Search Documents

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

By Robert A. Jankowski

The U.S. Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the mining industry, has identified and demonstrated the effectiveness of several improved face ventilation techniques for longwall mining systems. These include the following: identifying improved techniques for measuring face ventilation parameters on longwall sections, installing curtains at the intake end of the longwall face to maximize usage of the primary airflow, identifying optimum face airflow rates for maximizing dilution effects, and coursing the primary face intake from tailgate to headgate to minimize outby airflow contamination. Application of these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1993

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

By R. W. Nash

This report describes the design and operation of a digital instrumentation package for the Bureau of Mines improved torsion pendulum, a scientific instrument that measures the vibration damping of metallic materials. The new design eliminates manual analog-to-digital conversion, reduces the data acquisition time, and increases the precision of the measurements. The digital output can be coupled directly to a micro-processor or computer to produce the final data in real time.

Jan 1, 1983

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By C. E. Saxon, F. E. Cash

"Adequate lighting for all mining operations would unquestionably tend to promote both safety and efficiency; this would be true not only for men but also for the animals that man impresses into service in mines. The Markeeta Coal Co. and the Alabama Fuel & Iron Co. both operating mines in Alabama, have found that equipping mine mules with portable electric lights is more efficient, much more humane, and far more safe for both men and animals then the more or less usual method of forcing the animal to do its work essentially in darkness.This report is intended to give the mining industry data, that will aid in trying to bring about safe and efficient operation of mines.The authors desire to thank Charles F. DeBardeleben, president, Fred R. Bell, general manager, Hewett Smith, C. H. Shepherd, and R. A. Sensing, superintendents for the Alabama Fuel & Iron Co.; and Charles F. DeBardeleben, Jr., president, and H. M. House, superintendent for the Markeeta Coal Co., for their cooperation in furnishing the data for this paper.The eight mines operated by the Alabama Fuel & Iron Co. and one operated by the Markeeta Coal Co. in Jefferson and St. Clair Counties, Ala., are the only mines in Alabama where mules are provided with portable electric lights, and there are few if any mines in other States in which this system is in use.These two companies are convinced that equipping all mine mules with good lights decreases underground haulage cost by animals by prolonging the useful life of the animals, increasing their efficiency, lessening haulage wrecks and delays on haulage, and increasing production. Last but not least of the advantages would be the more humane treatment of the animals.The nine mines are developed by slopes along the dip of the coal bed, with double-room entries on 200- to 300-foot centers turned right and left off the slopes and with approximately 1 per cent grade in favor of the loads. Rooms are driven up or diagonally up the pitch from these entries.A surface hoist delivers the empties from the surface to the entry sidetracks at the slope and pulls the loads to the surface. From these sidetracks, mules pull one to four wooden cars, each of which holds 1-1/2 to 2-1/2 tons of coal, deliver the empties to the rooms and entry faces, and pull the loads to the slope sidetracks. The mule haul varies from 100 to 3,000 feet; there are no locomotives or trolley wires in any of these nine mines, seven of which are rated as gassy and two as nongassy by the Alabama state Mining Department."

May 1, 1933

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

By Larry Patts, Michael J. Brnich

Approximately 45% of U.S. coal is produced from underground mining. The use of diesel engines to power under- ground mining equipment has steadily increased over the past four decades in an effort to improve mine safety and productivity. Several advantages realized with the use of diesel-powered mining equipment in underground coal mines are listed in Table I. The primary disadvantage of using diesel equipment in underground coal mines is that diesel exhaust emissions can contaminate mine ventilation air. The major constituents of diesel exhaust are gaseous emissions (which include carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons) and diesel particulate matter (DPM). The Mine Safety and Health Administration (MSHA) has incorporated threshold limit values for all gaseous components of diesel exhaust into their regulations. These have been established by the American Conference of Governmental Industrial Hygienists.

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952

By R. V. Ramani, V. T. Burgos, J. A. McClay

Summary Cost models have, long been confined to the accumulation and analysis of static-data.. While historical and time study data are valuable for control of existing operations, for new systems and equipment, and for projections, they need to be adjusted or modified. The availability of computer-oriented systems simulators provide yet another method for costing these systems and equipment. This investigation has introduced a concept whereby continuous, variable data can be assimilated and analyzed through the combination of an economic analysis model, which includes a direct costing capability, with a systems simulator. This tandem operation permits increased flexibility and greater atten¬tion to detail in the evaluation of mining systems. The direct costing process is carried throughout the majority of the model operations. Labor and capital costs may be computed directly, even in the absence of the systems simulator, while operating costs re¬quire input parameters, at present, from the subsystems of the Master Design Simulator. Since the costs computed are based on the perfor¬mance of each individual machine unit, the model may be used to evaluate equipment compatibility, system interaction at the mining face, and the effect of system elements on total mining costs. Additional applications of the cost model include the following: 1. Complete mining systems may be evaluated, over their economic life, to determine the feasibility of a profitable operation. 2. Costs associated with mining various segments of the coal deposit may be computed as a guide to planning the mine layout and scheduling the sequence of operations or acquisition of new

Jan 1, 1975

By John T. Aydelotte, Martin J. Gavin

" Oil shale contains little or no oil as such , but it contains an organic material from which oil may be produced by destructive distillation" . This statement , or others conveying the same meaning, appears in many popular and techni cal articles on oil shale . It is based on the belief that the ordinary solvents of petroleum have but little action on the organic substances contained in oil- yielding shales , although on distillation these same shales may yield upwards of 50 gallons of crude shale oil per ton . A 50 - gallon shale thus yields by distillation 18.73 per cent of its weight as oil ( assuming the specific gravity of the oil to be 0.900 ) , although only a relatively small part of this can be recovered by extraction with such solvents as chloroform , carbon tetrachloride , and the like . In the course of certain experiments designed to determine the solubilities of different shales after they had begun to yield oil by distillation , it was found desirable to determine the quantity dissolved from certain unheated shales by various solvents , at or near the boiling points of these solvents . The method used and results obtained are presented below. These experiments were made in connection with the oil - shale investigations being conducted by the U. S. Bureau of Mines , in cooperation with the States of Colorado and Utah .

Jan 1, 1922

By Carlton E. Brown, William P. Yant

"INTRODUCTION Direct visual microscopic determination of particle-size distribution and number concentration of atmospheric dust is time-consuming and trying to the eyes. By using the microscope to project images of the particles at high magnification onto a screen much of the eyestrain can be eliminated and particle-size distribution results obtained with less effort and at a considerable saving in time. It also permits simultaneous observation of the images by more than one person. Microprojection requires no more skill and very little more apparatus than is required in the use of the microscope. Anyone familiar with the microscope should be able to obtain as perfect images on the projection screen as in direct visual microscopy since the same laws and limitationsThe theory and practice of microprojection are described in detail in texts. 5/6/ The procedure has been used and found to be satisfactory for measuring the particle-size distribution of sub-sieve-size substances, such as pigments and powder 7/8/ in the same size range as that of atmospheric dust. The Bureau of Mines has used the microprojector and found it to be quite satisfactory for (1) the determination of the number concentration of atmospheric dust R.I. 3289 in samples collected by the Owens jet dust counter; (2) particle-size distribution in samples of atmospheric dust collected by the Owens jet dust counter and by the electric precipitator; and (3) the particle-size distribution of dusts, blood cells, bacteria, and pollen. Work is in progress at this Bureau on the use of the microprojector in counting impinger samples. The use of different kinds of illumination, such as reflected (dark field), polarized, monochromatic, and ultraviolet, in the projection of images of atmospheric dust particles is being considered."

Oct 1, 1935

By N. S. Dalal, X. Shi

"The oxidation of NADPH by vanadate(V) in the presence of glutathione reductase showed typical enzymatic kinetics. The oxidation was inhibited by N-ethylmaleimide, a glutathione reductase inhibitor. Superoxide dismutase had no significant effect on the oxidation, indicating non-involvment of the superoxide radical. The vanadate(V) reduction was found to be a one-electron transfer process. These results suggest a new pathway for vanadate(V) metabolism and a new function of glutathione reductase. Compounds of vanadium(V), such as NaV03 , exert potent toxic effects on a wide variety of biological systems (1-3). Despite intense current activity, however, the biochemical mechanism of vanadate(V) toxicity is still not well understood (1- 14). It is believed that one of the important pathways involves the oxidation (by vanadate(V)) of NAD(P)H (15, 16), but, to our knowledge, there has been no report of the identification of any vanadate(V) reductase. With a view to finding if there exists any vanadate(V) reductase, we have investigated the oxidation of NADPH by vanadate(V) in the presence of glutathione reductase. Glutathione reductase (GSSG-R)2 was selected because our previous studies have shown (17) that GSSG-R can act as a reductase for chromate(VI), which is isoelectronic with vanadate(V). We find that GSSG-R does indeed function as a NADPH-dependent vanadate(V) reductase, thus pointing to a new pathway for the metabolism of vanadate(V), as well as to this property for GSSG-R. MATERIALS AND METHODSSodium metavanadate (NaV03 ), henceforth vanadate, was purchased from Aldrich and its solution was always freshly prepared. The GSSG·R used was from bovine intestinal mucosa and was purchased from Sigma. The oxidation of NADPH was followed photometrically as the decrease in absorbance at 340 nm. The spin trap, 5,5-dimethyl- pyrroline-N-oxide (DMPO), was purchased from Aldrich and used without further purification, since very weak or no spin adduct signal was obtained from the purchased sample when used alone.ESR spectra were obtained at X-band (9.7 GHz) using a Bruker ER200 ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR gaussmeter (Bruker, Model ER035A) and the microwave frequency was measured with a digital frequency counter (Hewlett-Packard, Model 5340A). An ASPECT 2000 computer was used for data storage and analysis. The concentrations given in the figure legends are the final concentrations. All experiments were carried out in the phosphate buffer solution (pH 7.2) and at room temperature."

Jan 1, 1990

By Jon K. Ahlness

The Bureau of Mines, in cooperation with the Institute of Mineral Research of Michigan Technological University, and the Upper Great Lakes Regional Commission, conducted an investigation of electronic sorting of native copper ore from Upper Michigan. This report is based on research by the Institute of Mineral Research under contract to the Bureau. The test program evaluated the use of belt and rotary sorters on various size and grade fractions of ore. Both plant-scale sorting and lab sorting tests were run. The plant sorting objectives were to determine the sortability of different ores and the efficiency of the electronic ore sorters. High-and low-grade ores from both conglomerate and amygdaloid types were separated into four size fractions. The two larger sizes were sorted on belt sorters and the two smaller ones on rotary sorters. Copper recoveries ranged from 20.0 pct from a feed grade of 0.40 pct to 80.3 pct from a feed grade of 1.08 pct. Lab sorting tests of conglomerate ore were run to determine the efficiency of a belt sorter equipped with a second sensing coil located above the belt and to determine the sorting characteristics of larger ore size fractions than those used in the plant sorting. Copper recoveries from the combined feed sizes ranged from 47.0 pct from a feed grade of 0.13 pct to 96.8 pct from a feed grade of 4.87 pct. For all the ore types except one, it was found that the copper recovery increased with the feed size.

Jan 1, 1980

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

By W. W. Adams, E. E. Getzin, T. D. Lawrence

"The thirteenth annual accident-prevention competition conducted by the Bureau of Mines during the calendar year 1937 was completed with 318 mines and quarries participating. This contest, known as the National Safety Competition, is open to all minas and, quarries employing 25 or more men underground or in the quarry or open pit. The entries are divided into five groups to obtain as nearly as possible uniformity of operating conditions and hazards. The five divisions are: (1) Underground anthracite mines, (2) underground bituminous-coal mines, (3) underground metal mines, (4) underground nonmetal mines, (5) quarries and open-pit mines. A bronze trophy, known as Sentinels of Safety, provided by the Explosives Engineer magazine, is awarded to the winner of each group. The trophy is kept by the winning company 1 year and then transferred to the winner of the succeeding year's contest. Certificates of Honorable Mention are given to plants ranking second, third, fourth, and fifth in each group and to all plants operating without a lost-time accident provided the period of exposure to hazard was not less than 30,000 man-hours. Relative standing in the contest is determined by the contestant's accident-severity rate, which represents the total number of days of employee disability from accidents per thousand man-hours worked by all employees.The 1937 contest was outstanding in that the accident-frequency rate for the contest group as a, whole was the lowest on record. Moreover, with one exception 1934, the accident-severity rate was the lowest ever attained: For frequency, 3S.0 accidents per million man-hours worked; and for severity, 8.2 days lost from accidents per thousand man-hours worked. The rates represent a decline of 62 percent in accident frequency since 1925, the first year of the contest, a remarkable accomplishment both for the contest group and for the purpose of the contest because a majority of the contestants have not only participated during the past year but have been enrolled several years, some enrollments even dating back to 1925."

Aug 1, 1938