Search Documents

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By D. A. Hill

Introduction The fields of an infinite line source in the presence of a conducting half-space have been examined by Wait and Spies (1971). In any real communication link using a current-carrying cable for the transmitting antenna, the cable is of finite length. Here we examine the fields of a finite length cable carrying a constant current in the presence of a homogeneous conducting half-space. The constant current assumption is valid at sufficiently low frequencies when an insulated cable is grounded at the end points (Wait, 1952; Sunde, 1968). Here we examine both surface and buried cables since both downlink and uplink communication links are of interest. Also, we examine both frequency and time solutions since either CW or pulsed communications may be used. Finally, it is necessary to include both magnetic and electric field solutions since reception could be with either loops or dipoles. Since the finite cable solution is more complicated than both the infinite line source and the short dipole solutions, we explore under what conditions a cable appears to be either infinitely long or very short. Some special cases, such as- the low frequency limit, permit analytical solutions which exhibit the dependence on various parameters, such as cable length, quite clearly. Frequency Domain Subsurface Fields The geometry of a line source of length 2[l] located on a conducting half-space with the observer in the half-space is shown in Figure 1. The fields

Jan 1, 1973

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

This chapter analyses the parameters influencing initial design of communication systems, for new mines and upgrading existing systems. Paragraph 5.2 outlines those variables that must be taken into account during the design stages of a new wired phone system. Recommended features, general requirements, and how they can be implemented are treated in this section. Paragraph 5.3 describes ways of improving or extending the range of trolley carrier phone systems and pager phone systems already installed in the mine. 5.2 New Phone System Design The task of designing an adequate communication, control, and monitoring system for an underground mine must be addressed on a system basis. In addition to insuring that effective voice communication is established, any new system should take into account present and future requirements of remote control and monitoring functions. Chapter 4 illustrated the drastic savings in response time that can be realized when remote control and monitoring are integrated into the overall communication system. The importance of including control and monitoring in the overall design plan for any system cannot be overemphasized. Because each mine is unique, and thus usually has its own special operating characteristics and communication requirements, there is no such thing as "the one best system" to meet the requirements of all mines. The optimum communication, control, and monitoring system for a mine must be one that has been tailored to meet the special requirements of that particular mine. Factors that must be considered during system design include- a. Type of mine and mining methods (low- or high-seam coal, deep hardrock mine, stope caving, longwall, room and pillar, etc.). b. Maximum number of working sections. c. Expected mine growth rate and eventual maximum size. d. Haulage methods (tracked trolley, diesel, belt, etc.). e. Underground power distribution system (dc, ac, or both). f. Features desired (two-way radio paging, private line capability for emergency use, etc.). g. Redundant or backup systems for use during outages of the normal system. Although no two mines are alike, the following items have been established as the main characteristics desired for any underground communication system: 1. Multiple Communication Paths to Outside--the objective here is to give all telephones a second method of communicating with the surface. 2. Audible Emergency Signaling--the communication system provides the main means of alerting miners during emergencies. The system should include means to broadcast distinct audible signals for emergency signaling. Initiation of these signals should probably be controlled from. a central outside point, such as a surface control room. 3. Emergency Override--provisions should be included to permit any conversation to be overridden with emergency communication. 4. Selective Area Page--as mines grow larger it is apparent that the entire telephone system paging mode need not be activated each time a call is initiated. When the general area of a

Jan 1, 1984

By D. Harrington

In general, mining is carried on underground, that is, in confined places where it is difficult to obtain adequate lighting and frequently in rock strata requiring much care to prevent caving. Moreover, explosives must be used in mining with the numerous hazards associated with them, and some mines give off explosive or irrespirable gases; also, ma- chinery must be used, usually under conditions much more hazardous than on the surface. These and many other considerations cause mining to be probably the most hazardous occupation in which large numbers of our fellow countrymen are employed. Prevention of accidents in the mining industry is far more complicated than in surface industrial work, even of the more hazardous types, because the different elements that enter into possible accident occurrence are ascertained more readily above ground and suitable action can be taken against them; moreover, errors in connection with prevention of accidents in surface industrial work usually affect only one or, possibly, a few persons, while in zines one human error may readily cause an explosion or other untoward occurrence resulting in the death of scores or even hundreds of persons. This difficulty in the prevention of accidents in and around mines is well-known, and most countries and States have regulations to guard the safety and, to a much smaller extent, the health of workers in mining and allied industries. In general, the State laws and regu- lations regarding the welfare of mine workers are merely a skeletonized outline of some more or less fundamental minimum requirements and are far too general to do much more than suggest some procedure which may or may not be safe or healthful. Most of them are grotesquely out-of-date as applied to present-day conditions, and none of them is adequate to protect life, limb, health, or property. Unquestionably, there is great need for a closer correlation of the laws and regulations of the various States with regard to safety in the mining and allied industries, and while mining conditions vary far too much for a standardized mine safety law applicable to all of the States, on the other hand there are numerous standard and fairly fundamental safety pro- visions which apply to all mines and which should be embodied in the mining codes of all States. Undoubtedly, these standardized safety requirements would be opposed by a consider- able part of the industry, but the ultimate effect would be beneficial to the owners, work- ers, and the general public. For many years progressive mining companies in the United States have not been satisfied to operate only within the meager safety requirements of the State laws or regulations and have adopted additional and far more effective safety procedure of their own, although com- plying also with the State laws and regulations. As a result of this forward-locking policy, zany of these companies have made astonishing progress in the reduction of accidents.

Dec 1, 1935

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

Measure dangerously high concentrations (20 to 500 g/m3) of flammable, airborne dust. Approach Development of high concentration dust monitor (HCDM) which will measure mass concentrations of air borne dust by the principle of beta-ray attenuation. How It Works The HCDM is a battery powered, portable instrument that weighs 10.5 kg. It is capable of making continual (10 sec. time resolution) measurements of high concentrations of airborne dust and can record up to 8 hours of data in an internal memory. The data can be read out later on an analog or digital recorder. An internal pump pulls airborne dust into the sampling section, which contains a low-energy beta-ray source and a Geiger counter detector. No beta radiation escapes from the instrument, and no license is required for the operator. The mass concentration measurement is made while the dust is still airborne. Beta-ray attentuation is independent of particle size and composition of the dust, so the HCDM can he used with many types of dusts which may be airborne in flammable concentrations. A knowledge of the composition and minimum explosive concentration of the dust is necessary to understand the significance of the data from the HCDM. The HCDM was designed to measure air-

Jan 1, 1982

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

Homans [1950] offered a working definition of group that is useful for this research: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at secondhand, through other people, but face-to-face." This chapter begins with a discussion of the group concept in reference to the hypothesized escape groups mentioned earlier. It then moves to an examination of analysis techniques used by the authors. Finally, the subjects themselves are profiled according to their demographic characteristics. The Nature of Groups Warriner [1956] took a realist approach to understanding groups: "(1) the group is just as real as the person, but (2) both are abstract, analytical units, not concrete entities, and (3) the group is understandable and explicable solely in terms of distinctly social processes and factors, not by reference to individual psychology." Warriner's realist position merely holds that "group" occupies a different domain in which it is no more or less concrete than "person." At this group level the unit of analysis will be those relations that indicate social rather than individual behavior. It is possible to investigate these group properties empirically-if a researcher avoids confusing conceptual entities with concrete ones. Most people seem to accept that group attributes must somehow be inferred, but think personal attributes will be directly manifested, requiring little or no interpretation [Snizek 1979]. In other words, nobody would equate physical components of an underground working section with the actual work group, yet social scientists (as well as laypeople) very often confuse real individuals with notions of the person. In actuality, neither groups nor persons are directly disclosed to the senses; both are inferred by experience and observation. One can "see" a group just as clearly as one can "see" a person, given the proper perspective from which to do so. It is necessary, in developing this perspective, to begin with a sound definition of the thing being examined. Besides communication, or more generally, social interaction, Homans [1950] included three other components of group makeup. "Sentiment" is characterized as the feelings people tend to form about one another when they interact often. These feelings include not only friendliness and dislike, but attitudes such as approval or disapproval. A "norm" is an idea, held in common by group members, that specifies how people ought to behave in given circumstances. In lay terms, norms are simply those informal rules individuals abide by in order to get along together in social situations. Finally, "activity" refers to those things persons do with others. In work groups, as an example, many of the activities are cooperative and goal-directed.

Jan 1, 2000

By D. G. Kuehn

Mass spectrographic studies have been conducted on the positive ions and neutral species of glow discharges containing 1.0 pct S02 and 1.0 pct CO in helium. Measurements were conducted for gas pressures from 3.5 to 10.1 torr using both dc and 60-Hz ac excitation. The ion species that were observed included S+, SO+, SO+, 0+, O2+, C+, CO+, and CO2+ with lesser amounts of SO3+, (CO)2+, SCO+, and (SO?CO)+ or CS+2. Interpretation of the functional dependence of the various ionic and neutral species on pressure and applied power showed that CO reacted with the SO formed in the discharges to produce CO2 and sulfur. Deposition of elemental sulfur was observed in the plasma container.

Jan 1, 1973

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark- Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

By A. J. Barry

To determine the torque-load relationship for SIB-inch (nominal)-diameter roof bolts, the Bureau of Mines tested 5 makes of expansion shells and 2 types of bolts (regular and high-strength) in 2 sandstone and 2 shale mine roofs. Unused flat-steel bearing plates in as-received condition were used in these tests. The relationship between torque and load was found to be approximately 50 pounds of load per foot-pound of torque for both the regular and high-strength bolts. This relationship is valid up to 130 foot-pounds for the regular bolts and up to 175 foot-pounds for the high-strength bolts. A torque of 130 foot-pounds on a regular bolt will produce a load of 6,150 ± 1,910 pounds 90 percent of the time, and a torque of 175 foot-pounds on a high-strength bolt will produce 8,050 ± 2,750 pounds 90 percent of the time. Above these values, the torque-load relationship tends to be erratic due to binding between the bolt and plug threads. Binding causes excessive torque to be expended in producing torsion in the bolt rather than tension. This torsion adversely affects the yield load of the bolt. Therefore, the installed torques should not exceed the 130-and l75-foot-pound values. A statistical analysis of the data showed that the torque-load relationship was not significantly affected by the type of bolt or expansion shell unit but might have been affected by the type of rock.

Jan 1, 1956

By M. F. Dunn

A handbook to provide a quick reference guide for selecting and using jet fans in a variety of conditions was prepared. The document is intended for use by front-line supervision, ventilation engineers, and mine planners. Included are discussions of jet fan characteristics, selection and use critieria, and do's and don't's for easier operation, safety, and performance. The handbook is based on research at three underground metal/nonmetal mines having cross-sectional areas of 900 to 2,000 ft2.

Jan 1, 1983

By David K. Denton

There are no active mines in the Mt. Eddy RARE II area. Chromite, gold, and stone prospects were examined. The RARE II area contains no identified mineral resources; however, a sample of a 260 ton occurrence contained 38.1 percent chromium oxide (Cr203) at the Ratero Prospect (fig. 1, no. 3), which has low potential for chromium resources. The Johnson Mine (fig. 1, no. 6) produced a small unrecorded amount of chromite during World War IT, but only a low potential exists for chromium resources. A low potential exists for gold resources at the Half Century Prospect (fig. 1, no. 2). At a borrow pit northwest of the study area (fig. 1, no. 1), sheared serpentinite is quarried for road metal; similar rock occurs in the RARE II area, but better material is more readily available elsewhere. Sand and gravel occurrences are too inaccessible and distant from markets to be considered resources. Mineral fuels and geothermal resources were not evaluated during this Bureau of Mines study. There currently are three unpatented lode mining claims in the study area. INTRODUCTION The Mt. Eddy RARE II area is 7 air-mi west of Mt. Shasta City, California, and straddles the Siskiyou-Trinity county line. The roadless area includes 7,200 acres of rugged, glacially carved, ridges and drainages which comprise Mt. Eddy. Elevations vary from 6,000 ft along the North Fork Sacramento River to 9,025 ft at the summit of Mt. Eddy. The area is covered with conifer forest below 8,000 ft elevation.

Jan 1, 1983

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

By R. V. Ramani, A. S. C. Owili-eger

Mathematical modeling is a scientific exercise with the objective of developing simplified mathematical statements that relate to one another the same way as the processes that are being modeled. The utility value of the model is dependent on the ability of the model to closely approximate prototype behavior. Development of a perfect model, therefore, is an unrealistic objective because of the simpli¬fying assumptions made in building it. However, for a model to be acceptable for application, its operating characteristics or data generated from it should, within reasonable accuracy, duplicate proto¬performance. The validity and accuracy of a model depends on the mathematical constraints presupposed in model formulation. The final model must be tested for mathematical validity and for closeness of representation of the prototype. Mathematical validity, does not, however, imply that the model is accurate and correct but is prerequisite. Model testing and verification for the steady state model are given in Owili-Eger et al (1973). The unsteady state model has been tested for mathematical validity and found to be correct but has not yet been applied to a field condition for lack of data. However, in the application discussed below, the unsteady state model results are compared with pressure curves reported in literature and also with results from the steady state model. Coal seam characteristics and gas reservoir pressure used in this application are extracted from Kissell (1972). These characteristics are for the Pittsburgh seam, Federal No. 2 Mine, Fairview, West Virginia.

Jan 1, 1974

Lower the respirable dust expo? sure of longwall shearer operators Approach Use improved water sprays on the shearer machine to direct the dusty air toward the face. In laboratory tests and actual mining conditions, the shearer-clearer has proved to be an effective dust control technique. Recent field experience however, has indicated that not enough technical information is available on proper installation of the improved shearer-clearer. This Technology News will provide details of the Improvements made to the shearer-clearer and provide guidelines for installing the system. How It Works The shearer-clearer system consists of several strategically-mounted water sprays and one or more passive barriers. The sprays redirect the airflow around the shearer into both a clean and a contaminated split. The sprays confine the contaminated split or dust cloud to the coal face, allowing the shearer operators to remain in the clean split on the walkway

Jan 1, 1986