Search Documents

Legislation and Government Programs.-On February 4, 1977, the Occupational Safety and Health Administration (OSHA) issued its final environmental impact statement on the occupational use of inorganic arsenic.2 The statement examined the ramifications of the original proposed standard published in the Draft Environmental Impact Statement (DEIS).3 The DEIS proposed to limit the exposure of employees to no more than 4 micrograms of arsenic per cubic meter of air as determined on an 8-hour-time-weighted average basis; or a ceiling limit of 10 micrograms of arsenic per cubic meter of air based on a 15 minute sampling period. The purpose of the proposed regulation is to reduce the risk of smelter workers developing lung and skin cancer as a result of exposure. A comprehensive study compiled by the Committee on Medical and Biologic Effects of Environmental Pollutants concluded that "there is strong epidemiologic evidence that inorganic arsenic is a skin and lung carcinogen in man."' In April 1977, the Environmental Protection Agency (EPA) served notice to ASARCO Incorporated that its Tacoma copper smelter and associated arsenic-producing facilities were in violation of State laws which limit sulfur dioxide and particulate matter emissions. This notice followed the Washington State Pollution Control Hearing Board overturning a prior ruling by the Puget Sound Air Pollution Control Agency (PSAPCA) which had permitted a 5-year variance from the State of Washington air quality standards. In December 1977, ASARCO appealed in court the decision of the Hearing Board.

Jan 1, 1980

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By W. W. Graff

This paper describing the mining practice at Mine No. 5 of the Marquette range, Michigan, is one of a series being prepared by the Bureau of Mines on mining practices, methods, tend costs in the various mining districts of the United States. The top-slicing system of mining, has been used ever since the present operating company took control of the property in 1903, the main level and sublevel layout being chanced only as local conditions required and the use of mechanical equipment increased.

Jan 1, 1930

Mining and reclamation procedures that meet the requirements of SMCRA are illustrated on pages 8 and 9 for each of the three major surface coal mining methods -- area mining, contour mining, and mountaintop removal mining. The three methods involve the same basic steps: clearing the land of trees and other vegetation, removing topsoil and overburden, mining the coal, and reclaiming the land. Although all three methods would not usually occur on any single site, the illustration facilitates comparison of mining and reclamation methods and aids basic understanding of the reclamation processes that take place under SMCRA. Area Mining The area mining method is commonly used to mine coal in the flat to moderately rolling terrain found principally in the western and midwestern states. After the overburden is excavated down to a coal seam, the mining area is enlarged horizontally to expose more coal for removal. In the West, where coal seams are commonly 10 to 20 feet thick (and range up to 100 feet thick in the Powder River Basin of Wyoming), the life of some mines maybe more than 50 years. In the Midwest, coal seams are typically 3 to 7 feet thick and 75 to 100 feet below the surface. Because of the large expanse of area mines and their relatively unrestricted sites, enormous equipment is used to remove overburden and reconstruct the land. The area mining operation in the illustration is on land that was formerly used for farming. The drawing shows that the agricultural use is being reestablished immediately following reclamation. Mining is proceeding across the land toward the left side of the site. The initial excavation was made far enough away from the stream along the right edge of the site to prevent damage to the water supply. The coal under most of the site has been removed, and reclamation has been completed on some of the land. For example, some of the cattle in the foreground and those in the feedlot behind the silo are grazing on reclaimed land that has been mined. At the far left of the illustration, topsoil from the unmined area is being removed by scrapers, transported across the area of active mining, and immediately spread on the land on the right, which is being reclaimed. (Reclamation of mined land as soon as practical, as required by the Act, is called contemporaneous reclamation.) A

Jan 1, 1992

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By E. J. Gleim

"Information gathered during recent months by field men of the U. S. Bureau of Mines shows that in one State alone there have been 71 fatalities from electrical causes during the last 51/2 years, of which 55 were from contact with mine trolley wires operated at 250 volts or less, direct current. The 1928 law relating to the guarding of trolley wires in the-mines of this particular State reads: ""All trolley wires carrying a voltage of class 2 must be properly shielded except where the same are at least 61/2 feet above top of rail."" Class 2 voltage is defined as being ""between 300 volts and 600 volts direct current, or 240 volts and 480 volts alternating current."" From this it may be inferred that no guards are required, for 250-volt trolley wires, and the natural conclusion to be drawn is that the lack of guards or shields must be held responsible for these fatalities. To prevent fatalities from this source, it has been advocated that every foot of trolley wire in mines should be guarded. While some such drastic step may appear to be amply justified, a closer examination of the records shows that lack of guards is not entirely responsible but rather that carelessness and neglect in the observance of certain well-established simple rules concerning installation and location of trolley wires must also bear a share in the responsibility. In -other words, if trolley wire is installed carelessly and its maintenance neglected, failure may be expected of any guards that have been put up.There are a-number of factors affecting safety as related to trolley wires in mines, among which the following may be enumerated.1. Installation relative to track and passageways.2. Guarding.3. Maintenance.4. Discipline.Acknowledgment is made to D. Harrington and K. L. Marshall of the safety division of the bureau for assistance given in securing data on cost of installing guards for trolley wires.The statement that fatalities should not be charged in every case to lack of guards is supported by the following example: A man operating a locomotive was electrocuted when the trolley wheel jumped the 250-volt trolley wire and allowed it to sag against his shoulder. He was sitting in the regular place provided in the locomotive, but the wire was 11 inches inside of the rail and only 39 inches above it where the wire touched him, or 11 inches from the roof at a distance of 12 feet from the nearest hanger. The accident occurred between two hangers 44 feet apart, and the trolley wire was inside the rail over the entire distance, being 2 inches inside at one hanger and 10 inches inside at the other hanger. A bolt in the roof indicated that there had been a hanger at one time between the two on the 44-foot span.This example is a violation of good practice in the installation and maintenance of trolley wire. In the first place the wire should have been outside instead of inside the rail. In the second place there should have been at least one intermediate hanger so that the span would not be so great and the sag would be reduced. Furthermore, it is possible that the wire was not taut enough even when the intermediate hanger was in place.To provide a degree of safety for men in the mines certain coal-mining States, recognizing the need, have enacted laws to regulate the installation of trolley wires. These limit the distance that the wire must be kept outside and above the rail. Thus, the 1927 mining laws of Ohio specify that:"

Apr 1, 1932

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

To expediate the transfer of technology from Bureau laboratories into new products and processes that enhance the economic competitiveness of the U.S. mining and minerals industry in world markets. Background The U.S. Bureau of Mines and various members of the industry are concerned about the current technology challenge to the minerals industry in the United States. They arc working together to delineate ways of enhancing the mineral industry&apos;s technology base. More emphasis is being placed on collaboration between the government, academia, and industry to formulate the innovative revolutions needed to maintain our technology edge. Through these partnerships, real issues and problems can be identified, the industry&apos;s needs as customers can be defined, and research and development activities can be tailored to meet these needs. Now is an especially exciting time in research because some special opportunities exist to encourage private industry to capitalize on Federal laboratory research and development. These opportunities arc called CRADA&apos;s. What Is A CRADA? The Congress recently enacted a mechanism that enhances collaboration between industry and government through the Technology Transfer Act of 1986. A key lea lure of this Act is a provision through which Cooperative Research and Development Agreements or CRADA&apos;s can be developed to encourage industry and government to work together and stretch their research budgets. By entering into a CRADA, a private, non-Federal company can cost-effectively perform research by sharing the costs of this research with the Federal Government. The agree¬ment involves no transfer of funds from the Government. The Government agrees to provide personnel, services, facilities, equipment or other resources (but nut funds) and the non-Federal party agrees to provide funds, personnel, services, facilities, equipment, or other resources needed to conduct a specific research or development effort.

Jan 1, 1992

By Robert P. Vinson

The U.S. Bureau of Mines evaluated a light-scattering technique for discriminating between spherical and nonspherical particles. This evaluation was a three-step procedure. The first step required collecting light-scattering data for a variety of particles. This was accomplished with a particle analyzer called the DAWN-A. The DAWN-A measured the scattered light intensities of individual particles at a forward scattering angle of 40°. These DAWN-A measurements of individual particles are called scattering signatures by the Bureau researchers. The second step in this evaluation was to calculate a sphericity index number using the scattering signatures produced by the DAWN-A. The sphericity index number can range from 0 to 1. A calculated sphericity index of 1 would show that based on the intensity of scattered light, the particle was a perfect sphere. The third and final step of this evaluation was the comparison of the calculated sphericity indices of the various particles. Comparing these indices made it possible to discriminate between the nearly spherical waterdrops and the nonspherical coal and rock dust particles.

Jan 1, 1993

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-&apos; DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By U. E. Brown

This papery describing the mining methods employed by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the United States. The Bunker Hill and Sullivan mines are situated in the western part of the Coeur d&apos;Alene district at Kellogg, Shoshone County, Idaho. The mines were discovered during the summer of 1885 and except for two short periods of labor trouble, between 1890 and 1900, have been in continuous operation. About 575 men are employed at the mine. The production is about 1,400 tons of lead-silver ore per day. This is treated in the company&apos;s concentrator and smelter at Kellogg.

Jan 1, 1931

By Thomas C. Miller, Rudolph Sporcic

A relatively simple and inexpensive encapsulated hydraulic device has been developed by the Bureau of Mines to facilitate study of coal bumps , and to measure pressure changes in a coalbed as it is subjected to roof loading during mining . Construction of the device and application techniques are described . Preliminary feasibility tests in the laboratory and field indicate that the device responds satisfactorily to pressure changes in coal created by roof loading .

Jan 1, 1964

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960