Search Documents

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Edward D. Thimons

The Bureau of Mines conducted in-mine tests to determine correction factors applicable to low-velocity airflows (below 150 fpm) measured by the smoke cloud, vane anemometer, and oil of wintergreen tracer gas techniques 0 The average correction factors found for these methods of measurement were lower than those reported in the literature for use with higher velocity measurements. All tests measured airflows with controlled average velocities ranging from 50 to 100 fpm. Correction factors averaged about 0.75 for readings taken by the centerline smoke cloud method, remotely controlled and stickheld center" line anemometer, and split traverse stick-held anemometer. For hand-held centerline anemometer and oil of wintergreen tracer gas readings, correction factors averaged about 0.67. Since special anemometers are needed to measure airflows in this low-velocity range, and since proper calibration of these anemometers is difficult and expensive, the use of anemometers for low-velocity measurement is imprac-tical. On the other hand, smoke and oil of wintergreen give results as con-sistent as those obtained with specially calibrated, low-velocity anemometers. Furthermore, they are easy to use and inexpensive.

Jan 1, 1979

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By R. Van A. Mills

This preliminary paper is intended to answer briefly some of the inquiries coning to the Bureau of Mines regarding the so-called "paraffining", of oil wells and methods of preventing and remedying that trouble. The increased difficulties in operation and the losses of production caused by the deposition of gummy and waxy hydrocarbons, commonly called paraffin, in the wells, tubing, other pumping equipment, and in the pores of the productive sands, have long been recognized but the trouble has not been overcome. The nature and causes of the trouble, together with some of the possible methods by which it may be diminished or overcome, are outlined below. Character of the Peraffining Materials. The so-called paraffin that collects in oil wells end in the pores of the oil-producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or lees water, oil, and inorganic silt. Some of the samples of this "paraffin" collected from oil wells in different fields and examined by the Bureau of Mines contain as mach as 20 per cent by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this "paraffin" is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulphates of calcium, barium, and strontium are less common constituents of the "paraffin."

Jan 1, 1923

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2000

By B. Olson, V. A. Marple, D. J. Radet

"Gravitational forces have been found to be an important factor in defining the particle collection efficiency curve of inertial impactors for large particles. In general it was found that if the parameter G = gW /V 0 2 (g is the gravitational acceleration. w is the nozzle diameter and V 0 is the average fluid velocity at the nozzle throat) in greater than 10-3 the efficiency curve would shift to lower panicle sizes. No effect could be seen for lower values of G.IN'IRODUCTIONInertial impactors have long been used as classifiers for airborne particles. By proper design of the nozzles and flow rate it is possible to classify particles with a fairly sharp cut in the particle size range from approximately .02 µm to 50 µm. Because of inertial impactors wide usage they have been extensively studied calibrated and evaluated. Most of these studies have been experimental calibrations of single stages using monodisperse aerosol particles. However, due to impactor simplicity. i.e. a jet of particle laden air impinging upon a flat plate with large inertia particles crossing the streamlines and impacting upon the plate the impactor also lends itself to theoretical evaluation.The most comprehensive method for analyzing impactors theoretically is to use finite difference solutions to the Navier-Stokcs equations and solve for the velocity components and pressure at node points of a grid placed over the area of interest. Using iteration and relaxation techniques the value of the velocity vectors can be determined at these node points with good accuracy. Once the velocities arc known, theoretical particles of known size can be placed into the now field and their trajectories determined by analyzing their equation of motion using numerical methods.Rader and Marple (1985) have performed theoretical analysis on impactors and have included such factors as Ultra-Stoksian .drag and the physical diameter of the particle in their analysis. However, even with these· factors included, there appears to be discrepancy · between the experimental and theoretical results when the particle size is larger than approximately 4 or 5 µm. One possible reason for this discrepancy could be the effect of gravity on the particle as it passes through the impactor. Therefore, a program was initiated to study the effects of gravitational forces on the collection· efficiency of particles in impactors. The results of that study arc presented here."

Jan 1, 1990

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By J. W. Paul

This paper deals with the third phase of on extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Parts I and II of this paper were issued Serial 2621 and Serial 2647 of the Bureau of Mines in July and October, 1924. They dealt with the resistance of unobstructed entry and the resistance caused by mine cars in untimbered entry. Description of the Tests After the resistance of unobstructed entry and of mine cars in untimbered entry had been determined by tests in the Experimental Mine, three different types of timbering were installed in the test section and the increased resistance caused by the timbering was determined.

Jan 1, 1925

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in numerous applications. Normal Accident Theory (NAT) explains that these accidents are inevitable because of system complexity. Complex systems, such as computer-based systems, are highly interconnected, highly interactive, and tightly coupled. We do not have a scientific methodology to identify and quantify these complexities; specifically, NAT has not been operationalized for computer-based systems. Our research addressed this by operationalizing NAT for the system requirements of safety-related computer systems. It was theorized that there are two types of system complexity: external and internal. External complexity was characterized by three variables: system predictability, observability, and usability -the dependent variables; internal complexity was characterized by modeling system requirements with Software Cost Reduction dependency graphs, then quantifying model attributes using 15 graphtheoretical metrics the independent variables. Dependent variable data were obtained by having 32 subjects run simulations of our research test vehicle: the light control system (LCS). The LCS simulation tests used a cross-over design. Subject perceptions of these simulations were obtained by using a questionnaire. Canonical correlation analysis and structure correlations were used to test hypotheses 1 to 3 - the dependent variables predictability, observability, and usability do not correlate with the NAT complexity metrics. Five of 15 metrics proposed for NAT complexity correlated with the dependent data. These 5 metrics had structure correlations exceeding 0.25, standard errors < 0.10, and a 95% confidence interval. Therefore, the null hypotheses were rejected. A Wilcoxon signed ranks test was used to test hypotheses 4 to 6 - increasing NAT complexity increases system predictability, observability, and usability. The results showed that the dependent variables decreased as complexity increased. Therefore, null hypotheses 4 to 6 were rejected. Lastly, this work is a step forward to operationalize NAT for safety-related computer systems; however, limitations exist. Opportunities addressing these limitations and advancing NAT were identified. Lastly, the major contribution of this work is fundamental to scientific research - to gain knowledge through the discovery of relationship between the variables of interest. Specifically, NAT has been advanced by defining and quantifying complexity measures, and showing their inverse relationship to system predictability, observability, and usability.

By David M. Hopstock

To help assure an adequate supply of minerals to meet the Nation&apos;s economic and strategic needs, the Bureau of Mines is conducting bench-and pilot-scale research using wet high-intensity magnetic (WHIM) separation to recover iron from oxidized taconites of the. Lake Superior region. The advantages and disadvantages of WHIM separation in relation to other separation methods, the most recent innovations in WHIM flowsheet design, and the role of mathematical models in process optimization are discussed.

Jan 1, 1979