comprise informing of the public; establishment of an active political lobby; revision of existing education policy; rationalization of existing educational infrastructure; promotion, development, and guidance of engineering student intake; financing of engineering education; accelerated creation of new employment opportunities; and monitoring of the supply and demand of high-level manpower. The parties required to nitiate these remedial actions are various State departments and corporations involved in engineering and industry, various departments of education, the Directorate of Technology of the Department of Trade and Industry, organized engineering education, organized engineering, organized industry, and the Human Sciences Research Council. Only if these interest groups actively initiate the various actions under the coordinated guidance of organized engineering wil the required results be achieved. The South African Engineering Association has proposed a comprehensive programme as strategy to solving the problem, and has obtained broad consensus from various State departments, organized engineering education and research, and the private sector. A joint venture between the Foundation for Research Development, the South African Engineering Association, and organized industry has been charged by the State President with the task of launching the programme.

Jan 1, 1991

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996

By R L. Bowers, D S. Smit

In light of soaring commodity prices, Nkomati has investigated the potential of processing additional low grade nickel ores to add to their reserves. The Chromititic Peridotite Mineralised Zone (PCMZ) was identified as one ore type with the potential of producing a high grade nickel concentrate. In addition to the nickel, copper, cobalt and PGM?s, the ore also contains a significant amount of chromite which adds substantial value to the project. Pyrrhotite, pentlandite, chalcopyrite and chromite are the dominant minerals within the ore, which on average grades around 0.23% Ni and 12% Cr2O3. The PCMZ ore contains excessive amounts of fibrous silicates which makes it a challenging float, with gangue control as the key element to success. Extensive laboratory testwork, which eventually led to a pilot plant campaign, was undertaken with the aim of developing a process route for treating the PCMZ ore. Several flotation circuit configurations were tested and results from the optimal circuit indicated that a nickel concentrate grading at 8.5% is achievable at a recovery of 78%, with substantial recoveries for the copper, cobalt and PGM co-products. The chromite concentrate, grading at 45%, was extracted from the flotation rougher tailings via a spiral plant. These promising results were incorporated into the plant design and are currently being evaluated in a bankable feasibility study, which will see the current 100ktpm MMZ concentrator being upgraded to a 250ktpm PCMZ concentrator as part of Nkomati?s Phase II expansion.

Jan 1, 2007

By H. W. Glen

The National Institute for Metallurgy - usually referred to as NIM - has become the Council for Mineral Technology, or Mintek. The Honourable F. W. de Klerk, Minister of Mineral and Energy Affairs, announced the change of name at the official opening of the main entrance to Mintek's premises on 30th October, 1981. Awards for bravery Two men who disregarded the dangers of fiercely burning timber and falling rocks to douse an underground fire, using their hard hats to scoop water from a drain, received the Chamber of Mines Award for bravery at a ceremony held at West Driefontein Gold Mine near the end of October.

Jan 1, 1981

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By R. Ciccu

This paper examine the optimization of a beneficiation plant for recovering marketable barites from crude ores of different characteristics. The plant, part of a mining complex in Sardinia, consists of a jig section integrated with a flotation line. The problem has been studied using a suitable model of the process, based upon experimental and field data pertaining to both the characteristics of the feed material and the performance of machinery. Data have been automatically processed with the aid of a computer to find the optimum setting of each section, in order to maximize profit for each kind of ore separately fed to the plant. Moreover, the advantages of blending the various concentrates - not all of them individually marketable - are also demonstrated. The overall economic result can be improved provided suitable proportions of each kind of ore are fed to the plant. Such information is fundamental for the long-term planning of exploitation of available reserves, and provides guidelines for further prospecting. The paper illustrates the washability characteristics of the ore's and describes in detail the model adopted. The results of data processing are then presented in the form of computer graphs and discussed. Finally, conclusions are drawn regarding the advantages of resorting to Operations Research as an aid to management.

Jan 1, 1987

By T. Vincent, J. Steele, C. Debrunner, M. Whitehorn

This paper presents current work on the development and use of stereovision for underground mining. Information on the calibration of the cameras and the feature-matching algorithm are presented. This system uses an intensity-based approach that evaluated correspondences along the epipolar line. Once features have been identified and their distance from the cameras computed, a three-dimensional map of the muck pile is developed. The approach used here uses a ray-tracing algorithm. This approach provides an uncertainty measure along with the elevation. A discussion of the use of this modelling information in the control of the LHD is included. Keywords: Robotics, automation, LHD, underground mining, vision sensing, task automation, tele-operation

Sep 1, 2001

By M. Wu, X. Zhao

This paper presents an integrated pipeline transport system for thickened coal sludge, which combines pretreatment and pipeline transport with combustion techniques of thickened coal sludge. The pipeline can transport thickened coal sludge with a sufficiently high solids content (about72%?77%) and high apparent viscosity (about 1 000Pa?S?3,000 Pa?S) directly by pipeline having neither use for water nor an addition agent. The transport distance can be as high as 1 000 metres. In particular, the operating principles, key equipment and technical parameters of this integrated system are examined in this paper. The integrated system effectively causes no pollution to the environment because it is completely sealed, and conserves energy over traditional conveyer designs. Keywords: pipeline transport; integrated system; circulating fluidized bed boiler; thickened coal sludge; high solids content

Jan 1, 2007