Search Documents

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By Seth T. Reese

REPORTS received from operating companies by the Bureau of Mines, United States Department of the Interior, indicated marked progress in the reduction of injuries to employees in the coking industry in 1951 as compared with 1950. The fatality rate (0.14) per million man-hours of exposure declined 33 percent and was the second best performance since statistics on the industry were first collected in 1916. The nonfatal-injury rate (10.94), the best since 1940, declined 8 percent and was bettered only in 8 of the past 36 years. The nonfatal rate is based on all injuries resulting in loss of time for more than the remainder of the day on which the injury occurred. The exposure to hazard, as represented by the number of man-hours of work time during the year, was 7 percent higher than in 1950 and, except for the year 1943, was the highest since 1920. The fatality rate for men employed at beehive-coke ovens decreased 16 percent and the nonfatal-injury rate 23 percent, while the man-hours of work time or exposure increased slightly over 16 percent. The fatality and nonfatal-injury rates at byproduct ovens declined 33 and 2 ½ percent, respectively, while the number of man-hours worked increased 6 percent.

Jan 1, 1954

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By Charles J. Haas

The objective of this research was to investigate the interaction phenomena of rock and types of rock bolts to develop design principals for using grouted roof bolts. The investigation was to determine the effectiveness of grouted bolts in resisting lateral displacement and axial separation along fracture planes, and also to determine if grouted bolts eliminate the axial tensile stress near the anchor and the resulting rock fracture. The first year's effort involved defining the post-tensioning response of grouted bars and determining the amount of shear resistance generated by conventional and resin-grouted bolts. A finite-element analysis showed that if the rock and resin grout behave in an elastic manner, the post tensioning of a grouted bar will affect mine roof stability only if movement occurs near the collar. An experimental shear test program revealed that both conventional bolts and resin-grouted reinforcing bars significantly increase shear resistance along fracture or bedding plane when the average normal compressive stress on that plane is low (in the order of 25 psi) and when the bolt is oriented so that the shear displacement tends to lengthen the bolt. An increase in shear resistance is also noted at the higher normal pressure of 250 psi; however, the increase is small compared to the corresponding shear resistance without a bolt. Conventional bolts oriented so that they tended to loosen with shear displacement added no significant shear resistance.

Jan 1, 1974

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By Robert L. Kranz

The U.S. Bureau of Mines (USBM) has been monitoring and studying seismic activity associated with mining in the Coeur d'Alene silver district of northern Idaho. New statistical methods of studying the stope-scale (1-to l00-m) seismicity at one Idaho silver mine are used in this report (part 1) and its companion (part 2). This report deals with methodology and its limitations. The recent concept of fractals and their seismological use is discussed and applied to mining-induced seismicity. Three types of fractal studies are addressed: spatial analyses (including temporal changes of spatial patterns), temporal analyses, and size analyses. Other statistical measures of mine seismicity are also addressed: event mean location, inter-event distance distribution skewness, temporal coefficient of variation, nearest neighbor and next event statistics, and event location planarity patterns. Each of the methodologies discussed (fractal and nonfractal) is presented using sample data from two stopes in the mine. It is shown that stope-scale, mining-associated microseismicity has a fractal nature. The usefulness of demonstrating fractality (scale invariance) for predictive or descriptive purposes depends on recognition of the factors affecting the calculation of fractal dimensions. Several methodological traps are illustrated that can lead to an incorrect conclusion.

Jan 1, 2010

By C. Lorimer Colburn, Spencer P. Howell

"Numerous accidents are still being reported that have resulted from the delayed explosions in drill holes. Some of these accidents have boon due to retarded burning of the fuse, causing the charge to explode after the miners had returned to the face, but the majority have been caused by the minors drilling or picking into unexploded explosives, either in unexploded bolas or in broken rock. Although the industry has been cautioned by the Bureau of Mines, manufacturers of explosives, and other agencies regarding the care that is necessary in the handling of explosives, yet reports of these accidents are still being received and many of the accidents are fatal, They occur in spite of the best efforts of the mine officials and men, but many of those that have been reported could have been avoided if the following precautions had been observed:Misfires should not be approached even for the purpose of inspection until three hours have elapsed if fuse was used, and ten minutes if electric detonators or electric igniters were used. These are minimum recommendations. It would be preferable to allow a longer time, for fuses have been known to hang fire for twelve hours."

Aug 1, 1920

This report is the 21st in a series summarizing research and technologic work on coal and related investigations by the Federal Bureau of Mines - the Chard of the series published on a calendar-year basis 2/ Subject publica¬tions of the Bureau during 1956 are cited, and pertinent Bureau work is described briefly. The most effective method of conserving our important coal reserves is through improved technology of production and utilization. Associated problems form the program of the Bureau.3 4 5 6/ Potential production is depend¬ent on a knowledge of the quantity and quality of the reserves, and the Bureau continues to contribute information on this subject. Many problems are being studied that relate to improvements in current production, including mining methods and health and safety measures. Preparation of mined coal is necessary for its most efficient utilization. Preparation by conventional methods is being studied, as well as the development or new methods. Fundamental studies on the structure and properties of coal are necessary to insure full advantage of the special qualities of different coals. Controlling factors in the efficient use of coal in combustion, carbonization, gasification, and direct and indirect hydrogenation of coal are being studied continuously, and new processes are being investigated. The many advances in all these fields are discussed.

Jan 1, 1959

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970