Search Documents

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By Fred C. Turin, Sean Gallagher, Kim M. Cornelius, William J. Wiehagen

An important part of initiating a site-wide ergonomics evaluation process is prioritizing jobs to be analyzed. While injury data is important, other factors such as worker discomfort and physical exertion requirements, should be considered. This paper describes the use of four sources of data (injury records, the Nordic Standardized Musculoskeletal Questionnaire, supervisor interviews, and management concerns) to prioritize jobs for ergonomic analysis. The approach described integrates the four sources using a decision matrix to prioritize jobs for ergonomics analysis.

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By Kenneth P. Klouse

The current rulemaking on mine illumination makes it necessary for mine personnel to have an understanding of the behavior of light. They must be able to understand many terms that are new to the industry and must be familiar with the use of various types of photometers. With this knowledge, the enforcement criteria for mines can be understood and compliance can be maintained.

Jan 1, 1976

By Dara Stock, Fred Turin, Kim Cornelius, Lisa Steiner

Growing concern from labor unions, regulatory agencies, and industry about the safety of a prevalent underground coal mining method which utilizes remote control has prompted human factors field evaluation of mining activities. Remote control operations were implemented with little consideration given to human-system interactions. Ideally, collecting and analyzing information prior to implementing new technology would have helped to address potential problems. One such problem that operators and other mine personnel are faced with is the question of where they should safely position themselves to avoid injury while remotely operating machinery. To determine work methods employed by machine operators before and after implementation of the new method, work sampling techniques have been used to provide data about positioning of face crew members at different points in the mining cycle. This data provides information for optimal positioning, leading to safer operating procedures and identifying training shortfalls.

By Thomas J. Peters

The U.S. Bureau of Mines studied the 3,500-acre Winegar Hole study area, Idaho, a legislatively proposed (101st U.s. Congress) addition to the Winegar Hole Wilderness, Wyo.; it adjoins the western boundary of the Wilderness at the Idaho-Wyoming border, about 15 m; east of Ashton, Idaho. The study was part of an Idaho Land Assessment Program to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The study area is an east-west elongated, wooded plateau south of Falls River. Although the area is covered with surficial glacial deposits, it is probably underlain by volcanic flows; light-colored and mafic flow rock were noted in sparse outcrop. No mines, prospects, mineralized areas, or mineral resources were found in the study area during a literature and field search. The only nearby prospects include geothermal and rock aggregate (volcanic cinder) sites, and several placer claims. Although the Winegar Hole study area lies within a region of potential geothermal resources, no evidence of geothermal activity was observed. Rock in the area does not split into flat slabs, which could be useful as dimension stone, and would require crushing to be used 8S aggregate. Alluvium (placer) samples contain less than SO.01 per cubic yard gold (at a $350 per oz price); alluvial deposits are too small to contain gold resources.

Jan 1, 1992

By Miller, ALEX U, Edward Thomas

In March 1937 the entire country was shocked by news of an explosion of gas in a New London (Tex.) schoolhouse, which resulted in the death of 280 pupils and 14 t eachers. The Government investigators of this disaster believed that the cause was the ignition and explosion of a large volume of explosive natural gas-air mixture that had accumulated in a poorly ventilated space beneath the first floor of the main school building and that this accumulation was due to leakage from gas lin suspended underneath the floor to carry the gas supply to the school.!i/ For some years there has been a potential explosion hazard in school houses and other buildings that are supplied with water from deep wells in certain parts of Illinois. Notwi thstand.ing the disaster at New London, Tex., and the fact that there had been gas ignitions at four water wells in different parts of the State, the explosion hazard in schools and other buildings was not fully recognized until a few months after the disaster in Texas, when an explosion occurred in the settling basin of the municipal water works of Clinton, Ill., and another in a pump house of the municipal water works in Normal, Ill, The explosion in the settling tank of the municipal water works in Clinton, Ill., occurred on August 12, 1937, and a.id considerable damage to the settling tank, but fortunately no one was injured. At the time of this explosion rapairs'and aJ.terations to the water plant were in progress, and 10 men were employed in the immediate vicinity of the settling tank. Two of these men were enlarging a hole in the concrete side with an air hammer for the installation of a larger discharge line.

Aug 1, 1938

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for surface sand and gravel mines by state during 1990-2001. Table 28 also shows the injury risk rates, employees' working hours, and lost workdays. At surface sand and gravel mines, a total of 70 fires with 60 injuries occurred in 29 states during 1990-2001. Fifty-nine of the fires caused 60 injuries (none of the fires involved contractors). The yearly average was 5.8 fires and five injuries. The Ewhr value was 741 x 106 hr (Irr = 0.016), and the LWD value was 6,921. California had the most fires (nine fires and five injuries), followed by Michigan (six fires and six injuries) and Pennsylvania (five fires and five injuries). Of these states, Pennsylvania had the highest injury risk rate value (Irr = 0.052). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries show an increase during the second period followed by a decrease during the fourth period followed by a small increase during the fifth period and a sharp decrease during the last period. Employees' working hours increased during most of the periods. The Irr values follow patterns similar to those shown by the injury values.

Jan 1, 2004

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By D. J. Parker

Du.ring the past two years a number of oases of successful first-aid treatn . .)nt have been reported by or through the employees of the O. s. Bureau of -anes safety cars and stations. Among such cases are the following: At Benbush, w. Va., a boy or 16 years of age who ba.d just started to work in the mines was trained in first-aid by the crew of Bureau of Mines car 8. The local rr.ine superintendent afterwards reported tba.t a few dS¥s later this boy, Melvin Hollingsworht, found droming in a spring a. baby about three years old who bad wandered away fron.. har.e alone. The boy rescued the baby and perf'oxmed artificial re­suscitation upon it, thu.s saving the child's life. The Schaefer method of resuscitation bad bean ta"Ugbt the boy as a routine art of the regular first-aid course.

May 1, 1922

By Todd M. Ruff

The lack of visibility near earthmoving equipment resulted in six fatalities in U.S. surface mining operations during 2003. These accidents were the result of either a piece of equipment striking another vehicle or worker, or the equipment traveling over the edge of an embankment. Figure 1 is an example of a recent accident that resulted in serious injuries to one worker and fatal injuries to two others when a van parked in front of a haul truck. Two fatalities occurred in separate incidents when front-end loaders struck workers. Another two workers were killed when their equipment backed over the edge of a highwall or dump point [1]. There is clearly a need to provide better information to equipment operators regarding their surroundings. [ ] Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are working to reduce these accidents by developing systems that sense obstacles and changes in terrain near the equipment and provide this information to the operator. Many off-the-shelf proximity warning systems that were developed for automobiles, light trucks, and recreational vehicles were evaluated on off-highway dump trucks [2]. Many limitations were found with existing systems, including frequent false alarms, limited detection range, a lack of specific information on an obstacle (e.g., location, identity), difficulties in finding suitable mounting locations, and an inability to withstand the environment. These limitations have necessitated the development of new systems designed specifically for large, off-highway, earthmoving equipment. New off-the-shelf systems available for mining equipment include radar and tag-based detection systems. Prototype systems now being developed include a proximity warning system based on the Global Positioning System (GPS) and a computer-assisted stereovision system. Development of these new systems was accomplished by working with manufacturers to modify existing systems to meet the needs of surface mining and through cooperative research with organizations to develop completely new solutions. A typical proximity warning system consists of a sensor or antenna mounted on the equipment that detects the presence of obstacles and an alarm interface in the cab of the equipment. Some systems, as described in more detail below, also require that other vehicles and personnel on the ground be outfitted with electronic tags that transmit an “I’m here” signal back to the system (e.g., radio signal detection systems or GPS). Many types of proximity warning systems are on the market, but they are not all discussed in this paper. APPROACH In past work, engineers at NIOSH evaluated several off-the-shelf proximity warning technologies in order to verify their effectiveness on off-highway dump trucks [2]. Dump trucks were chosen because of the number and severity of accidents involving this type of equipment and because extensive blind areas around these trucks are typical. This experience allowed engineers to limit the number of systems chosen for long-term tests at mine sites to those systems showing

By H. B. Humphrey, J. J. Forbes

"In accident prevention, a study of statistical data is necessary to determine primary causes of accidents to devise means to eliminate causes at the original sources. Explosions in coal mines of the United States during the 10 years ending December 31, 1931, ranked third in the causes of fatal accidents; they constituted 16.2 per cent of all fatal accidents in bituminous mines and 8.4 per cent of all fatal accidents in anthracite mines. A study of coal-mine explosions in Pennsylvania, with approximately 160,000 men employed in anthracite mines and about 145,000 in bituminous mines or about 205,000 out of -the approximately 525,000 men employed in all coal mines of the United States, should give information of value to all persons endeavoring to reduce or eliminate coal-mine explosions. This circular reviews explosions of gas or dust or of both in the coal mines of Pennsylvania to show the hazard of gas and dust, to point out the influence of certain factors in causing explosions, and to emphasize the efficacy of explosion-preventive measures.The data published annually by the State Department of Mines and of the United States Bureau of Mines were used in compiling the tables of explosions. Through the cooperation of W. H. Glasgow, secretary, Department of Mines of Pennsylvania, and his assistants, many doubtful cases were clarified, so that as far as recorded the history is comparatively complete. Figures used in compiling some of the tables were furnished by W. W. Adams, chief statistician, demographical division, United States Bureau of Mines.Anthracite in the Wyoming Basin of Pennsylvania was used locally by gunsmiths in 1755, by blacksmiths in 1769, and as domestic fuel in 1808.Mining and shipments developed slowly between 1806 and 1812, but more rapidly after that.Early mining along the outcrops gave essentially no trouble from gas, but by 1870, when State inspection was established, explosions were frequent; ventilation was crude and accumulations of gas were generally ""brushed"" or burned out.Table 1 lists 1,232 ignitions and explosions of gas in anthracite mines from 1870 to 1932, inclusive, every one of which was accompanied by loss of life. Some details are given of 110 representative cases in which five or more lives were lost or in which it appeared that some violence was present.During the period 1870 to 1932, inclusive, gas explosions caused 2,213 fatalities, or an average of about two deaths for each ignition or explosion. Records are not available as to the number injured in these and in other explosions where no deaths occurred, but from a study of explosion reports it appears probable that the number injured exceeds the number killed. In the 110 cases described, 599 were killed and 294 were injured. As shown in Table 2, fatalities from gas explosions averaged 8.3 percent of the total fatalities in Pennsylvania anthracite mines from 1870 to 1931, varying from 6.0 percent in 1931 to 13.1 percent in 1927."

May 1, 1933

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.