Search Documents

By T. Estelle Gardner, A. R. Taylor

Heat capacity measurements were made on sodium bromide ( NaBr ) and sodium iodide ( NaI) in the temperature ranges of 7 ° to 300 ° K and 56 ° to 300 ° K using an adiabatic calorimeter . Smooth values of heat capacity, entropy , enthalpy function , and free- energy function were calculated from the heat capacity data at 10° K intervals and at 273.15° and 298.15° K. Entropy and free energy of formation values at 298.15° K also were calculated for the two compounds using entropy values determined in this study and other data reported in the literature . The entropy values calculated at 298.15 ° K were 20.75 ± 0.06 entropy units (eu ) for sodium bromide and 23.55 ± 0.07 eu for sodium iodide .

Jan 1, 1964

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By Oliver Q. Leone

Electrorefining tests using titanium-nitrogen alloys as anode material showed that no significant quantity of nitrogen was transferred to the cathode deposit. The nitrogen of the anode remained in the scale, and the titanium-nitrogen alloy was anodically insoluble in the electrolyte when the nitrogen content was 11 weight-percent.

Jan 1, 1966

By E. J. Lintner, J. R. Thoenen

During the period 1937-40 and until peacetime research was superseded in 1941 by wartime activities , the junior author was engaged in studies regarding the relative efficiency of operating methods in quarries producing crushed stone for mineral aggregates . The results of some of these studies were published as reports of investigations in 1939 and 1940 ; / others were discontinued due to war demands on personnel and time . The published reports discussed the efficiency of particular quarry operations with respect to the time consumed and without reference to costs or mechanical factors . • At the time , the field data were collected for the published reports other data were collected relative to the relationship of the numerous variable factors inherent in the operation of a churn drill to the ability of the drill to produce blast holes . The churn drill is essentially a crusher and depends. for its performance upon the foot-pounds of energy it can impart to the cutting edge of its bit . The gravity stamp mill , so well-known in western gold mines , is essentially the same type of crusher . The ratio of foot- pounds necessary to crush the rock , to the total theoretical energy developed by the falling churn- drill tools , affords a good means of evaluating the efficiency of the tool . This does not include to tal over-all efficiency involving the mechanical equipment of the drill itself or its power unit .

Jan 1, 1947

By Thomas M. Barczak, Christopher Mark

Roof supports can only be understood in conjunction with the rock structure that they support. The strength of the rock depends on geology, and the loads are applied primarily by the in situ and mining-induced stresses. Other factors, such as wider spans and retreat or multiple-seam mining, can also reduce the stability of mine openings. Roof supports are used to help stabilize these openings, but their performance characteristics must be properly matched to the loading environment and ground behavior if they are to succeed. Roof supports include both intrinsic supports, such as roof bolts, and standing supports. The key characteristics of any support include its maximum load-carrying capacity, stiffness, and residual strength. Other important factors are the timing of installation, the stability of the support as it is loaded, and the capability of the support system to provide skin control. This paper explains in practical terms how supports work and the important factors in ensuring that a good support design and application strategy are developed.

Jan 10, 2000

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By C. E. Jordan

Domestic cobalt resources are relatively large, but low grade. The full potential for cobalt production from domestic sources is at least 19.4 million lb of cobalt per year exclusive of offshore resources. A summary of the cobalt processing technologies for the major domestic resources is presented in this Bureau of Mines report. The processing technologies for the Blackbird, Madison Nine, Duluth Gabbro, iron ore pyrite, laterites, and manganese sea nodules are nearly complete, but the economics are not favorable. Research on these resources should be limited to approaches that promise to cut the total processing costs by at least 50 pct. The most promising sources of cobalt are the spent copper leach solutions and siegenite from the Missouri lead ores. Research on cobalt processing from these two sources needs to be completed.

Jan 1, 1988

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.2 The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; 1960, 5.3 feet; and 1965, 5.2 feet.3 Table 1 includes data on number and production of bituminous coal and lignite mines classified by 1-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, 1960, and 1965. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness--less than 2 feet to more than 50 feet--a large majority of the production, 62 percent in 1965, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1967

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By Mark I. Copeland

Bureau of Mines researchers investigated the combined effect of copper and tin additions on the mechanical properties of hot-rolled steels. Wrought steels containing 0.2 wt-pct C and up to 0.2 and 1.0 wt-pct Sn and Cu, respectively, were made and evaluated by conducting tensile and impact tests and electron-beam microprobe and electron microscopy examination. Tin additions did not significantly affect the tensile properties of steel at different copper contents in the hot-rolled condition. Tin lowered the copper content at which strengthening by copper precipitation normally starts, 0.8 wt-pct, and decreased the strength of steel aged at 1,022° F (550° C). The most adverse effect of tin was lowering the notch toughness of steels at most copper contents.

Jan 1, 1976

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By Jos. R. Guiteras

This paper is one of a series describing; mining and milling methods and costs being published by the Bureau of Mines. It deals with the mineral resources of western South Dakota and describes the mining and milling of tantalite and associated amblygonite by the Black Hills Tin Co. and the Fansteel Mining Corporation. ACKNOWLEDMENTS Acknowledgment is made to Earl C. Schultz and Arthur I. Johnson, respectively superintendent and engineer for both the Black Hills Tin Co. and the Fansteel Mining Corporation, who contributed the information on mining and milling operations.

Jan 1, 1939

By Wallace E. Anable

This investigation by the Bureau of Mines was conducted chiefly on Cuban serpentine nickeliferous ores to determine whether these materials would be amenable to direct carbothermic reduction in an electric furnace to produce a low-carbon ferro-nickel. The project was carried out as one of several under a Memorandum of Agreement between the Bureau of Mines and the General Services Administration (Contract GS-OO-B (D)-152l). Two ore samples were received for this investigation. One was a mixture of nickeliferous serpentine from the North Ocujal, South Ocujal, and San Juan claims of the Nicaro Nickel Co. The other sample was a mixture of material from the Ramona and the Lorna Mulo claims of the Cuban Nickel Co. Most of the ore from the Ocujal-San Juan deposits and about 40 percent of the sample from the Ramona-Lorna Mulo deposits were calcined before smelting. The remainder of the sample from the Ramona-Loma Mulo deposits was smelted after drying to about 8 percent moisture. An arc-resistance, selective-reduction smelting technique was employed in these tests. Either bagasse alone or a mixture of bagasse and coke was used for reductants. No flux was used in the furnace charges.

Jan 1, 1957

By Oliver C. Fursman

This work was conducted to determine the feasibility of producing aluminum-silicon alloys in a pit-type, three-phase electric-arc furnace. Two carbon-lined furnaces were used in the tests. The power input ranged from 120 to 240 kw. in the small furnace and from 420 to 460 kw. in the large furnace. Energy consumption ranged from 5.3 to 11.5 kw.-hr. per pound of alloy produced and electrode consumption, from 240 to 510 pounds per ton of alloy produced. A wide range of crude aluminum-silicon alloys was produced by direct smelting of clays or similar aluminum silicate raw materials, using hogged fuel or wood chips as the major source of carbon in the furnace charge, and silicon of high grade was produced by smelting quartz. The aluminum content of the aluminum-silicon alloys ranged from 15 to 55 percent. Alloys produced from a white opaline-silicate clay were relatively free of iron, titanium, and other impurities. Those produced from western fire clays and kyanite, although richer in aluminum, contained considerable amounts of impurities. The purity of the alloys depended largely on the composition of the raw materials.

Jan 1, 1960

After more than 20 years dependence on bituminous coal as a primary fuel for generating electricity, the Pennsylvania Power and Light Company initiated a one-year study on the economics of building an electric generating station using anthracite as a fuel. The study will be completed in December 1976. If the feasibility study so indicates, PP&L will consider installing four 400,000 kilowatt generating units for scheduled commercial operation in 1985. Each unit would consume up to one million tons of anthracite annually. Anthracite generally is more difficult and expensive to extract than bituminous coal, but it has a significantly lower sulfur content than the bituminous coal currently being used by PP&L, thereby eliminating the costs of installing sulfur emission controls at generating stations. Moreover, significant reductions in transportation costs may be realized because the utility's operating territory is situated in the center of the anthracite region in northeastern Pennsylvania. These advantages may indicate that the use of anthracite is more economical than bituminous coal to PP&L. ASBESTOS -Asbestos production in the U.S. dropped again in 1975 until it was just two-thirds of that in 1973. This was in spite of the very strong demand caused by the Quebec strike. The 7-month strike of the asbestos miners in Thetford Mines, Quebec cut off 55 percent of the normal supply of U.S. consumers. Apparent domestic consumption was less than 75 percent of that in 1974. The wage settlement will probably result in a 20 percent increase in asbestos prices.

Jan 1, 1975

By R. E. Morgan

[IN COMPILING the table of analyses of this bulletin every available source of information was studied. These sources, as listed at the end of the table, were many and varied, and it believed that the tabulation gives the best general information obtainable. However, its known accuracy and completeness of coverage necessarily fall far short of published data on coals of the United States. A table of world production of coal and lignite, as and published by the Bureau of Mine, of world resources of coals, brown coal, and lignite, as published in the Yearbook of the World Power Conference, 1948, are included for convenience of the reader. The six continental maps at the end of the bulletin show the general location of the principal coal fields.]

Jan 1, 1952

By H. V. Makar

The Bureau of Mines successfully demonstrated, on a pilot plant scale, a sodium sulfate (Na2S04) refining process for removal of copper from molten ferrous scrap. Previous tests established technical feasibility on a bench scale for achieving low copper concentrations and determining the principal factors controlling process efficiency. The pilot plant study involved a 1-ton arc furnace for melting ferrous scrap and a 1-1/2-ton treatment ladle. Results of these tests showed that copper removals obtained in laboratory tests (approximately 40 relative percent copper removal with 10 weight-percent surface addition of sodium sulfate) could be achieved on the pilot plant scale when excess carbon was added with the sodium sulfate compacts. Data were obtained on temperature losses and carbon consumption related to Na2SO4 treatment.

Jan 1, 1974