Search Documents

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By David E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surface underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material. Extended seismic arrays were used to identify the vibration characteristics within a few tens of feet of the blasts and also as modified by the propagating media at distances over 1 mile. Production blasts and specially fired single-charge blasts allowed the determination of natural ground frequency and the influence of initiation delay timing. Vibration amplitudes from the production blasts at all sites exceeded historical norms, particularly at the greater distances. This contrasts with the near-normal results from single-charge blasts. Apparently, between-hole time delays were insufficient to separate vibrations from adjacent charges for the low-frequency waves present. Single-charge tests showed that the propagating media produced low-frequency, ground-roIl-type surface waves at nearly all sites. Large blasts at such sites could produce an unacceptable risk of vibration-induced cracks in nearby structures.

Jan 1, 1989

By M. J. Mechling, H. J. Sloman

"INTRODUCTION The practicability of providing safer methods of underground transportation for mine workmen and officials has been given much thought in recent years by advocates of safety, health, and efficiency. Numerous fatalities and disabling injuries have resulted from falls of roof, personal contact with both electrical conductors and timbers, and improper position or conduct of passengers while they were in man-trips. Unfavorable atmospheric exposure due to high-velocity air currents and sudden changes in temperature may adversely affect the health of mine workmen if they are transported in unprotected Cars.Recent installations of protected, man-trip cars, wherein such cars have been utilized to haul men to and from their stations in the mine, have resulted in a large reduction in exposure to haulage hazards. Where special-built cars have been used the probability of injuries to men during transportation in man-trips has been decreased, and the morale of the employees has been improved. A number of man-trip cars are in service in the coal-mining regions; those described in this circular are typical examples of a few installations."

Feb 1, 1948

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978

To provide for continuous remote sensing of carbon monoxide (CO) in underground mines. The Approach A transducer module has been developed as a wall-mounted, continuously operating instrument that will measure ambient levels of CO, and produce a signal that is proportional to the concentration.

Jan 1, 1982

Rank the dust knockdown (airborne capture) ability of six different types of water spray nozzles, Approach A fixed quantity of dust is released into a large, closed chamber in a laboratory. Water sprays are turned on inside the chamber and their effectiveness on the dust cloud is evaluated from the rate at which the dust disappears. This method better simulates dust suppression underground than methods tried earlier. The results of the laboratory test were confirmed by conducting tests on a full-scale mod-el continuous miner face where dust levels were measured in the return airway. Results of the Closed Chamber Tests The graph indicates that atomizing nozzles provide the best use of water for dust scrubbing. However, use of these nozzles is limited by their susceptibility to damage and clogging. Hollow-cone nozzles perform almost as well as atomizing nozzles. Test results also indicate that full-cone, venturi-assisted, and flat-fan spray cones are about two-thirds as effective as hollow-cone nozzles. The least effective were venturi nozzles designed for moving air. The most significant advantage of hollow-cone nozzles over other nozzles tested is reduced clogging due to larger orifice size. The hollow-cone nozzle used in the test and depicted by the graph was type BD-3 manufactured by Spraying Systems Co., Wheaton, IL. This nozzle is already used on many continuous miners. Other hollow-cone nozzles of

Jan 1, 1982

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

By R. C. Ellman

Significant effects of in-the-mill drying on the pulverization of lignite have been demonstrated in an experimental impact-type pulverizer by tests in which the primary variable was temperature of the sweeping gas. Reduced power requirements and increased product fineness were observed as the extent of drying was increased. Pulverization with in-the-mill drying was studied in comparative tests made on lignites from five mine sources. All of the lignites responded in a similar manner; however, differences in the pulverizing characteristics of the individual lignites were significant. For one lignite, the electrical input to the pulverizer driving motor with minimum sweeping-gas temperature was 33.9 kw.-hr. per ton, decreasing to 14.0 kw.-hr. per ton with a sweeping-gas temperature of 658° F.; for another lignite, at comparable operating conditions, the electrical input decreased from 59.1 to 19.0 kw.-hr. per ton. In the first case, the product fineness increased with increasing temperature of sweeping gas from 65.2 to 79.2 percent through a 200-mesh sieve, and in the second case, from b2.7 to 86.9 percent through a 200-mesh sieve.

Jan 1, 1962

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By J. Douglas Causey

In 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a portion of the 110,000 acre Massacre Rim Wilderness Study Area (CA-020-1013). The area studied, containing 23,260 acres, is located in northwest Washoe County, Nevada, about 25 miles west of Vya adjoining the Charles Sheldon National Wildlife Refuge. Basalt caps older tuffaceous sedimentary rocks in an area that contains no claims or prospects. No mineral resources were identified during this investigation.

Jan 1, 1987

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By T. W. Goodman, J. Cervik

The Bureau of Mines conducted studies to compare the effectiveness of the cross-measure borehole system with that of surface gob holes on two successively mined retreating longwalls in the Lower Kittanning Coalbed. Only the cross-measure system was in operation on panel A; on panel B, both systems were in operation. In addition, the cross-measure bore-holes on panel B were drilled parallel to the face, whereas those on panel A were drilled at a 45O angle with respect to the longwall axis. The studies show that the cross-measure system captured 71 pct of the methane generated by longwall mining on panel A. On panel B, the sur- face gob hole dominated over the cross-measure system for about 700 ft (213 m) after it was intercepted. Beyond that point, the cross-measure system dominated. About 93 pct of the methane generated on panel B was captured by the two systems. Cross-measure boreholes that were drilled parallel to the face were as effective as boreholes oriented 45" with respect to the longwall axis. In addition, they are shorter and require less drilling time. Comparison between observed gas pressure differentials in boreholes and calculated values indicate that boreholes can be shortened further to 140 ft (43 m). Additional studies are needed to verify these calculations.

Jan 1, 1986

By G. W. Jones, R. E. Kennedy

"INTRODUCTION Information relative to the ignition temperatures of acetylene and acetylene-air mixtures has become of particular interest recently due to a number of explosions that have occurred in 500-pound, double-rated, medium-pressure acetylene generators in shipyards on the West coast. Various suggestions have been made as to the causes of these explosions prominent among which has been that air finds its way into the acetylene generators during abnormal operation or that air remains in the carbide hopper of the generator following the purging and charging operations.This raises the question as to how and to what extent the presence of small percentages of air in acetylene affects the ease of ignition of such mixtures at the various operating pressures of the acetylene generators. The range of operating pressures in the 500-pound, double-rated generators involved in the explosions may vary from below atmospheric to 15 pounds gage.The present report gives the results of an investigation made to determine the effects of pressure on the ignition temperature of pure acetylene and of acetylene containing varying percentages of air:EXPERIMENTAL Apparatus A preliminary investigation showed that a heated quartz surface gave lower ignition temperatures than other material tested.A ""hot-spot"" method of ignition was found desirable in the case of the acetylene mixtures since the violence of the explosions was reduced by keeping most of the test mixtures at room temperature. Explosive violence was reduced further by using an ignition tube 17 mm. or less in diameter."

Mar 1, 1945

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By W. A. Cole

The sulfur shortage that existed during the Korean conflict stimulated interest in coal measures as possible sources of sulfur. One of the areas brought to the attention of the Bureau of Mines was in Marion County, Iowa, where comparatively high-sulfur coals and other marcasite-bearing strata were known to occur. A Bureau of Mines engineer inspected the marcasite occurrence on December 4, 1954; this prompted further work on the Iowa coals and associated formations as a source of iron sulfides. An investigation of the Iowa high-sulfur coals was undertaken including core drilling, field reconnaissance, and compilation of data pertinent to consideration of the following: 1. Upgrading Iowa coal by mechanical cleaning and the feasibility of recovering sulfur from coal brasses. 2. Possibility of processing the high-sulfur coals by adaptation of methods employed in processing industrial gases to produce sulfur and sulfur products. 3. Possibility of finding concentrations of iron sulfides in associated rock formations in sufficient quantity for economical recovery.

Jan 1, 1957

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

Provide a coalbed methane data source for industry use in mine planning. Approach Coalbed methane data have keen collected and formatted into a computer implemented data base with software developed for storage, retrieval, and generating files of selected data in response to information requests and for statistical analysis of relationships among various coal parameters. How It Works Coalbed methane data is obtained by the Bureau's direct method test on exploration coal cores. The test involves sealing fresh coal cores in desorption canisters and periodically bleeding the gas into a water-filled, graduated cylinder to measure the volume of gas released. Coalbed methane data collected over the past 9 years have been entered into a computer-implemented data base for efficient retrieval and statistical analysis. Data base processing is accomplished with a commercially available storage, sorting, retrieval, and report writing software package (Datatrieve 11). Information requests from the coal industry are processed with the system, and the data in the desired output format am printed and forwarded to the requestor. Information such as coalbed name, location (state and county), depth of sample, gas content, and coal rank are available from the system. The data can be used for

Jan 1, 1982