Search Documents

By Robert M. Strong

The following report is a summary of the commercial results which 'Were obtained from 2,000 tests conducted by the technologic branch of the United States Geological Survey at St. Louis, Mo., and Norfolk, Va., in 1907 and 1908, under the technical supervision of R. H. Fernald, engineer in charge of the producer-gas section. The tests dealt primarily with gasoline, forming part of the investigation of mineral fuels provided for by acts of Congress. To determine the relative economy and efficiency of gasoline it was compared with denatured alcohol. The tests, many of which were undertaken in connection with work for the Navy Department, supplemented, to a certain extent, the work of previous investigations, but only so far as was necessary to emphasize some of the more important points and to lead up to the defining of conditions required for the economical use of gasoline and alcohol. In order to determine and eliminate the affecting engine conditions as far as possible, the investigation was commenced by making comparative gasoline and alcohol tests on the same engines. These tests were repeated on other engines of approxiElately the same size and speed, having different degrees of comFression, different methods of governing, and different carburetors. The final report will include much material that may be of use in engine design, but that side of the investigation was not pursued any further than was necessary to obtain the best possible results, for alcohol and for gasoline with the engines at hand, and to prove that the minimum fu·el-consumption rate for each could be obtained in approximately the same manner. The effects of engine and of operating conditions both have a bearing on the commercial deductions but will be discussed only in a general way at this time.

Jan 1, 1911

By Michael F. Dunn

Since crushing of rock to a smaller size is an integral part of almost any mining and quarrying operation, a study was carried out to identify and develop improved techniques for alleviating a major cause of accidents and work stoppages arising when an oversize luck or boulder lodges in the throat of the crusher. The configurations and operations of various crusher types is described, sources of boulders in the mining operation, and a detailed review is made of mining, quarrying, and construction regulations for all states, Canada, and the Federal Government for applicable provisions. Representative mines were visited and other operations contacted for their boulder handling techniques where it was found that blasting techniques used included mudcapping, bombs, and blockholing, often done very crudely and inefficiently with poor practices and various mechanical systems were used such is hooks of, overhead cranes, impact hammers, and grapplers. Safety analyses of all methods pointed out the hazards associated with blasting in the open and the dangers of entering a crusher. Boulder blasting can be done in a safer fashion if a planned step-by-step procedure is followed, and inherently safer blasting products such as exploding bridge wire blasting caps and improved blockholing techniques. In general, though, the installation of a suitable mechanical system such as an impact breaker will prove safer and cost effective even in a smaller mine or quarry.

Jan 1, 1981

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

By Ivor Hawkes

The purpose of the development described in this report and as stated in the contract work statement is to "design, develop, fabricate, test and demonstrate, and deliver to the government permissible low cost cylindrical stress gauges and associated components capable of measuring change of stress as a function of time in underground coal mines. The cylindrical stress gauges shall be suitable for installation in bore holes". The technique adopted for measuring rock stress changes is to preload a steel cylinder diametrically across the sides of a 1-1/2 in diameter bore hole and detect deformation of the cylinder from stress changes in the rock, by means of a vibrating wire transducer. By calibration, changes in the period (time for one wire oscillation at the natural frequency) of a high tensioned wire stretched diametrically across the cylinder in the direction of load application are related to stress changes in the rock. To completely evaluate the stress field change in the plane of the bore hole, three gauges set at an angle to each other are required.

Jan 1, 1973

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps.

Jan 1, 1964

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

By Ben E. Lindsly

The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2 Lewis3 states, "The estimate of 80 to 90 per cent of the oil left underground does not seem incredible."

Jan 1, 1926

By Herman W. Sheffer

This report describes and discusses present-day leaching technology employed to recover copper from low-grade mine and dump materials derived from the exploitation of copper ore deposits in the Western United States. Illustrations of the integral parts of the leaching, precipitation, and recovery operations at several copper-producing companies are presented. Schematic drawings are included to present typical flowsheets of leaching and precipitation operations. Operational problems common to most copper leaching and precipitation plants are discussed. Areas of present and future research to improve leaching techniques are cited.

Jan 1, 1968

By Albert E. Schreck

[THE COMPOUNDS of strontium were confused with those of barium until 1790, when A. Crawford discovered that the mineral strontianite, long believed to be a barium mineral, was a compound of a new element. This discovery was confirmed 2 years later by I. C. Hope. The mineral was named strontianite because it was found near the town of Strontian in Argyllshire, Scotland. In 1808 Sir Humphrey Davy isolated strontium metal by the electrolysis of fused chlorides. Celestite (strontium sulfate) and strontianite (strontium carbonate) are the principal strontium minerals. Because of its more widespread occurrence, celestite is more important commercially.]

Jan 1, 1959

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

By A. C. Fieldner

All technical facilities of the Bureau of Mines have been geared for more efficient use and conservation of mining equipment, developing plans for safety, improving the quality of coal through better methods of preparation, studying the problems of coal storage and utilization, and extending the uses of coal5/ for the war and postwar economy. The Bureau is now analyzing all of the coal purchased by the Army and much of that required by the Navy. Work on boiler feed water was doubled over last year to meet the increased demand made by the War Department for protecting vital boiler plants in many new camps and defense plants. Progress has been made in safely storing coal to reduce dangers of spontaneous ignition to a minimum and to preserve coking power. Mixtures of oil and coal to be used as a substitute fuel have been investigated. Technical service on the conversion of plants to other fuels has been given to government agencies and private consumers. The possibilities of making motor fuel,

Jan 1, 1944

By D. G. Foot

The Bureau of Mines investigated two methods for recovering potash from carnallite ore in continuous 100-lb/h flotation units. In the insoluble-slimes flotation procedure, insoluble slimes were removed by flotation prior to potash flotation. In the direct flotation method, insoluble slimes were depressed and the potash floated directly without prior removal of the insoluble slimes. Seventy-three percent of the potash in the ore was recovered in a leached final KCl product contain-ing 59.1 pet K20 using the insoluble-slimes flotation method. The direct flotation method recovered 74.5 pct of the potash in a final product containing 60.2 pet K20. The rate of return on the investment was calculated at 13 pct for the insoluble-slimes flotation method and 15 pct for the direct flotation method, based on a Bureau economic evaluation.

Jan 1, 1984

By Alan A. Campoli

The U.S. Bureau of Mines conducted research to characterize longwall gob loading under bump-prone geologic conditions. Bureau-designed stress meters were installed in the floor rock beneath two longwall panels and coal pillars in the gate road between them. Gob and gate road pillar stress was monitored continuously by a state-of-the-art data acquisition system. The timing of the final destruction of the abutment pillar's load-bearing core was optimal, since the pillar is located between two gob areas and no longer of significant importance for ground control. Maximum stress was observed immediately in front of the longwall face, and this pressure quickly dropped as the face moved past the instruments. The center of the longwall panels regained significant overburden load, while the instruments located less than 100 ft from the edge of the panel showed little or no increase in pressure due to gob reloading.

Jan 1, 2010

By Wilbert J. Huff

The organization of the'Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely and accurately many previously published limits.

Jan 1, 1938

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By S. Vennos

As a result of Synopsis 73-16 Dynadyne responded with an unsolicited proposal offering the Bureau of Mines to develop an ultra-low volume coal mine dust personal sampler. In the ensuing technical discussions the choice of a desirable volumetric rate became a focal point. While, the initial proposal was based on a volumetric rate in the area of 50 cc/min the Government expressed interest in a variety of mass flow rates ranging from 50 cc/min to 2000 cc/min. The physical characteristics such as weight, volume and configuration of a personal sampler are to a large extent - dependent on the operating volumetric rate. It became readily apparent that the optimum size of such an instrument as a function of volumetric rate was not known and that a study of the choice of optima was essential prior to beginning the development, Hence, the Government authorized a two phase approach to this project. Phase I was to include a Technical Evaluation Study of optimum characteristics in the range between 0. 1 to 2. 0 lpm. Based on these findings and in consultation with MESA personnel, the Bureau of Mines was to authorize the second phase that is, the development. Phase II, was to include the drawing of a set of performance specifications stating among others the desired operating volumetric rate. In this report, every effort was made not only to present the actual work done over the course of this development, but to reflect also our engineering "thinking" providing answers as to the "why" we preferred certain solutions over others. We believe that this added dimension is not only useful for the Government official evaluating this report, but also that the Government is entitled to it providing the official with an educational content useful in avoiding future costly repetitions of similar situations.

Jan 1, 1975