Search Documents

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

By Martin D. Conyac

Results of the minerals survey indicate low potential for the discovery of placer gold along Deck Creek aid for copper, silver, and gold in PreTertiary rocks within the boundaries of the Lake Fork RARE II area. Potential for oil, natural gas, coal, and geothermal resources is negligible. No evidence of economic mineral resources was found during the examination of the study area, and no assays of rock or placer samples taken from the urea showed economic mineral values. There are no producing or developing mines within the boundaries o of the lake Fork study area. SETTING Mining Districts The Lake Fork RARE II area is on the eastern fringe of the Cornucopia Mining District, which is centered about 6 mi west. It is also on the western edge of the Homestead district, centered about mi east.

Jan 1, 1983

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By W. L. Dare

This publication is one of a series prepared by the Federal Bureau of Mines on methods and costs of producing uranium ore on the Colorado Plateau. The information it contains was gathered in 1955-58 and applies to eight small operations. (See fig. 1.) Mining costs have increased since the data were I collected, but the information should be helpful in estimating future costs I at similar deposits. The Bureau of Mines had early experience in the production of carnotite-type ores on the Colorado Plateau.3 4/ Under a cooperative agreement with the National Radium Institute in 1914-16, the Bureau mined and concentrated carnotite ore for recovery of radium, uranium, and vanadium. The ore was taken from claims in or near Long Park Montrose County, Colo., about 3 mi. south of La Salle Mining Co.'s La Salle mine, which is one of the mines described in this report. The Bureau leased the claims from Crucible Steel Mining & Milling Co., a subsidiary of Crucible Steel Co. of America, and from 1914 to 1916 produced 990 tons of high-grade ore, containing 2.6 pct. U308, and about 2,000 tons of mill-grade ore, containing 0.85 pct. U308. The high-grade ore was shipped directly to a radium-recovery plant built in Denver in 1914 under the cooperative agreement. There, commercial methods of extracting uranium, vanadium, and radium from carnotite ores were developed by Bureau personnel. The lower grade ore was concentrated at a small mill in Long Park before being shipped to Denver. The final recovery was 69,000 lb. of U308 and 8.8 g. of radium. The direct mining cost of producing the high-grade ore, including the labor to hand sort and sack it, was $35.96 per ton. Freighting the ore 58 miles to Placerville, Colo., the nearest rail point on the Rio Grande Southern Railway, cost $25.28 per ton, which included $4.55 per ton for ore bags and twine. Four-or six-horse teams pulled two wagons in tandem and made the

Jan 1, 1961

By V. A. Danielson

The Bureau of Mines examined sources, consumption, and movement of iron and steel scrap in the southeastern States--Alabama, Florida, Georgia, Kentucky, North Carolina, South Carolina, and Tennessee. Officials of the scrap-processing and scrap-consuming industries were interviewed, data was obtained from the published literature, and a canvass was made by the Bureau of scrap consumers. The Southeast generated excess scrap which was shipped to domestic and foreign consumers in about equal proportion. Total 1963 demand in the Southeast was 3,336,000 net tons, of which purchased scrap was 75 percent, foreign exports 13 percent, and domestic exports 12 percent. Alabama, with 47 percent of the purchased scrap consumption in 1963, was the most important scrap-consuming State, and Kentucky, with 34 percent, was the second most important one. Southeast demand was 4.8 per-cent of the total U.S. demand. Projected 1980 consumption is 8,340,000 tons. Scrap prices showed a slight downward trend for the period 1953-63, although gross consumption increased slightly. A significant trend in processing scrap in the Southeast is the preparation of smaller bundles or "briquettes" weighing from 75 to 150 pounds, which are easier for consumers to handle and inspect. Another significant development is the "shredding" of automobile scrap which produces a dense, clean scrap especially desirable for use in electric furnaces.

Jan 1, 1967

By Oliver Bowles

[Simple systematic accounting that adequately records all transactions has long been regarded as essential to the welfare of any business enterprise. Some of the defects that detract from the prosperity of the slate industry are attributable to a lack of effectiveness in cost keeping. This condition has promoted the United States Bureau of Mines to make a detailed study of accounting methods for the slate industry, and to present for consideration a system of accounts, which it is believe would enable the industry to attain more economical management and operation if accepted by a fair proportion of its important units. The method of accounting presented herein has been worked out with the assistance of leading slate producers and the recommendations are tentative and are submitted in this form as a means of developing constructive criticism. Believing that cooperative effort in this, as in many ether problems will bring the most enduring benefits to the industry as a whole, the writer urges that the cost earnest consideration be given to this vital problem now facing the slate industry.]

Jan 1, 1929

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By D. Harrington

"Coal—mine explosions are accidents that can and should be prevented. In former years hundreds of lives were lost each year in the United States as a result of such explosions, but after 1932 the numerous precautionary measures adopted had reduced their frequency and severity 75 percent or more until in 1940 several very disastrous explosions marred the good record. Unfortunately, both the number and severity of explosions seem to be tending to increase compared with the relatively good achievement from 1933 to 1940. The requisites for an explosion are ever present in all soft-coal and many hard-coal mines. A certain combination of circumstances, such as a flame or an arc in a cloud of dust or in a body of gas or both may start an explosion at any time. The fact that the frequency and severity of explosions were lowered for 6 or 7 years is no guarantee that such freedom from explosions will continue, as the bad record of 1940 has shown, and underground workers should feel honor bound to exercise the utmost care so that they will not help to bring about the circumstances that will cause an explosion.Although mine operators bear the main responsibility for preventing explosions, miners can do many things to help. As about 9 out of 10 explosions begin at a working face, it is largely within the power of workers to prevent them. All miners should do their part willingly and should not defend a fellow workman from punishment, even from discharge, for disobeying necessary rules, whose disregard may cause the death not only of the safety-rule breaker but also of many of his coworkers.When a miner is careless and is injured some other way than by an explosion he may be the only one to suffer, but if his carelessness causes an explosion he not only endangers his own life but also that of every other man in the mine and possibly the lives of persons outside the mine.Experiments have shown that ignition of as small a quantity as 150 cubic feet of an explosive mixture of methane and air under certain circumstances can start an explosion that will traverse an entire mine. Thus, ignition of an explosive mixture of gas 1 foot down from the roof and 13 feet back from the face of a 12-foot entry might cause a widespread explosion if the right quantity and kind of dust were present. Many persons have ignited much larger quantities of gas without being killed, but they survived only because dust, confinement, and other conditions were not exactly ""right."""

Nov 1, 1940

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By Gerald T. Homce, James C. Cawley

Problem: CFOI and SOII data show that 2,287 U.S. workers died and 32,807 workers sustained days away from work due to electrical shock or electrical burn injuries between 1992 and 1998. Method: The narrative, work activity, job title, source of injury, location, and industry for each fatal electrical accident were examined. A primary causal factor was identified for each fatality. Results: Electrical fatalities were categorized into five major groups. Overall, 44% of electrical fatalities occurred in the construction industry. Contact with overhead power lines caused 41 % of all electrical fatalities. Discussion: Electrical shock caused 99% of fatal and 62% of nonfatal electrical accidents. Comprising about 7% of the U.S. workforce, construction workers sustain 44% of electrical fatalities. Power line contact by mobile equipment occurs in many industries and should be the subject of focused research. Other problem areas are identified and opportunities for research are proposed. Impact on Industry: Improvements in electrical safety in one industry often have application in other industries.

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting & Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. "V. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K Thomson, W. G. Derby, and the assistants of the writer, K. 1V.McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the aid of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate anyone method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of light-scattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2006

By Dupuy. Leon W.

"INTRODUCTION For many generations the Indian tribes of the southwestern deserts knew of the thermal springs of the Coso District in southwestern Inyo County, Calif. Belief in the reputedly healing qualities of the waters and muds of the area was widespread. F. J. Sanders discovered mercury in the siliceous sinter around the hot springs while he was exploiting the district as a health resort. In searching for new domestic sources of supply of strategic minerals, authorized under the Strategic Materials Act, 3/,the Geological Survey 4/ first examined the deposits, which were drilled and sampled by the Bureau of Mines in the spring of 1941.The deposits investigated comprised three units known, respectively, as The Devils Kitchen, Nicol, and Wheeler. Most of the work was done at the first two.Of particular interest in the Bureau's work on the project was the adaptation and use of the bucket drill as a tool for sampling shallow, soft ore deposit."

Mar 1, 1948

By W. D. Dietzman

This Bureau of Mines report presents a profitability analysis of producing crude oil by waterflooding. Included are the estimated costs of installation of water injection and producing equipment for waterfloods at 2,000 and 4,000 feet and the estimated annual operational expenses for each in west Texas. Using these cost estimates as a base for selecting a range of costs that are indicative of producing crude oil by waterflooding, a simulation technique was derived for determining the profitability under various conditions. Because of the large number of combinations of variables used in this study, a high-speed digital computer was utilized for the calculations. The variables include operational expenses, capitalized costs, price of the oil, annual production, and leasehold acquisition cost. The results obtained from the simulations are presented Fn the appendix. In addition, a nomographical approach was chosen for presentation of the profitability. Five nomographs are presented that can be used for fast estimation of the discounted cash flow (DCF) rate of return that might be expected from a prospective or active operation under various sets of assumed conditions.

Jan 1, 1974

By R. Demont, A. Pranesh, S. Rakheja

Ethical concerns of in-vivo procedures and poor repeatability of non-invasive techniques have been major limitations in estimating vibration-induced spine loads through experiments. The biodynamic models of seated human body exposed to whole-body vibration (WBV) have evolved for defining the frequency-weightings, enhancement of human responses to WBV, and developing anthropodynamic manikins for seating assessment activities. The widely reported mechanical-equivalent models, solely based on through- or to-the-body biodynamic response functions, do not seem to resemble the biomechanical structure and do not yield information on the dynamic loading and deflections of segments of concern, namely the spine. On the other hand, biomechanical models with representative anatomical structure and anthropometry are being attempted to simulate segmental movements and the coupling effects, using Finite elements (FE) or multi-body dynamics (MBD) formalisms, which could provide important insights into the inter-vertebral forces [1]. While the FE models pose considerable complexities primarily related to characteristics of the bio-material properties, the MBD technique with discrete rigid bodies offers the flexibility to create multi-segment models with relative ease and lower computational cost. In this study, a preliminary multibody dynamic model of a seated human body exposed to WBV along the vertical direction is formulated using MSC/ADAMS software. The model validity is demonstrated by comparing selected responses with the available measured data. Methods The seated human is represented by nine rigid body segments, including: head, neck, thoracic and lumbar torso, pelvis, hands and thighs, as shown in Fig. 1. The rigid bodies are coupled through different rotational and translational joints, some of which are force elements to allow vertical translations and sagittal–plane rotations of the segments. The measurements of transmission of vertical vibration through-the-body generally require subjects to voluntarily maintain a vertical head position to reduce head-accelerometer orientation errors. The head–neck–shoulder joint is thus considered to be rigid. The shoulders are assumed to be rigidly attached to the thoracic segment. The torso is made up of three (upper, middle and lower) segments connected by visco-elastic revolute and translational joints to permit relative pitch and vertical motions. The forces and torques generated by the joints are derived assuming linear stiffness and damping properties, which were identified from published studies. The pelvis is connected to the rigid seat by similar elements representing the visco-elastic properties of the buttock tissues. The two thighs are rigidly connected to the pelvis, while the segment masses are chosen from the anthropometric data for the 50th percentile male subject. The initial model parameters for the joints were obtained from [2]. The model was analyzed to determine the force-motion relationship at the buttock-seat interface expressed in terms of

Jan 6, 2006

By Jim Ploger, Peter W. Johnson

Bus drivers represent a large segment of the US transportation industry and research has shown an association between exposure to Whole Body Vibration (WBV) and the high rates of low back disorders. Impulsive WBV exposures have been recognized as a risk factor for low back injury and new guidelines exist for their measurement and assessment (ISO 2631, Part 5). Methods to accurately and better characterize the impulsiveness of WBV along with the temporal patterns of the exposures are needed. The development of a hardware and software system to measure continuous TWA and raw, impulsive WBV exposures and the design of a subsequent study are presented. Methods Using two Larson Davis HVM 100 as accelerometer amplifiers, small external batteries, and a Pocket-PC (PDA) with 1 Gb of compact flash memory, we can collect up to 16 channels of data for a full day 600 Hz. Tri-axial WBV exposures will be measured and characterized at the frame of the bus and at the driver/seat interface (seatpad accelerometer). Using a repeated measures design, 20 bus drivers will drive on selected routes which include both city streets and highways, and within and between subject components of variability and exposure determinants related to the bus, bus seat, the bus driver, and the route will be identified. Global Positioning System (GPS) data will also be collected and integrated with the WBV exposure data to facilitate the identification of the location, velocity and type of road associated with high average TWA and impulsive WBV exposures. This system may be used to develop administrative (alter speed and/or route of bus, systematically vary type of routes) and/or engineering controls (identify and trigger the need for street repair) to reduce high WBV exposures. Results Our portable Pocket-PC based data acquisition system is up and running and we can collect seven channels of WBV data (seat pan tri-axial accelerometer, bus frame tri-axial accelerometer and GPS data) continuously for a full shift. The software analysis of the data is complex but nearing completion. We have incorporated the vibration dose calculations from ISO 5321, Part 5 and have obtained a Matlab-based routine to appropriately weight the continuous signals. Discussion In summary, the measurement of WBV is complex but new technologies open avenues of collecting and assessing WBV exposures that were previously not possible. The standardization of impulsive WBV exposure assessment methods is needed to further the discipline and better enable comparisons across studies.

Jan 6, 2006

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifications, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and viability of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 1, 1984