Search Documents

By John M. Devine

Hydrogen sulphide associated with natural gas was noted as early as at Point Albino, Canada. The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence was by no means common. However, in recent years, with the development of the producing zones of test Texas and the Texas Panhandle, the Production of "sour" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor--frequently a major problem--in the drilling and operation of many wells in those areas. The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen iron the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.

Jan 1, 1931

By M. J. Spendlove

A progress report is presented on a research program in which an attempt was made to develop a practical sulfide-volatilization process for recovering tin from low-grade Bolivian ores. Shaft-furnace designs and operating techniques were studied in a series of experiments in which the objective was to sulfidize cassiterite to stannous sulfide, remove the stannous sulfide by volatilization, reconvert the stannous sulfide to stannous oxide, and collect the resulting fume. A shaft furnace was developed and operated in a final test in which many of the previous difficulties were surmounted. Since the supporting funds were exhausted at this point, the project was discontinued; recommendations for further improvements in furnace design and operation were made on the basis of interpretation of experimental results obtained in shaft-furnace experiments and other related studies.

Jan 1, 1955

By Bergerm L. B., S. J. Davenport

"INTRODUCTION Oxygen, because of its vital relationship to man's physical well being, is the most important chemical_ element. It may be breathed, however, only in a rather limited range of concentrations and pressures without producing ill effects. An excess of oxygen may be equally as harmful as too little of it. Because of the importance of these effects, the study of the physiological action of oxygen has received attention for many years and by many investigators. Much of the investigative work has been directed toward determining the limits within which oxygen in abnormal concentrations and at abnormal pressures may be breathed with safety in such applica¬tions as deep-sea diving, work in comprossod-air, aviation, the wearing of apparatus designed to permit entrance into irrespirable atmospheres, and in the therapeutic applications of the medical profession.The Bureau of Mines frequently receives requests for information on the effects of breathing essentially pure oxygen, because of the Bureau's association with the use of self-contained oxygen breathing apparatus for entering irrespirable mine atmospheres, and the use of oxygen in conjunction with artificial respiration as a moans of resuscitation. The purpose of this paper is to summarize briefly the effects upon the human body of the inhalation of oxygen in various concentrations and at various pressures and to give reference to other published information that deals in greater detail with the diverse phases of the subject. The literature in this field is voluminous; therefore, a complete bibliography has not boon presented in this paper. No paper on this subject would be complete without reference to the classic pioneering work of Paul Bert (1) 3/ in this field. Articles such as those of Stadia, Riggs, and Haugaard (2), Bean (3), Specht (4), and others cited contain extensive lists of references that will leadthe reader to information in a degree of detail that is not within the scope of this publication."

Jul 1, 1950

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker's dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988

By R. S. Fowkes

The Bureau of Mines constructed a fully automated pilot plant facility to study the hydraulic transportation of solids through a lock hopper feeder system. An equation for the energy requirements to transport coarse solids hydraulically proved applicable to this system. Optimum velocities were obtained for limestone, mine refuse, and bituminous coal. The experimental data, calculations, and graphs show the effect of velocity, specific gravity, and solids concentration on head loss and power requirements. Other data were obtained and evaluated to determine the effect of particle size on head loss. Results also are given for (a) tests using friction reducing polymers; (b) tests using seven test sections of steel alloy pipe to determine their wear characteristics; (c) tests to determine spatial segregation of moving particles; and (d) tests to determine the effect of shape, size, and specific gravity on particle velocity in a horizontal pipeline. The lock hopper feeder system was found practical for continuous hydraulic transportation of the material types and size ranges tested.

Jan 1, 1969

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The Objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By K. K. Kershner

This report describes an investigation by the Bureau of Mines designed to provide background data for extending and improving the applications of chlorine metallurgy in extracting metals from ores. Optimum conditions are given tor chloridizing galena, sphalerite, and chalcocite by contact with chlorine gas. Petrographic and chemical analyses of the sulfides used in the experiments are listed. Graphs are furnished showing the extent of chloridization of each metal sulfide over the temperature range of the observations. In each case, the first tests were made with the reaction chamber at room temperature. This temperature was increased by regular increments in succeeding tests until the temperature was reached at which quantitative conversion of the sulfide to chloride was observed. The data are also plotted for screen-size fractions of the sulfide minerals investigated. Data show that the extent of metal chloride formation was affected by chloridization time, particle size of the sample, and usually, the temperature of the reaction chamber. At 300° to 400° C. an anomaly was noted for both galena and sphalerite. The temperature at which this anomaly was observed varied according to the particle size of the mineral. Comparisons are made between the chloridizing characteristics of the mineral sulfides and their chemically prepared counterparts.

Jan 1, 1961

By J. Kruttschnitt

This paper, describing milling practice at Mount Ira Minis, is one of a series covering milling methods and cost that is being published by the Bureau of Mines, United States Department of the Interior. The Mount Isa concentrator began operations in day 1931 by treating a mixture of oxidized and sulfide ores. Since March 1935 only sulfide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulfide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulfide ore per day. The installation of additional crushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2,240 tons of sulfide ore daily.

Jan 1, 1939

By Thomas M. Garland

A field study was made by the Bureau of Mines in cooperation with oil companies to determine the feasibility of changing the injection profile of water-input wells after water breakthrough at producing oil wells. A secondary objective was to study the particle size and quantity of plugging material required to change the input profile and the methods of applying these materials. Fifty-three injection wells were treated with various amounts and types of plugging materials and the injection profile was definitely changed in most of the wells treated. Increased efficiency of water injection after treatment was indicated by tracer surveys and injection-well performance. There were some indications that the rate of water production was reduced and the rate of oil production was increased as a result of selective-plugging treatments, but ,s found that an immediate change in the rate of oil and water production did not normally occur. In many cases, beneficial results from a treatment may never be observed in the rate of oil or water production due to the many factors that affect the performance of producing and injection wells.

Jan 1, 1966

By M. B. Bransford

A calculation procedure was evolved by the Bureau of Mines for determining the heat-transfer characteristics of dilute gas-solid mixtures in an externally heated tube. The procedure accounts for differences in gas and particle velocities and covers a range of particle sizes. Heat transfer coefficients obtained by the calculation procedure are compared with values reported in the literature.

Jan 1, 1970

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By Ernesto Villaescusa, Andres Brzovic

Rock masses of the primary copper ore at the El Teniente Mine are very competent and massive. The rock mass contains almost no open discontinuities. Nevertheless, there is a high frequency network of small discontinuities coupled with widely spaced faults. A data collection campaign designed to characterize the rock structure was recently implemented. The results show that conventional analysis in terms of discontinuity frequency does not predict differences between two studied sectors. However, when an empirical definition of a weak discontinuity is applied, appreciable differences between the two sectors appear in terms of discontinuity frequency and predicted in situ block size distributions. These differences are in accordance with actual observations at the mine site. Due to the geological features of the primary copper ore, rock mass classification schemes cannot be readily applied to characterize these rock masses.

Jan 5, 2007

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

By Daniel Edelstein

Demand for arsenic trioxide dropped markedly during 1983, primarily as a result of a 27% reduction in cotton planting. As an oversupply of arsenic trioxide developed, prices declined for both domestic and imported material. Domestic Data Coverage.-Commercial-grade arsenic trioxide and arsenic metal were produced by only one U.S. company, which voluntarily reported its production to the Bureau of Mines. To prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1984