Search Documents

Provide a means to (1) rapidly disconnect a multifunctioning signal channel from a multichannel data collection system, (2) protect electronic devices from damage while causing the minimum amount of data collection disruption, and (3) operate electronic devices under gassy mine conditions. Background Data collection system instrumentation and cables are often located in hazardous areas of underground coal mines. As a result, frequent damage to the instrumentation cables occurs from roof falls, heavy equipment, and the relocation of air, water, and power lines. A similar problem exists in surface areas where cables and instrumentation can be damaged by animals and by vehicle traffic. Without a circuit-breaking feature, the damaged cables could cause instrumentation to be ruined, cause power supply failure, and otherwise disrupt data collection in some situations the lack of a circuit-breaking feature might cause an ignition in a methane atmosphere.

Jan 1, 1990

To minimize support costs and to improve ground control by improving wood-crib design and utilization through the development of engineering methods that will match the placement and performance of the wood cribs to the load conditions imposed by the mine environment. Background While wood cribs are used extensively to stabilize mine openings, their utilization is often based on historical practice or trial-and-error rather than on engineering design. This has led to conservative crib utilization where more capacity than is necessary is employed or inadequate capacity is provided when mine conditions worsen. Critical design parameters, such as the stiffness of the support structure, are often ignored. Optimum crib design and employment is becoming increasingly important as the utilization of wood cribs increase due to the growth of longwall mining, and as the cost of wood continues to rise. A single longwall operation will spend as much as a million dollars per year on the support of the gate roads.

Jan 1, 1994

By Robert L. Chufo

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of "seeing into the earth." A first generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full threedimensional (3-D) imaging system that will have applications in both the underground and surface environment.

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By Kathleen M. Kowalski-Trakofler

This paper discusses human judgment and decision making under stress. The authors review selected recent literature across various disciplines and suggest a definition of stress within the context of decision making during the management of emergencies. They also discuss fieldwork by the Pittsburgh Research Laboratory, NIOSH, which explores traumatic incident stress, the relationship between previous training and performance under stressful conditions, and human behaviour in underground mine fires. The authors assert that stress is one of the factors that decision makers must contend with in most life-or-death situations. They suggest that a better understanding of individual judgment and decision making activities whilst under stress would yield a better understanding of how people reach the choices they make in emergencies. This enhanced understanding would be of enormous value to emergency managers, researchers and policymakers.

Jan 1, 2003

By R. T. Johansen

The wettability of petroleum reservoir materials by water and crude oil has been recognized as an important factor in determining waterflood behavior. The problem of simulating and studying reservoir conditions and characteristics, to produce laboratory results congruous with field experience, has been examined by many methods. (1, 2, 3, 4).4/ The most generally accepted approach to this problem is determining wettability of the porous medium by imbibition methods; or, after solvent extraction, predetermining the wettability of the samples by coating the surface of the medium to render it preferentially oil-or water-wet (3, 5). The emphasis of wettability studies has been placed on the characteristics of the reservoir materials with little consideration being given to the fluids themselves. Therefore, the wetting tendencies of crude oils have been investigated by a recently developed method (6). Imbibition and the more general phenomena of capillary pressure are the most direct ways to measure wettability. The simplest type of capillary pressure observations involves the use of an interfacial-tension capillarimeter, which does not produce as separate values either interfacial tension or contact angle. Actually, these quantities do not have independent significance in reservoir engineering, and the property of wettability they are intended to evaluate is given, immediately by capillarimetric measurements.

Jan 1, 1961

By Richard F. Hewlett

An attempt has been made to fit assay data from an underground copper deposit to a three-dimensional polynomial surface as a means of expressing assay points in terms of their mine coordinates by a mathematical equation. The resulting equation was evaluated to predict the grade trend of the deposit. Although the fit obtained by this initial experiment is not considered accurate enough to provide good predictions about the deposit, the methodology is presented in this preliminary report to show the potential usefulness of the technique in mineral deposit evaluation. The technique also should be useful in determining the grade of blocks of ore for production scheduling and blending problems in open pit operations. Further experimentation is needed to increase the reliability of the computer program, to increase the precision of the method, and to make the solution more flexible for use on other mineral deposits.

Jan 1, 1964

By D. Harrington

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protecting exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

Jun 1, 1921

By D. J. Parker

The oft-repeated expression that the taproot of safety lies in the attitude of the management toward accident-prevention work is indisputable and has become almost an axiom. Trite and somewhat timeworn though the statement may be, it is nevertheless true that the supervisory force must earnestly support a policy of safety and maintain at all times a con¬ siderate regard for the welfare of the employee if that high degree of cooperation of the employee, so vital to the successful prosecution of any safety program, is to be expected. The responsibility for preventing accidents rests upon the management, and in the case of the Spring Canyon Coal Co. such responsibility is recognized and accepted with little or no reservation. This company, aside from the humanitarian aspects involved, believes that safety is good business and not a matter to be treated passively or in a perfunctory manner. The problems with respect to safety that have been met and wholly or partly solved can best be appreciated when some of the natural conditions, adverse and otherwise, existing at this operation are taken into consideration. Mine 1 is about 1 mile north of the town of Spring Canyon, Carbon County, Utah, and is served by both the Denver & Rio Grande Western and Utah Coal Route railways. During the year 1931 the mine produced 312,397 tons, approximately 10 per cent being derived from pillar workings. The normal daily output during the summer months is about 2,000 tons, and during the peak of production in the winter season the daily production varies from 2,500 to 3,000 tons. The number of miners varies from 87 in summer to 220 in winter, and the day men vary in number from 66 in the winter to 45 in the summer; 12 company men are employed the year around. The officers of the company are J. B. Smith, president, San Francisco, California; T. R. Stockett, general manager, Salt Lake City; and G. A. Murphy, superintendent, David Brown, assistant superintendent, and John Sullivan, mine foreman, all of Spring Canyon, Utah.

Dec 1, 1932

By Jeffrey M. Listak, Gregory J. Chekan

The U. S. Bureau of Mines is investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When coalbeds are longwall mined in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model, a boundary element computer program, was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. ALPS provided a basis to verify model trends and to recommend limits for safe pillar design when superpositioning longwall gate roads. The attributes of the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam factor (MS) to estimate the stress on superpositioned lower mine gate road pillars. Numerical analysis shows that MS depends on the interburden thickness and pillar width.

Jan 1, 1992

By M. B. Cooke

 An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study now in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith and Cooke, which involved evaporation of e semple of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the steam bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is ex- cluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

May 1, 1925

By Foster Fraas

In the separation of a component from a mixture , two fractions are obtained , one containing a high - percentage composition of the component and the other a low - percentage composition . The high - percentage fraction is frequently called the concentrate and the low - percentage fraction the tailing . In many separation processes the recovery is not complete , and the composition of the concentrate decreases as the recovery of the component, which is concentrated , increases . It is this particular class of separations to which this paper is confined .

Oct 1, 1942

By Eric Zahl, John Dunford, Hamid Maleki

Coal bumps are defined as sudden failures of rock and coal near entries that are of such a magnitude that they expel large amounts of material into a mine opening. Coal bumps are influenced by geologic conditions, the geometric design of coal mine excavations, and the sequence and rate of extraction. Researchers from private industry and the National Institute for Occupational Safety and Health have studied mechanisms of violent failure and have identified individual factors that contribute to coal bumps. In an attempt to develop tools for assessing coal bump potential, the authors initiated a comprehensive study using information from 25 case studies undertaken in U.S. mines. Multiple linear regression and numerical modeling analyses were used to identify the most significant variables contributing to coal bumps (excluding bumps related to fault-slip). Twenty-five geological, geometrical, and geomechanical variables were considered initially. The most important of these variables were then identified as (1) energy as calculated using the mechanical properties of the strata, depth of overburden, and joint density, (2) mining method, (3) pillar factor of safety, and (4) stress gradient and yield characteristics.

By R. P. Vinson, D. P. Tuchman

The personal dust monitor (PDM) is a sampling device developed for measuring the personal exposure to coal mine dust of mine workers. The device is based on proprietary technology known as the tapered element oscillating microbalance (TEOM) originally developed as a fixed- site environmental particulate mass monitor by Rupprecht and Patashnick Co., Inc., Albany, NY. Currently, the monitoring of exposure to coal mine dust relies on periodic samples taken by traditional coal mine dust sampling units that use a cyclone, filter, pump, and laboratory measurement of the filter mass. Better measurement of mine dust levels has been the goal of industry and labor for nearly two decades. PDM technology offers accurate, end-of-shift and near real time assessment of worker dust exposure. Laboratory and underground tests compared measurements taken by a prototype PDM-2 (a two-piece TEOM) to the average of multiple personal dust samplers monitoring the same space. In the range of mass loadings P between 0.5 and 4.0 mg/m the PDM met a 25% accuracy criterion 95% of the time with 95% confidence. However, some questions still exist about potential bias between types of coal. The prototype two-piece device is in the process of being combined into a single unit that also contains the miners' cap lamp creating a more ergonomic dust sampling system.

By L. C. IlsLey

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators2 of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jun 1, 1927

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By D. J. Bauer, V. E. Shaw

Bastnasite concentrate was processed to recover total rare - earth content and obtain high - purity ceric nitrate . Reaction of the concentrate with 45 percent caustic soda for 1 hour at 180 ° C in stainless steel vessels resulted in 99 - percent conversion to rare - earth hydroxides . A drying step followed by solution in nitric acid produced a tetravalent cerium fraction amenable to extraction with TBP . Single- stage separatory funnel experiments resulted in 90 -percent recovery of ceric nitrate at a purity of 99.9 percent . Fractional extraction in pressure - bubbler columns resulted in 98.5 - percent recovery of 99.5 -percent - pure ceric nitrate .

Jan 1, 1964

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By Clarence Hall, Charles E. Munroe

In accidents resulting from the use of explosives in metal mines and quarries in the United States more than 130 men were killed and 250 seriously injured during the calendar year 1913. More- over, an unknown number of miners suffered from the effects of breathing the harmful fumes and gases given off by the burning or the incomplete explosion of some explosive. Consequently, the Fed- eral Bureau of Mines, which is endeavoring to increase safety in mines and to abolish conditions that tend to impair the health of miners, is studying the kinds of explosives used in mining and the conditions under which these explosives can be used with least danger to the miner. Information about the different explosives used in coal mining and the precautions to be taken in using those explosives has been printed in Bulletin 17 and other bureau reports, the names of which may be found at the end of this bulletin. The bureau has not been able to give much attention to explosives used in metal mines and quarries, but has published some information about these explosives in Bulletin 48, "The Selection of Explosives Used in Engineering and Mining Operations"; Technical Paper 17, "The Effect of Stemming on the Efficiency of Explosives"; and Miners' Circular 19, "The Prevention of Accidents from Explosives in Metal Mining." This bulletin aims to give the metal miner and the quarryman information similar to that given the coal miner in Bulletin 17. In- flammable gas or dust is seldom, if ever, found in quarries or metal mines, and the danger from using explosives there is less than in coal mines; but, as the figures show, the number of men killed and injured yearly in accidents caused by explosives proves the need of both miners and mine officials striving to see that none but proper explosives are used and that these are used properly.

Jan 1, 1915