Search Documents

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By E. L. Fosse, W. S. Wright

"INTRODUCTION Preliminary and detailed exploratory examinations of iron and copper ores on Prince of Wales Island have been conducted by the Bureau of Mines from early in 1942 until the end of 1944. Among these investigations was that of the Jumbo magnetite deposit, which was visited by Stephen P. Holt, an engineer of the Bureau of Mines, during a preliminary examination of the Copper Mountain and Jumbo properties September 15 to 18, 1943, During the months of June, July, and August 1944, a more detailed examination, which consisted essentially of mapping and sampling, was made by the authors working in conjunction with George C. Kennedy of the Geological Survey, Geological, topographical, and dip-needle contour maps were made of the area, and 97 channel samples were cut.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes sam¬ples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is made to R. D. Stewart, Territorial Commissioner of Mines and former general manager, and to Duncan Campbell, Ketchikan, Alaska, former mine superintendent of the Jumbo mine. Acknowledgment is also due to George C. Kennedy of the Federal Geological Survey for extending cooperative assistance in topographical mapping, dip-needle surveying, and geological study of the deposits. Further acknowledgment is made to C. Travis Anderson, chief, Rolla Division, Metallurgical Branch, and other members of that division for conducting beneficiation tests on Jumbo Basin ores."

Oct 1, 1946

By John D. Spencer

Projects aimed at achieving the least disturbance to the Nation's air, water, and land resources in the mining and utilization of coal continued to be a feature of the Bureau of Mines coal program. This reflects the current concern about damage inflicted on the environment by our growing and increasingly affluent society. Mine Health and Safety research, along with investigations related to all other aspects of coal extraction and use, also continued to be implemented and expanded.

Jan 1, 1970

By A. W. Deurbrouck

This report describes the washability characteristics of 18 coal samples taken from 11 drill hole cores from the San Juan Basin area of New Mexico and Colorado. The ash content of these coals could generally be substantially reduced by removing the heavy impurities. The coals were characteristically low in sulfur content; only one sample contained more than 1 percent sulfur after removing the sink-I.50 specific gravity material. The coals ranged in rank from subbituminous C to high volatile C; 11 of the samples were subbituminous A. Many of these core samples came from areas where very little fieldwork has been done; consequently, an outgrowth of this work has been an increase in known coal reserves of the San Juan Basin area.

Jan 1, 1972

By P. A. Wasson

Drill cores from 15 holes in the West Central Mesabi Range were studied as part of the Lake Superior iron resource investigation begun in 1957 by the Bureau of Mines. Chemical, petrographic, and metallurgical analyses were made to determine grade, mineralogy, magnetic characteristics, and response to beneficiation. Data in this report were developed to provide a better under-standing of the nature and character of low-grade iron ore occurrences, to measure potential of usable ore, and to provide a basis for comparison with bank samples previously taken in the same general area. The average iron content of 4,445 feet of core was 31.8 percent. Iron oxides present were hematite, goethite, and magnetite; the gangue minerals were chiefly quartz, iron silicate, and iron-bearing carbonates.

Jan 1, 1962

By A. T. Iannacchione

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. 'Wants' in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By John W. Adams

The present status of the National Bureau of Standards program is that many magnetic tapes of analog data have been recorded in four major mines. Each mine uses different types of equipment. In addition, some surface measurements of noise have been made at two additional mines. Two types of recordings have been made: (1) broadband measurements for spectral plots and (2) narrowband measurements for amplitude probability density (APD) plots. Only data from one mine (Robena #4) has been processed and was, presented at this workshop. The short-term goals are: (1) finish processing data from the other mines, (2) establish or reduce measurement system uncertainties, (3) put Robella report into final form for distribution, and (4) hold a review to determine what has been done, to distribute and to interpret the preliminary data, and to determine what still needs to be done. Long-term goals are: (1) complete final reports on each of the mine trips, (2) establish techniques for predicting noise in mines already visited and establish uncertainty bounds for these predictions, and (3) establish techniques for predicting noise in mines that have not been visited (but that use similar equipment to those visited) and also establish uncertainty bounds for these predictions. Specific factors or formats to be presented include: (A) For underground broadband measurements: 1. 300 Hz to 100 kHz spectral plots 2. 300 Hz to 384 kHz spectral plots 3. 300 Hz to 192 kHz spectral plots 4. 300 Hz to 6kHz (subject to change to 3 or 12 kHz) spectral plots (B) For surface broadband measurements: 1. 300 Hz to 6 kHz (or 12 kHz) spectral plots 2. 300 Hz to 3 kHz spectral plots (C) For underground narrowband measurements : 1. APD plots at 12 frequencies from 10 kHz to 32 mHz of magnetic field strength 2. R. M.S. and average values will be calculated based on time averaging for these plots (D) Sample spectral measurements of: 1. Roof-bolt voltages 2. Trolley wire-to-rail voltages 3. Phone line currents

Jan 1, 1973

By E. L. Garton

[Analyses of may crude oils produced in Louisiana are included in reports that t have boon published by the Bureau of Mines. The first report, giving, analyse of 6 Louisiana crude oils, was 3 published in 1921 and this was followed a year later by Report of Investigations 2416,4/ giving 7 additional analyses. The eleven most important of these analyses were incorporated in Bulletin 291.5/ issued in 1928 In 1934 analyses of 26 crude oils produced in southern Louisiana were published.6/ The percent report presents analyses of 72 additional samples of crude oil from 45 fields in 23 parishes In Louisiana.]

Jan 1, 1939

By Margaret R. Egan

A study of the combustion emission products of rigid ventilation ducting was completed by the U.S. Bureau of Mines. The ducting was composed of fiberglass-reinforced polyester resin. Four properties of the ducting were evaluated: (1) propensity to ignite, (2) smoke characteristics, (3) gas emissions, and (4) heat release. Particle sizes, obscuration, optical densities, and production constants for gas and smoke were also calculated. These results provide comprehensive data about the emission products, detectability, and relative hazards of fiberglass-reinforced plastic ducting and other mine combustibles under realistic fire conditions.

Jan 1, 1990

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

By Jerry E. Olson

In 1985 the U.S. Bureau of Mines conducted a mineral survey of 68,458 acres of the Clan Alpine Mountains Wilderness Study Area (NV-030-102) which covers 196,128 acres in Churchill County, NV. Most of the area studied is underlain by Tertiary volcanic rocks. In the northeast corner of the study area, an upthrown block of Triassic sedimentary rocks partially extends into the area. The study area is probably part of a large eroded caldera. No major mines or active claims are within the study area. Field investigations included examination of workings in Starr Canyon, historical and recent mining activity near the mouth of Florence Canyon, other mining claims, and anomalous zones delineated by data from Great Basin GEM Joint Venture studies. No mineral resources were identified, but sample results indicate one significant mineralized zone situated along a northwest trend between the head of Starr Canyon and the head of Cherry Creek may contain precious metal resources. Further investigation of this zone is warranted.

Jan 1, 1987

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944