Search Documents

By C. Harry Benedict

This paper presents the details of milling practice and costs at the conglomerate mill of the Calumet & Hecla Consolidated Copper Co., Lake Linden, Mich., and is one of a series on milling methods being published by the Bureau of Mines. GENERAL DESCRIPTION The mines of the Calumet & Hecla. Consolidated Copper Co. are located in the Keweenaw Peninsula of northern Michigan. The mines of this district lie in a belt not over 4 miles wide and 100 miles long, which contains more or lees commercial ore. The Calumet & Hecla properties are the farthest north, except for the Seneca, of the operating mines. The district borders on Lake Superior, and by means of the Portage and Torch Lake waterways the largest lane vessels, can transport coal and other supplies from the lower Lakes directly to the company docks.

Jan 1, 1930

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workmen enter these places, but due to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected, to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By Kris Chatrathi, John E. Going, Kenneth L. Cashdollar

Two types of flammability limits have been measured for various dusts in the Fike 1-m3 (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m3 vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1- m3 vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By R. R. Schehl

The Bureau of Mines analyzed the structure of a high-grade metallurgical coke, carbonized at different temperatures in the range 500° to 1,000° C, through X-ray diffraction studies. Growth in the crystallite size with increasing coking temperature was calculated from profile analysis and compared with values obtained from the radial distribution function. The carbonization temperature appeared to have little influence upon the stack height, whereas the layer diameters more than doubled in size between 500° and 1,000° C. These results are comparable to those obtained from other studies of poorer quality cokes.

Jan 1, 1974

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By Michael J. Klishis

It was the goal of this project to develop training materials specific to two areas of the mining industry: (1) safe use and care of the self-contained self-rescuers, and (2) awareness and avoidance of electrical hazards. This report describes the development of the following training material: Instructor's modules for the OCENCO EBA 6.5, CSE AU-9A1, and PASS 700E self-contained self-rescuers; and a textbook, slide tapes, and accident case study scenarios for mine electricity, and a computer based instructional package on mine electricity and electrical hazards. The report concludes that additional efforts are needed in mine training and four recommendations are made: (a) tailor existing materials to fit specific mine sites, (b) develop and evaluate computer based instructional material, (c) develop parallel training materials for metal and non-metal mines and, (d) develop additional training materials for preparation plants and surface areas of underground mines.

Jan 1, 1985

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By Thomas L. Vandergrift

This U. S. Bureau of Mines (USBM) report evaluates three stress-transfer-modification concepts for their potential in reducing longwall gate road stresses and closures. In each of the three concepts - packwalling, gob infilling, and entry filling -support structures are constructed on the headgate side of the panel parallel with or inby the face line. When the headgate becomes the tailgate of the adjacent panel, these structures are in place to accept stresses transferred from the mined-out panel. Using the USBM nonlinear boundary-element program MULSIM/NL, baseline models of typical longwall stress transfer behavior were developed for both intermediate depth and deep mining conditions. These models were verified by comparing model results with field measurements and observations. The stress-transfer-modification concepts were then incorporated into the deep baseline model to quantify the effects of each concept on tailgate closure. Modeling results indicated that entry filling is the most effective concept in reducing tailgate escapeway closure. Using only 18 m3 of a weak fill per meter of face advance (7.3 yd3 per ft of face advance), tailgate escapeway closure was reduced by 33%. By improving the quality of the fill, similar results were achieved using 50% less volume.

Jan 1, 2010

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By W. H. King

"INTRODUCTION The manganese deposits of the Drum Mountain area were investigated as two separate projects. The first was begun in November 1940 and completed in August 1941, and the second began in January 1945 and ended in May of the same year. The first project was initiated as part of the Bureau of Mines program for development of strategic minerals for national defense. Subsequent operations disclosed conditions somewhat different than were expected, and it was decided that additional drilling should be done to delimit the ore bearing horizons further.The more promising manganese deposits in the Drum Mountains are situated on properties known as the Staats manganese mine and the Pratt manganese mine. The property controlled by the Pratt interests is under lease to the Ward Leasing Co. The 1941 project investigated the deposits on both properties, whereas the 1945 project was planned to explore further the oxidized ore bodies of the Pratt mine, although one hole was drilled in an attempt to extend the carbonate ore body on the Staats property (fig. 1).ACKNOWLEDGMENTSIn its program exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Jan 1, 1947

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974