Search Documents

By C. E. Coleman, Joseph D. Davis

During some distillation experiments conducted by the Bureau of Mines in cooperation with the Trent Process Corporation it was observed that amalgams of heavy petroleum oils and finely pulverized coal tended to produce a denser coke than that obtainable from the coal when retorted alone . Even anthracite coal when retorted with oil yielded a coke . This led the writers to believe that by mixing a lowrank coal ( sub-bituminous or even lignite ) - with asphaltic oil and retorting it, a coke suitable for domestic fuel could be made . Thus there was contemplated the production of domestic coke and the utilization of a low- grade oil in one operation . - In order to decide on the practicability of this process , it was necessary to know the value of products obtainable by such a method , as compared with those obtained by separate distillation . A laboratory method was therefore devised , and while it was realized that no small - scale testing apparatus for destructive distillation gives results that are directly applicable to commercial - scale operations , by keeping distillation conditions uniform for comparative tests , results were obtained valuable for purposes of comparison . The plan was to distill mixtures of coal and oil in a laboratory retort , and then distill the constituents separately under the same conditions . The comparative quantities of products yielded were thus directly obtained , and their quality was determined by analysis . The following are the main points investigated : ( 1 ) Quantity and quality of coke ; ( 2 ) Quantity of oils boiling below 221 °C . ( gasoline stock) and oils boiling at 221 to 300° C . ( kerosene stock) ; and ( 3) Quantity and quality of gases .

Jan 1, 1922

By Parviz F. Rad

The increased use of tunnel boring machines (TBM) has stimulated laboratory research to optimize the cutting parameters of these machines with the objective of increasing machine efficiency and penetration rate. Laboratory-scale rock cutting experiments have succeeded in identifying many of the important parameters involved in rock-cutter interaction. Although scaling factors may be required to apply the results directly, the concepts developed can be used qualitatively as design guidelines for boring machines. The Bureau of Mines Twin Cities Mining Research Center has recently developed a large-scale rock cutting device (RCD) that will simulate many of the operating parameters of the tunnel boring machines in the laboratory under a controlled environment. The results of the experiments with this device will be directly applicable to the design of TBM's.

Jan 1, 1973

This U.S. Bureau of Mines (USBM) report conveys the results of an economic analysis of minerals in the West Mojave Management Area (WMMA), including the Desert Tortoise Priority Habitat (DTPH), a proposed special land management area. Undiscovered mineral resources were estimated for the entire WMMA, which totals 8.7 million acres. Known mineral resources were studied for the DTPH, which is an area of 1.2 million acres contained within the WMMA. Federal lands within the WMMA are managed by the Bureau of Land Management (BLM). The WMMA includes Federal, State, and private lands in the western portion of San Bernardino County and the eastern portion of Kern County. The center of the study area is 20 miles northwest of Barstow, California (Figures 1 and 2).

Jan 1, 1993

By David L. Veith

This report summarizes a Bureau of Mines review of selected literature on the effects of subsidence due to high-extraction underground coal mining on farmland areas. The data are presented for consideration in evaluating the subsidence effects due to similar mining techniques on the prime farmland areas of Illinois. In Illinois the ground water level in the glacial drift is only 2 to 15 ft below the nearly flat to gently rolling ground surface. The main subsidence concern is flooding, as caused by the lowering of the ground surface, and the subsequent effects on crop production. Positive drainage must be maintained in the farmlands, and the need exists for extensive regional planning by the mining and agricultural industries to maximize short- and long-term production from both efforts. The Bureau is cooperating with the State of Illinois to develop basic information necessary for such planning.

Jan 1, 1987

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By RV. Ramanl, KV. K. Prasad, M. Swaminathan

The objective of the research in this project is to develop a knowledge based expert system for aiding the planning of mine ventilation systems. This system focuses on mine ventilation system design from a coal mine dust control standpoint. It is recognized that mine ventilation system design is an engineering problem involving not only rote numerical calculations to solve the pressure quantity problem but also substantial judgement and expertise to analyze a problem situation and Interpret the results of an algorithmic program. The thrust of this project is to i) extract this knowledge from public domain sources and recognized experts in industry, government and academia, 11) represent this knowledge in the form of IF ... TI-IEN rules in an expert system (ES) and 111) interface the developed expert system with a mine ventilation network analysis program vis. PSUMVS (Pensylvania State University Mine Ventilation Simulator). By providing the numerical computing and qualitative reasoning aspects of mine ventilation system design in a single Integrated system, better quality decision support will be made available to apprentice users.

Jan 1, 1988

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By Carl Belser

In 1925 the Park Utah Consolidated Mines Co., after several years of experimental work, installed a system for signalling from cages which has been operating efficiently and with low upkeep costs for the post 19 years. The system was adopted for a large western metal mine but was later abandoned be arse of the constantly shifting shaft alinement. Recently the system has been studied and probably will be put into service at two other large mines. One of the principal reasons wry the system has not boon adopted more widely has been the lack of adequate details both as to the desirability of having such a system and as to its construction and operation. Previous signaling, systems contained undesirable features, such as charged bare wires extending the full length of the shaft. Under the direction of O. N. Friendly, then general superintendent of the Judge Mining & Smelting Co., the present system, entailing the use of a samll current at low voltage, was gradually developed. Many of the refinements in the system wore contributed by Leonard Wilson, consulting electrical engineer, Salt Lake City, Utah.

Jan 1, 1945

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

By Russell R. Trengove

The Bureau of Mines developed by core drilling the Cove Meadow copper property, also known as the Patterson property, from May 6, 1949, to August 6, 1949. It is in the Cove Meadow mining district, northwestern Humboldt County, Nev., 102 miles northwest of Winnemucca. The purpose of the work was to determine possible reserves in a mineralized shear zone in andesite that has been partly explored by several surface cuts and two shallow underground workings. Production from this zone to August 1, 1,949, was 98 tons of hand-sorted copper ore assaying 5.1 percent. The development work performed by the Bureau of Mines comprised a study of the geology, mapping the area, sampling the outcrops, and exploring by diamond drilling the shear zone adjacent to the fault. Seven holes were drilled for a total of 1,246 feet. Mineral reserves indicated by the project are confined to a length of 500 feet along the strike.

Jan 1, 1950

By J. A. McAllister

In the course of a study of domestic Manganese resources, 2-ton representative samples of ore were taken by Bureau of Mines' engineers from the Payday claim, Weber County, and the Newcomb-claims, Rich County, Utah. The Payday No. 1 deposit is situated 13 miles northeast of Huntsville, Weber County, Utah. The manganese ore is a. replacement deposit in limestone and consists of manganese oxides imbedded 'in clay and also as the cementing agent consolidating small pebbles and pieces of quartz and limestone.

Jan 1, 1949

By R. D. Currie

"INTRODUCTION Compressed air for operating coal-mining equipment is seldom considered in conjunction with modern methods and appliances. But the Jamison Coal & Coke Co. has proved the economy and efficacy of compressed air for this purpose at its Mine 8 near Farmington, 8 miles west of Fairmont, Marion County, W.. Va., and the mining industry as a whole concedes its superior safety in gassy or dusty coal mines.The uses for compressed air in coal mining are now generally associated with such equipment as coal punchers, chain-breast machines, and to a lesser extent the ""radialaxe"" type of mining machines.Electricity has rapidly superseded compressed air for power in coal mines during the past 20 years; and in the last few years the general, and often unwise, use of electricity at the face region has taken on added impetus through the widespread use of mechanical loading equipment.Some of the unfavorable results of this increased use of electricity are shown in the growing number of mine explosions and fires of electrical origin. In the past four years 59 explosions of this type took the lives of 672 men, or 74.8 per cent of the total number of deaths from explosions were due to explosions of electrical origin.3In 1926, an explosion in Mine 8 of the Jamison Co. killed 19 men. The exact source of ignition was not determined, although it was definitely decided that it was of electrical origin and probably was at an electric coal-cutting machine.Prior to this disaster the company had done some experimenting with compressed-air-driven mining machines, and its Mine 9 had been completely equipped with air-driven chain-breast machines; a few of these machines were also in use in Mine 8. The explosion, however, gave impetus to the adoption by this company of compressed air for operating face equipment. The chain-breast machines were as satisfactory as electric machines of the same type; but the trend in the industry was toward faster cutting machines, which required less physical exertion on the part of the operating crews. A track-mounted machine of the arcwall type was found to be suitable for the conditions and system of mining, so that one of these operated by compressed air was developed by the Jeffrey Manufacturing Co. working with the officials of the Jamison Co.The first of these machines was installed in the latter part of 1926 and additional machines were delivered from time to time, until at present there are nine of them in the mine. Necessary improvements have been made, with the result that a fast-cutting, easily handled, efficient, and safe mining machine has been developed for cutting the hard Pitts¬burgh bed coal of the Fairmont field."

Oct 1, 1932

Roof screening for ground control originated with metal miners in the western United States. At first chain-link fence was used, but because it was so difficult to handle, the miners started installing a more rigid welded wire screen used in the concrete industry. Eventually coal mines in the west began to use screen, and now more and more coal operations, especially longwall mines, are installing roof screen on a regular basis. Screen use has recently increased in the Illinois basin and is now making its way to underground coal mines in the eastern U.S.

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By D. L. Hollis

An arc plasma reactor, constructed and used for studying extractive metallurgical processing, was adapted by the U.S. Bureau of Mines to separate gases of different masses by using the high rate of plasma rotation. With argon and helium as input gases, peripheral reactor outlet ports had a measured average increase of about 10 pet in argon concentration relative to helium with the plasma on compared with plasma off for the same gas inlet concentrations in both cases. Approximately the same average increase in argon concentration occurred from the peripheral outlet port compared with a central outlet probe with the plasma on. There was no difference with the plasma off.

Jan 1, 2010

By William L. Crentz

1. SALES PUBLICATIONS

Nov 1, 1949

By P. D. Kovscek

High-pressure streams of water, known as water jets, can be used to improve the cutting efficiency of mechanical bits. During prior testing by the Bureau of Mines, the cutting performance of a longwall shearer, equipped for water-jet-assisted cutting, was evaluated. The performance of the shearer did not improve while using water jet assist because the pressure of the water delivered to the rock surface was inadequate. The study, described in this report, resulted in a determination of the major cause of water pressure loss on the shearer, and an evaluation of the techniques for increasing the water pressure at the rock surface. The results show that the major pressure loss, which occurred between the nozzle and rock surface, is directly affected by the amount of fluid turbulence that develops just upstream from the nozzle. Preventing a sudden change in the direction of the flow channel can increase the stagnation pressure as much as 400 pct. Smoothing the surface of the flow channel in the shearer bit block would increase the stagnation pressure delivered to the rock surface by 35 pet.

Jan 1, 1989

Develop a technology for producing high-quality hake graphite from the steelmaking waste known as kish. Approach Treat the waste kish as an ore and apply mineral processing techniques of physical beneficiation and chemical purification to produce a range of graphite products com¬petitive with the natural mineral. Background Graphite is a naturally occurring form of carbon with a unique combination of properties that make it indispensable in a very wide range of industrial and consumer applications. It has high electrical and thermal conductivity and remains stable to extremely high temperatures It has a low coefficient of friction and is nearly impervious to corrosion. The steel industry is dependent on graphite in clay-, magnesia-, and alumina-bonded refractories for crucibles, bricks, facings, and coatings. Electrical uses include graphite brushes in motors and generators, and electrodes in batteries. The transportation industry needs graphite for clutch and brake linings, and all industries depend on graphite in seals, gaskets, lubricants, and coatings. The consumer sees graphite in composite plastics and in the common pencil. As with all natural minerals, the availability of graphite is diminishing and costs are rising as quality decreases.

Jan 1, 1993

The principal activities of the Bureau of Mines Pittsburgh Mining and Safety Research Center during fiscal year 1971 (July 1, 1970, to June 30, 1971) are reviewed in part 1 of this paper. Part 2 summarizes publications during fiscal year 1971.

Jan 1, 1974

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators' fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993