Search Documents

By L. C. Woollacott, A. K. Tripathy, J. H. Potgieter

This paper presents the second of a two part study on density stratification in a laboratory batch jig. The first study, reported elsewhere, investigated the effect of operating conditions on the stratification profile achieved at equilibrium. The study reported in this paper investigated their effect on the kinetics of density stratification under 18 different sets of operating conditions - five for binary systems with different particle densities; and 13 for a ternary system with different configurations of the jig cycle. Although the study was academic in nature (it involved simple systems of 8 mm glass beads) it has a number of practical implications. It found that the most influential operating variables affecting stratification kinetics are the amplitude of water displacement, the pulsion hold time, and, to a lesser extent, the pulsion time. It also found that reasonable rates of stratification can be expected in systems with density differences as low as 237 kg/m3 but below this the kinetics deteriorate significantly. The two studies together suggest that, within a broad range of operating conditions, the equilibrium stratification profile is independent of control variables and it is the control of stratification kinetics that has the primary influence on the quality of density separations in a jig. Keywords: Jigging kinetics, stratification, equilibrium stratification, batch jig

Jan 1, 2020

By D. Amariei, G. Bartolacci

Preconcentration of precious and base metal ore types is becoming more relevant with the discovery, the development and the operation of many lower grade deposits around the world. Ore preconcentration designates an operation consisting of sorting an ore to reduce the quantity of waste material sent to the concentrator. It can be seen as rejecting waste material as much as possible, without compromising the recovery, or as the recovery of as much valuable metal as possible into an optimum mass yield. Benefits of preconcentration are multiple: grinding energy savings, costs reduction, lower environmental footprint, extension of the reserves, etc. However, all of these benefits do not apply simultaneously and are not applicable to each ore type. Technologies employed for preconcentration are highly dependent on ore properties, especially on the particle size at which the gangue is liberated. Thus, from coarser to finer particle sizes, technologies such as screening, ore sorting, gravity separation (Dense Media Separation (DMS) and jigs) and coarse flotation could be used for the rejection of liberated gangue. The difficulty starts when a benchmark is needed to select a suitable technology, especially for low-grade gold deposits. This paper presents the challenges of comparing lab-scale technologies (DMS versus jig) for gold preconcentration. The experimental data will show to what extent comparing two lab-scale gravity technologies for gold preconcentration can be challenging. An attempt to evaluate the energy savings by assessing the hardness of the tailings after gravity separation will also be presented. Keywords: Challenges in gold preconcentration, gravity separation, jig, dense medium separation

Jan 1, 2020

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1975. Professor R. P. Plewman (President) was in the Chair. There were present 45 Fellows, 37 Members, 8 Graduates, 3 Associates, 4 Students, and 45 Visitors, making a total of 142. The President declared the Meeting open at 16h00. OBITUARIES The President: Ladies and gentlemen, it is my sad duty to announce the death of the following members of the Institute : M. Barcza, an Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep, and J. H. Taylor, Life Fellows ; I. D. B. Corner, C. O&apos;G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin, and F. S. Steinhobel, Fellows; J. J. Frankel, Member; and T. J. Higgs, Associate. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I ask you to rise and observe a few moments&apos; silence. MINUTES The President: May we confirm the minutes of the General Meeting held on March 12th 1975 and published in the June issue of the Journal? Agreed. WELCOME The President: It is now my very great pleasure to welcome the many members of our Institute and all the distinguished guests who have honoured us with their presence this afternoon. In particular, I would like to welcome our Honorary President, Mr R. S. Lawrence, President of the Chamber of Mines, and also our Honorary Vice-President, Mr T. L. Gibbs, the Government Mining Engineer. Ons is ook besonder vereer dat dr. Naude, die Wetenskaplike Raad-gewer aan die Eerste Minister, en mnr. C. A. J. Borman, Direkteur van die Witwatersrandse Kollege vir Gevorderde Tegniese Onderwys, hier aanwesig is om die vergadering by to woon. We are also honoured by the presence of some 19 Presidents, Vice-Presidents, and Chairmen of our sister scientific and technical organizations. I would particularly like to welcome Mr Gericke of the South African Council for Professional Engineers, Professor Pretorius of the A.S. & T.S., and Dr Lloyd of F.S.P.E. And then, also the Presidents of the Institute of Welding, Professor Robinson; of the Electrical Engineers, Dr Troost ; of the Certificated Mechanical and Electrical Engineers, Mr Gibbs; of the Geological Society, Professor Maske; of the Land Surveyors of the Transvaal, Mr Course ; of the Assayers and Analysts, Mr Williams; of the Mine Ventilation Society, Mr Martinson; of the Chemical Institute, Mr Goodman; of the Association of Mine Managers, Mr Pretorius ; of the Institute of Foundrymen, Mr Attenborough; of the Production Engineers, Mr Duggan ; and of S.A.F.U.E.S., Mr Avalle. Then, the Chairman of the Council of the Institute of Metallurgists, Mr Snow; the Vice-President of the Town and Regional Planning, Mr Reinecke; the Vice-President of the Association of Consulting Engineers, Mr O&apos;Kell; and Mr Cronje, who is representing E.A.S.A. Finally, the Chairman of the Southern Transvaal Section of the Chemical Institute, Mr Bloom ; the Chairman of the Witbank-Middelburg Branch of our own Institute, Mr Hosking; and the Secretary-Treasurer of our O.F.S. Branch, Mr Bird. We also have with us Mr Trueman; the Deputy Manager of Kelvin House, Mr Mrost ; our Honorary Editor, Dr Glen; Mr Walford; and also some representatives of the Press. Finally, it gives me great pleasure to welcome those who will receive Honorary Life Fellowships tonight, and also the winners of our student prizes. MEMBERSHIP The President: Ladies and gentlemen, I have pleasure in announcing the names of the following candidates, which have been published in accordance with By-Law 5.2.5., and Council has elected them to membership in the following grades: Fellows: R. G. Boswell, R. W. Chadwick, D. R. Hardman, J. A. Holmes, T. J. B. Jones, and R. P. King. Members : M. A. Bridgeford, C. F. Bonney, H. E. Bartlett, L. G. Floyd, A. K. Haines, D. Hatfield, C. G. Heymann, M. J. Howes, J. B. See, E. van Greunen, and S. P. Swanepoel. Associate Members : J. Coetsee and R. P. G. Steyn. Graduates: J. J. de Villiers and J. C. King. Associates: B. J. Bucher, P. A. Combrinck, W. J. N. Gelderblom, L. S. Halasz, J. van Wyk, C. P. Visser, and A. Veress. Students: D. J. Claasens, P. C. Crous, D. H. Murchison, P. A. Rossouw, and J. P. L. Schultz. Company Affiliates: Airco Engineering (Proprietary) Limited and Deelkraal Gold Mining Company Limited. There have also been some transfers: Member to Fellow: J. B. Nangle. Graduate to Member: E. E. Eichenbergen, M. J. Hillbeck, L. A. Melis, P. J. Venter, and R. O. Wellman. Associate to Associate Member: B. M. Williams. I welcome the newly elected members to the Institute, and I congratulate those who have been transferred to a higher grade.

Jan 10, 1975

By T. Szendrei, S. Tose

The Gurney approach to explosive/inert material interaction was adapted to analyse the face velocity in bench blasting. The model is based on the blasthole diameter, rock and explosive density, burden, spacing, linear charge density, and the Gurney energy constant. It is validated by comparing its predictions with a set of 20 field measurements of face velocities reported by Chiappetta et al. (1983) in an iron ore mine. The Gurney model links the observed large scatter of measured face velocities to the variation of the Gurney energy constant. This in turn is linked to the variability of the gas pressure acting on the burden. These variable pressures are generated when detonation product gases migrate into the extensive and complex fracture network around and between in-row blastholes. The energy efficiency of burden movement can be derived from the model. It is shown that ~7% of the explosive’s chemical energy is available for gas expansion work on the burden; of this quantity, 36% is actually converted to burden kinetic energy. That is, less than 3% of chemical energy is ultimately expended in burden displacement and throw. The model further indicatesnthat the projection of high-velocity (say, 100 m/s) flyrock is possible only when the path of leastnresistance through the burden has an effective density far less than the host rock. An equationnis derived that identifies the combinations of burden and path density that may yield flyrock. These values are specific to a particular baseline blast design.

Jan 30, 2026

By Y. G. Zhu, G. B. Zheng, X. X. Hu

Reverse flotation by cationic collectors is the classical method to reduce the silicon content in magnesite. But because of the low selectivity, there is a large loss of magnesite in the reverse flotation froth. To improve the efficiency of the collector, a novel collector named BK433 was developed in this paper. In order to determine the performance of the BK433 collector, a systematic experimental study was carried out with a high silicon magnesite in China. The suitable pH environment of slurry was confirmed, the depression effect of different depressants was investigated, and the flotation effect was compared with commonly used traditional collectors. The results show that the BK433 shows remarkable good selectivity and collection ability. After the 4 stages reverse flotation, the SiO2 content decreased from 3.76% to 0.25%, SiO2 impurity removal rate reached 94.69%. Meanwhile, the MgO content increased from 45.06% to 46.73%，the recovery of obtained concentrate (calculated by MgO) was 82.79%. Keywords: Magnesite, Desilicication, Reverse flotation, Collector

Jan 1, 2020

By A. J. Rogers

The KX36 kimberlite was discovered using a high-resolution gradient aeromagnetic survey, with follow-up detailed ground geophysics and deflation soil sampling used to assess and prioritize the geophysical anomalies identified from the initial aeromagnetic survey. Prospect drilling intersected kimberlite in the first hole drilled on the KX36 anomaly. Preliminary evaluation has shown that KX36 is diamondiferous, and a more detailed evaluation and sampling programme is currently underway. The area around KX36 has been prospected by numerous companies over the last few decades, with sporadic kimberlite indicator mineral (KIM) recoveries in regional deflation sampling indicating the possible presence of kimberlites, but without sufficient resolution to ?home in? on specific targets. Previous (lower resolution) aeromagnetic surveys and soil sampling campaigns also did not define anomalies with sufficient detail to guide prospect drilling effectively. The discovery of KX36 highlights the prospectivity of areas of Botswana under deep Kalahari cover that have been explored previously. Keywords kimberlite exploration, central Kalahari, overburden, high resolution aeromagnetics, deflation sampling, KIM.

Jul 1, 2013

By B. Genc

Safety in South African mines is a subject of significant interest, since many mining companies are experiencing production deficits due to safety-related stoppages. In this paper, safety data from the South African platinum mining sector is analysed for the period 2006 to 2010. The data was obtained from company annual reports as well as the Department of Mineral Resources, and analysis in the study is limited to injury and fatality data only. The overall safety performances of companies in the sector are compared, and opportunities for benchmarking and recognising potential sources of best practice amongst platinum miners are identified. Improving safety usually incurs a cost, and mining companies are particularly conscious of the importance of controlling costs. However, cost considerations often deal only with direct costs, and it has been shown that indirect costs are usually far more significant. Therefore, a greater safety spend will usually result in the creation of value for the mine since it will reduce the indirect costs associated with accidents. The results of some recent research in this area are presented. In this light, where available, the financial performances of mining companies in the sector, obtained from published annual results, are included in the benchmarking exercise to determine whether there is any correlation with safety performance.

Jan 1, 2012

By C. A. Rawlins

Deep underground mines use refrigeration systems to provide a reasonably comfortable ambient environment to increase productivity and to maintain safety as a priority. Deep level gold mines maintain the environment at an acceptable temperature, i.e. 27°C. However, the increasing cost of doing so through refrigeration is becoming a significant factor in the economic viability of mines. This paper discusses of the important facet of energy losses in cooling reticulation systems, laying with the specific emphasis on the subject of chilled water transport pipe insulation and its thermo-dynamic relationships. Aspects relating to the deterioration of open cell-type insulation materials such as polyurethane/styrene foams and the use of Phenolic resins that have good fire retardation properties have been investigated. The thermal conductivities of these insulation media are good (meaning below 0.05 W/°C)However, they are known to be negatively influenced by water vapour ingress and vapour pressure differences that result in the ingress of water into the material by means of absorption, condensation, hygrospicity, permeability and capillary action, to name a few of many. The overall effect on mine cooling efficiency takes in the two forms: first by the loss of refrigeration or increased chill in the water temperature arriving in a given section and second, by a loss in transfer efficiency when the gap between the arriving water temperature and the actual air temperature decreases. Keywords: Conductivity, vapour, insulation, fluid, thermal, temperature, pressure, transport, refrigeration.

Jan 1, 2007

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway Operations&apos; 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. D. Ahmadabadi

The main challenges in most low grade iron ore deposits are finding the optimum flowsheet for beneficiation to achieve a final concentrate from both technical and economic viewpoints. Dry preconcentration techniques are being used to assist in reducing the amount of ROM feed to the plant. In this paper the benefits of utilising a dry cobbing magnetic separation technique for upgrading the product of HPGR in a closed circuit with dry screen 4 and 1.4 mm by performing a pilot scale test work was investigated. The experimental test work was done on two sample types of Yogi BIF magnetite iron ore located in Western Australia. Prior to magnetic separation studies, detailed characterisation of the feed materials including physical, chemical, mineralogical and magnetic properties were carried out. Furthermore, the effects of process parameters: drum rotation speed (1.5, 2.5 and 3.5 m/s), magnetic field intensity (1100 and 3800 gauss) and feed size (minus 4 and 1.4 mm) were investigated. The results revealed that sample type1 with 33.90% Fe could be upgraded to 41.51% Fe by using a stage of 1100 gauss dry magnetic separator with 69.12% weight recovery and 84.36% Fe recovery at a size of 4 mm. Also for sample type2, it is possible to increase Fe grade from 29.84% to above 36.68% with 75.58% weight recovery and 90.32% Fe recovery by applying one stage of 1100 gauss dry magnetic separator to a 4 mm size sample. Keywords: Banded iron formation (BIF), pre-concentration, dry cobbing technique, magnetic separator

Jan 1, 2020

By J. M. Stewart

The purpose of my few comments is to try to create a healthy perspective to constructively link considerations of the sessions to follow to those of the earlier sessions. I propose to do this by considering some of the issues and priorities related to the development of backfill systems and technology for South African gold mines.

Jan 1, 1988

By M. S. Moholwa, J. D. Steenkamp, H. L. Rutto

Manganese ores are the major source of manganese for the production of manganese ferroalloys. There is a gap in the knowledge of the decrepitation behaviour of manganese ores, which presents a problem in the operation of smelters. Decrepitation, which is the breakage of the ore particles upon heating, is an important quality parameter for these ores. The purpose of this investigation was to determine the extent to which South African manganese ores decrepitate during preheating in a rotary kiln. The effects of temperature, rotational speed, and particle size decrepitation were investigated. Manganese ores were heated in a laboratory-scale rotary kiln at temperatures of 600, 800, and 1000°C, and rotational speeds of 3, 6, and 12 r/min. The size ranges were +6-20, +20-40, and +40-75 mm and the residence time was constant at 30 minutes. The decrepitation index (DI) is quantified as the ratio of the mass of <6 mm particles after pre-heating to the total mass of the sample. It was found that the DIs for all ores used were proportional to the temperature and the rotational speed and inversely proportional to the particle size range with temperature being the most important parameter. Ore A was the most susceptible to decrepitation followed by ore C and ore B; this was mainly to the decomposition of kutnohorite, the content of which was the highest in ore A and the lowest in ore B.

Nov 30, 2022

By E. Bakhtavar

There are many near-surface deposits with considerable vertical extent that have the potential to be mined by a combined method of open-pit and underground methods. In this regard, there is often a point called ?transition depth? where a decision has to be made whether to continue deepening the pit or change to underground methods. Recently, optimization of the transition from open-pit to underground operation has become an important challenge in mining engineering. Optimally, to model the transition problem on the basis of maximization of the profit from open-pit and underground mining, (0-1) integer programming has been used. In this method, block economic values of open-pit and underground methods should be imported to the transition model. A hypothetical example is presented in order to assess the model in detail.

Jan 1, 2012

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025