Search Documents

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By L. K. Weaver

The objective of this study is twofold, The first is to present the composition of the offshore petroleum industry in terms of lease bonuses and the value of hydrocarbons produced from Federal offshore tracts. The second is to present costs of producing petroleum (oil and condensate) in the Gulf of Mexico with a financial analysis of an offshore operation. To prepare a financial analysis of an offshore operation, a model was derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block and the estimated income from the sale of the hydrocarbons produced. To establish cost and income guidelines for the model, a group of seven oilfields in the Gulf of Mexico ranging from 7 to 75 miles from shore and in water 20 to 130 feet deep was selected for study. A net profit or loss statement was prepared for each field and a discounted cash flow rate of return was calculated. Discounted cash flow rates of return for the seven fields range from 1.1 to 19.5 percent. Under the two specified conditions set up for the model (a 20-year and a 30-year oil depletion model), the rates of return are 17.2 and 13.7 percent, respectively. To January 1, 1959, the top four operators in the Federal offshore areas had paid approximately 40 percent of the amount spent on all lease bonuses and produced about 56 percent of the total hydrocarbons.

Jan 1, 1972

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By Eugene L. Grumer

High-expansion foam was applied to the flames of six fuels burning in a 1-foot-diameter tray. The flames of three hydrocarbon fuels were more readily extinguished than the flames of methanol, acetone, or unsymmetrical dimethyl hydrazine. The result is rationalized on the basis that heat transfer from flame to fuel surface is primarily radiative with the hydrocarbons and more largely convective with the nonhydrocarbons. INTRODUCTION Equipment for producing high-expansion foams has been developed by the Bureau of Mines to control coal mine fires.5 Recently such equipment has been redesigned for portability and has now been produced commercially for other fire-fighting applications. In May 1961, a 50-by 50-foot gasoline fire was extinguished within 2 minutes by a trailer-mounted foam unit that produced 12,000 cu.ft./min. of high-expansion (1,000:1) foam.6

Jan 1, 1962

By J. G. Donaldson

Nickel containing less than 0.01 percent of total metallic impurities was produced at the Rolla Metallurgy Research Center of the Bureau of Mines by electrodeposition from purified electrolytes. The first report on this research4 described purification of electrolytes by selective precipitation and by liquid-liquid extraction. This second report describes a procedure: or electrodepositing high-purity nickel from electrolytes purified by passing a nickel ammine solution through a column of an ion exchange resin. The nickel electroplated directly from the ammine solution without further treatment; a titanium cathode and two platinum anodes were used. The nickel deposit was dense, smooth, and adherent, and contained less than 0.001 percent each of cobalt, copper, and iron, and spectrographically detectable traces of aluminum, magnesium, and silicon. Nonmetallic impurities in the nickel metal were carbon and sulfur, each present in concentrations of less than 0.01 percent. The results of several experiments planned to purify solid nickel salts by zone refining are also reported. These salts, after purification, were intended for use in preparing electrolytes for deposition of high-purity nickel. Results were not encouraging so that the more promising ion exchange procedure was emphasized chiefly.

Jan 1, 1962

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By Gordon R. Sima, John L. Bennett, Roger L. King

Electric shocks are a serious problem in the mining environment. Because of extremely wide ranging use of electrically powered equipment in the mining industry, the hazard to personnel due to electrical shock and related injuries are not restricted to any single area but cover the entire spectrum of mining activity. Electrical accidents, resulting in personal injury, due to im- proper or complete lack of grounding of electrically operated mining machines, form a significant percentage of the overall electrical accident picture. The object of this paper is to describe methods of detection of unsafe electrical conditions with respect to the grounding of electrically operated mining equipment. It also includes a discussion of prototype instruments which effectively monitor the condition of the grounding safety devices currently in use on mining equipment and warn of dangerous conditions as soon as they appear. The paper is based on work accomplished under USBM Contract Number 50357115. The contract was initiated under the Pittsburgh Mining and Safety Research Center Program. It was administered under the technical direction of PM and SRC with Mr. Roger L. King as the Technical Project Officer. Mr. Daniel B. Dawkins was the Contract Administrator for the Bureau of Mines.

By Richard Havens

Acidic and basic uranium leach plant residues located on the Navajo Indian Reservation, Tuba City, Ariz., were successfully stabilized against wind erosion using a relatively low-cost chemical method. An elastomeric polymer chemical was applied to the dike areas and a calcium magnesium lignosulfonate to the beach areas of three tailings ponds. The water-soluble chemicals were applied with an automated sprinkling system. The stabilization cost was $335 per acre for the 34.5-acre tract.

Jan 1, 1969

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973