Search Documents

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

By Frank E. Cash

Large quantities of explosives are consumed in the underground mining of ores in the Lake Superior district. Because of the recognized danger of accidentally releasing the potential highly destructive forces contained, the safes possible procedure in the transportation, storage, and use of explosives is necessary. Underground magazines recently constructed in the district give evidence of the earnest desire of the mine operators to incorporate all possible safe-guards in the storage of explosives, including a careful choice of location and arrangement in the plan of the magazine.

Jan 1, 1946

By K. J. Liles

To encourage the development and conservation of the Nation's ceramic raw materials, the Bureau of Mines, U.S. Department of the Interior, under an agreement with the Georgia Department of Natural Resources, evaluated samples from a clay resource located in Clay County, Ga., for use as a raw material for lightweight aggregate. The physical properties of clay samples, taken from 5-foot increments of drill cores from 11 holes, were determined. Raw materials were plasticized and extruded to produce 1/2-inch by 1-inch pieces and fired in a rotary kiln to produce lightweight aggregate samples. The resulting expanded material had excellent loose pour weights ranging from 30 to 37 lb/cu ft. The expanded test materials were crushed, sized, and used as aggregate to form concrete cylinders. The unit weight and compressive strength of the cylinders averaged 106 lb/cu ft and 3,350 lb/sq in, respectively; these values meet American Society for Testing and Materials specifications for structural concrete. The clay from the drill cores was also used to make test bars that were evaluated for building brick.

Jan 1, 1980

Provide a strategy for calculating optimum distribution of selected sensors for detecting underground mine fires. Approach The Bureau of Mines performed research to determine adequate distribution of product-of-combustion (POC) fire sensors within mine entries. This placement strategy would improve the miner's chances for escape by locating sensors where they would most effectively, quickly, and efficiently detect fires resulting from coal or wood combustion. Spacing of Sensors Placement strategy guidelines were based on the performance of 160 F heat sensors with ideal operating characteristics which were placed at intervals of ten feet in underground mine entries. Data obtained from full-scale mine fires were used to estimate fire sizes and alarm activation times for the heat sensors. Various equations were then developed to determine spacing requirements for any fire detection system installed in entries of varying heights, widths, and ventilation rates.

Jan 1, 1983

By Maria I. De Rosa

The major fire and fire injury findings for all coal mining categories for 1990-1999 are reported in tables 37-38. Table 39 and figure 13 show the number of fires. fire injuries, risk rates, employees' working hours, and coal production (under- ground and surface coal mines only) by time period for all coal mining categories. Table 40 shows major findings (for under- ground coal mines only) for 1978-1992. For all coal mining categories, 458 fires occurred during 1990- 1999; 157 of those fires caused 164 injuries and 2 fatalities (Ewhr = 2,070 x l0%r, Irr = 0.016: C'P (for underground and surface coal mimes only) - 10,363 x l0\t, Frr = 0.044, LWD = 14,753). Twenty-nine fires and 17 injuries involved contractors. Sixty-six fires required firefighting interventions by mine rescue teams (25 times in underground mines) and fire brigades and fire departments (at least 41 times at surface coal operations). In all, 51 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 114 fires were detected late, and 42 fires were undetected. The greatest number of fires and fire injuries occurred at surface coal mines; the highest risk rate values were also calculated for this category. For all coal operations, the ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flames (1 03 fires or 23% with 69 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (98 fires or 2 1 % with 29 injuries), spontaneous combustion/hot coal (62 fires or 14%), electrical short/arcing (49 fires or 11% with 18 injuries), and conveyor belt friction (3 1 fires or 7% with 6 injuries).

Jan 1, 2004

By J. W. Town

The Bureau of Mines studied the effects of reducing gas composition, tem-perature, and superficial gas velocity on the regeneration rate of alkalized alumina. Regeneration was assumed to follow the simple first order reaction for removal of sorbed S02: dµ/dt = -Kµ. An Arrhenius relationship can be plotted, which shows an activation energy of about 75 kcal/mole for simulated reformed propane. The general effects of the individual gases can be described as follows: (1) CO and H2 produced rates proportional to their con-centrations, up to about 5 percent for each; (2) addition of CO2 had no effects on the regeneration rate by CO; (3) the regeneration rate by H2 was lowered by the addition of H2O while the regeneration rate by CO was increased by 0 addition; (4) H2S showed a positive effect up to concentration levels of about 2 percent and then produced a rapid negative effect; (5) carbonyl sulfate (COS) increased the sulfur content; and (6) propane was as effective in regenerating the loaded pellets as was simulated reformed propane.

Jan 1, 1971

By Larry J. Nicks

The Bureau of Mines is investigating the catalytic activity of rare-earth compounds to develop a catalyst for the cathode reaction of a hydrogen-oxygen fuel cell. This report presents the results of studies of the catalytic activities of lanthanide oxides for the oxidation of hydrogen at 150° to 250° C. Preliminary activity tests were made with approximately stoichiometric mixtures of hydrogen and oxygen diluted with helium. A series of tests was also run under oxygen-rich conditions in which specific rate constants and activation energies were determined. Variations in rate constants up to 2,000 times were observed for the various lanthanide oxides. The three most active catalysts were oxides of Ce, Pr, and Eu, having specific activities of 6.93 X 10-7, 4.88 X 10-7, and 4.06 X 10-7 moles H2.sec-1.m-2, respectively, at 200° C.

Jan 1, 1973

By T. E. Green

The Bureau of Mines Heavy Metals Program emphasizes the need for improved analytical methods for gold determination. A commercially available ion exchange resin with high selectivity for gold was investigated as a potential method to collect gold from solution. The resin was found to quantitatively collect gold from acid solutions over a wide range of acid concentrations. Common metals were not collected by the resin nor did they seriously interfere with the collection of gold. X-ray spectrographic and neutron activation methods based on the use of papers containing this resin are proposed.

Jan 1, 1970

By Alan H. Goode

The advancement of high-temperature drilling fluid technology for application in geothermal environments is part of the Bureau of Mines program for more efficient development of our Nation's energy resources. The bentonite constituent of water-base drilling fluids is sensitive to destabilization by high-temperature and salinity. A substitute material for bentonite, phosphate slime, which is reported to be saline resistant, was considered. These studies show that spray-dried slime suspensions have more favorable rheological behavior, but poorer filtration properties, as compared with bentonite suspensions.

Jan 1, 1975

By H. B. Cooke

In connection with its researches on the crude petroleums of the United States, the Bureau of Mines has made a particular study of apparatus for the distillation of hydrocarbon mixtures. While this study is still incomplete it has already resulted in the development of considerable laboratory and semi-plant equipment, motet of which has been described in various publications of the Bureau. The laboratory apparatus (Hempel distillation) and method gives satisfactory comparative results in the laboratory examination of crudes and have been found applicable to crudes of all types, but the agreement of laboratory and plant distillations is not as close as might be desired. This is due, in part, to limitations in size and construction of the laboratory apparatus. Some refiners claim that the Bureau of Mines' laboratory method (Hempel distillation3) for distilling crude petroleum, does not show the full gasoline content of the oil, while others have stated that it indicates more gasoline than can be obtained from the crude commercially. This difference of opinion among refiners results largely from the great variation in stills used and methods of operating them. The Bureau's experience has shown that crude oils from different fields vary widely in character; in fact, that it is not yet possible to classify crude's adequately on the basis of their Down chemical and physical characteristics. As a result of the differences that exist among crudes, and of the difficulty of designing refinery equipment, no standard practice has yet been adopted for the commercial distillation of petroleum, and ma" types of stills are used in the refineries of this country. Although many factors enter into the design of equipment and the development of commercial practice in refining of crude oil, there

Jan 1, 1924

By Christopher C. Jobes, N. Kumar Kittusamy, Alan G. Mayton, Dean H. Ambrose

Researchers with the National Institute for Occupational Safety and Health (NIOSH) conducted a systematic study to evaluate seat designs on low- and mid-coal-seam shuttle cars. The purpose was to gather additional data to support earlier findings that NIOSH seats, with unique viscoelastic foam padding, are indeed improved designs for coal mine shuttle cars. This study included a larger sample of shuttle car operators than a prior NIOSH investigation. Eight shuttle car operators participated in evaluating seat designs on the basis of perceived levels of vehicle jarring/jolting and discomfort. Researchers then compared the operators’ perceptions with field-measured levels of vehicle jarring/jolting. Seven seat designs were evaluated on low- and mid-coal-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. These seat designs comprised the one already in use on each vehicle and five NIOSH designs. Experimental data were collected using accelerometers, signal conditioning amplifiers, and filters connected to a data recorder, whereas subjective data were gathered via a visual analog scale (VAS) and a questionnaire. Field trials included shuttle cars operating under full- and no-load conditions. VAS responses indicated that NIOSH-designed seats performed better relative to comfort and isolation from vehicle jarring/jolting than the existing seats used in the shuttle cars. Both mid- and low-coal-seam shuttle car operators, during no-load and full-load conditions, rated lower levels of jarring/jolting with the NIOSH seat design. Questionnaire responses indicated that shuttle car operators rated NIOSH seat designs as more comfortable. Vehicle operators most frequently suggested the addition of armrests as a way to improve the seats on the mid-seam shuttle car. The quantitative levels of vehicle jarring/jolting for the no-load condition (more severe condition for vehicle operation) showed that NIOSH seats for the mid-coal-seam shuttle car performed better than the existing seat in terms of peak acceleration and crest factor. Similarly, for the low-coal-seam shuttle car, NIOSH seats performed better than the existing seat in terms of peak acceleration, root-mean-square (RMS) acceleration, and crest factor.

Jan 11, 2006

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By M. L. Davis

The principal causes of many methane-gas explosions that have occurred in anthracite mines, especially in thick pitching veins, during recent years can be traced to lack of a satisfactory method of testing for such gas in areas adjacent to those in which blasting is to be done or other sources of ignition introduced. As coal-mine officials and inspectors are required to make examinations for methane in all accessible open workings, including high places, and permissible flame safety lamps have been used almost universally for making these examinations, considerable difficulty has been experienced in proper testing of atmospheres at elevations beyond the normal reach of the examiner, and resultant explosions have often indicated perfunctory tests. The accepted practice of testing for gas in voids or high places generally consists of raising a flame safety lamp, suspended from the end of a long drill, stick, or pipe, into the atmosphere to be tested. Disadvantages noted are: Action of the flame within the lamp cannot be seen readily when the lamp is more then 18 inches overhead, the flame will not be extinguished when less than about 4-1/2 percent of methane is present, and indications of small percentages of methane within the lamp may disappear entirely while the lamp is being lowered slowly to view; the examiner must usually be exposed unnecessarily to falling material; and the lamp may fall and be broken. Thus, the need for a more reliable, safe method of testing for gas in out-of-reach places is apparent. Several electrical methane detectors, tested and approved by the Bureau of Mines, have been used satisfactorily, though infrequently, for making the aforementioned gas tests. Some of these detectors employ a rubber aspirator bulb and rubber tubing of suitable length to draw the atmosphere from high places through and over energized parts of the detector. However, the original expense, susceptibility to damage, and awkwardness of tarrying these instruments in steep-pitch workings has precluded their general use in everyday examinations. Although not as efficient as the electrical detector for determining small percentages of methane or as reliable because of the limitations imposed by oxygen-deficient atmospheres, the modern per¬missible flame safety lamp can, it is believed, be used safely with the rubber aspirator bulb and tubing to greater advantage and with comparative reliability in testing for gas in out-of-reach places. Slight reference to this method of introducing air into a safety lamp is made in a Bureau of Mines publication of l921,2/ and it is quite possible that the method has been utilized in some manner by individuals in American mines during the intervening years. A similar method was used in connection with a nonpermissible Wolf flame safety lamp in at least one coal mine in Japan before World War II. A major change in the construction of this lamp would bar its approval by the Bureau of Mines. An American adaptation of the Wolf lamp, developed

Jan 1, 1954