Search Documents

By S. H. Ash

THE MAGNITUDE of the drainage problem of the anthracite industry in Pennsylvania's Western Middle field is realized when it is known that in 1951 nine pumping plants in this field pumped nearly 36 billion gallons of water to the surface. This is almost 68,000 gallons per minute pumped against an average hydrostatic head of 350 feet for that year alone. In 1948 over 20,000 gallons per minute was pumped by relay pumps against an average hydrostatic head of 265 feet. In addition to the water pumped to the surface, it is estimated that 15,000 gallons per minute overflows to the surface from underground pools in idle mines. The volume (second-feet) of water pumped and overflow water is almost 1;z times the, average mean flow of the Schuylkill River at Pottsville for the 8-year period 1944--51 (7, 13).4 Mahanov and Shamokin Creeks drain an area of 99 square miles in the Western Middle field, and all surface drainage in this area must traverse some part, of the coal measures before entering these streams. On the basis of 46.03 inches of rainfall (the weighted average of 6 recording stations for 1948), the runoff from the drainage area during that period was 51 billion gallons, approximately 1 times the volume of water pumped by all mine-pumping plants in the Western Middle field. In other words, because of the pervious strata overlying the mine workings, approximately two-thirds of the total runoff in the drainage, area becomes mine water tributary to the pumping plants.

Jan 1, 1953

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By D. S. Kingery

This study describes five fatal accidents so unusual in occurrence that the chain of circumstances bringing them about may never be duplicated. The intent of this publication is to illustrate that everyone working underground is subjected, at all times, to definite inherent mining hazards and that safety devices, though provided, often are ineffective or not used. It is hoped that a study of these fatal accidents in bituminous-coal mines will show workers and safety engineers that nothing can be taken for granted. Safety planning with continuous study can prevent these unusual accidents as well as the routine recurring types, which cause the majority of coal-mining injuries. The treacherous, fatalistic philosophy that "it can't happen to me" or that "when my time's up I'll get it regardless of what I do," still prevails among individuals and even safety engineers. The individual or safety man who believes in luck as applied to safety should not read any further, since this study was written for the sincere, safety-minded individual who accepts the prevention of all accidents as a challenge to his knowledge, initiative, persuasiveness, and salesmanship.

Jan 1, 1954

By A. B. Hooker

A list of permissible mine equipment, tested and approved by the Bureau r. Mines previous to January l, i-)4, , was published in Bureau c Moines In ornation Circular 7207.3/ The l ,.t c -. that dote was complete as to equipmentthen available and in current Information Circular 7210,?+/ published as a supplement thereto, listed equipment approved during; the calendar 1942. Information Circular72x'3,_/ published as a second supplement thereto, ! listed equipment approved during the calendar year 1943. The present listis. Another supplement covering approvals issued during the calendar year 1c)44. The items are numbered crud to indicate the consecutive order in which each typo of machine or device was approved _.c?. in its particular classification. Thus Information Circular 7207 gave 1,t drills and drilling much fines on the Bureau'sactive.. d active list Ih: additional anal approval: were given in 1942 the three issued in 19 and one issued :n 1944- bring the total to `3. Item 111, under. Loading Machines and conveying appeared in lnformation Circular 7207. It is repeated ',tore to _how that on j,,l was granted Curia 1the optional of this loader when modified .'or 2 0. alt ciruits .]

Jan 1, 1945

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By E. J. Matson

From February until July 1943 the Bureau of Mines conducted an exploration project at the Majuba Hill mine to determine tonnage aria grade of the copper and tin ore and to search for extension of the mineralization. The work comprised sampling, long-hole drilling, underground excavation, and ore-dressing test.

Jan 1, 1948

By G. W. Jones

Among its investigations into the prevention of waste in production and use of oil and gas, the Bureau of dines has made considerable study of the efficient utilization of gasoline and by-product distillates in motors, this being done chiefly by measuring and analyzing the exhaust gases therefrom. A number of reports3 of a highly practical nature have been published and are available on this subject. The results of these tests have shown that the average motor vehicle wastes approximately 30 per cent of the heat value of the fuel used, as incomplete combustion products - carbon monoxide, hydrogen, and methane, These unnecessary large heat losses are mainly due to improper carburetor adjustment, and by proper¬ly adjusting the carburetors for maximum power and efficiency a large part of this heat loss can be eliminated. This in turn results in an increased mileage per gallon of fuel used.4

Jan 1, 1924

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

By A. C. Richardson

During the past two and a half years the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive study of coal preparation in the State of Alabama. Considerable time has been devoted to the study of the washing characteristics of the Mary Lee bed and the various methods used in preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery Of the Republic Steel Corporation, Sayreton, Ala.

Jan 1, 1931

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By William B. Harper

Domestic sales of carbon black sustained the upward movement for the 4th consecutive year, reflecting the increased sales of motor vehicles during the same period. Sales of carbon black in the domestic market topped 2 billion pounds for the first time during 1965 and have more than doubled the output of 20 years earlier. By far the largest user of carbon black is the rubber industry. That use accounted for more than 94 percent of the carbon black consumption with the bulk of it being used in tire casings and tubes. Thus demand for carbon black is naturally sensitive to trends in the sales of passenger cars and other motor vehicles, Manufacturers of inks, paints, plastics, paper chemicals, and food are also important users of carbon black.

Jan 1, 1967

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By John R. Shattuck

The Shasta and California Iron-ore deposits are 14 miles northeast of Redding, Shasta County, Calif.; and since 1907 have produced more than 300,000 short tons of exceptionally pure iron ore. Although some ore was mined and smelted from 1907 through the First. World War, most of it has been produced from 1942 through 1945 for use in making heavy ship ballast and concrete anchorages for mines. Irregular masses of magnetite, ranging from lumps of a few tons to pods containing about 25,000 tons, occur associated with skarn near the contact between the McCloud limestone and a younger granitic intrusive. Some of the deposits are low-grade, whereas others are nearly pure magnetite. Selective mining and hand sorting are necessary to produce a high-grade product. Investigation of these deposits by the Bureau of Mines included 2,910 feet of diamond drilling, some surface sampling of the principal mineralized zone and beneficiation tests. Resulting factual data are given in the body of this report.

Jan 1, 1948

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By R. L. Rough

The Bureau of Mines analyzed rotary-coring-operations data to compare mud and air as coring mediums, and to compare core recoveries, penetration rates, and cost data for the respective mediums as part of an investigation of the susceptibility to secondary-recovery techniques of petroleum reservoirs in Ohio, Pennsylvania, and West Virginia. This report describes the rotary-diamond coring equipment and operations employed while coring 20 wells--10 cored using mud, and 10 cored using air. Data relevant to the draw works, rotary-table power, drill pipe, drill collars, core barrel, core head, mud pumps, or air compressors are tabulated. Average bit weight and rotary speed, core recovery, and penetration rates are listed for each formation cored. In general, core recoveries were better from the mud-cored wells, whereas penetration rates were faster for the air-cored wells. Coring costs were about the same for single-formation wells cored with either mud or air; however, costs increased considerably when multiple-formation wells were cored with air.

Jan 1, 1969

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973