Search Documents

By A. Erickson

The effectiveness of a loader-mounted fan on diesel vehicles combined with natural convection for ventilation of a dead heading (the patented Janelid system) was investigated experimentally. The results were obtained using CO2 as a tracer gas in a 1/4 scale model heading. Buoyant forces were scaled to establish similarity with full scale. For a loader moving in a typical load-haul-dump cycle, the loader-mounted fan reduced the tracer gas concentration by 26 percent compared with a reduction of 32 percent for a jet fan of four times the flow capacity.

Jan 1, 1981

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By R. L. Mazza

This final report on methods of reducing and controlling methane in coal mine gob areas indicates that vertical degas holes are beneficial to the mines of northern West Virginia working the Pittsburgh Coal. The USBM funded project involved the drilling and testing of eight vertical holes (four over longwall panels and four over room and pillar panels) based on a review of 13 previously in existence. Areas of observation included gas production history, flow entry profile, underground methane reductions, strata separations, and casing loads (accompanying subsidence). Observations led to the drilling of successful holes drilled short of the mine. Eleven gas production response to applied vacuum tests were conducted at nine degas holes under the contract. Significant production responses were recorded over longwall gobs.

Jan 1, 1977

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By David R. Alison

This study was conducted using field interview methods to determine the data and information requirements of the underground coal mining industry for improving mine ground control procedures in existing and future mines. The establishment of a central geologic and engineering information resource center with computer searchable abstract files that can locate and supply descriptive and case-study literature addressing specific mining problems is recommended. Research done under Bureau of Mines Contract J0395010, includes a Bibliography of Underground Coal Mine Ground Control Literature.

Jan 1, 1980

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

To improve communications between mine workings and surface locations during emergency situations and for administrative purposes. The Approach: Development of a device for interconnecting phone systems which permits two-way communication between a public telephone and a mine pagerphone by authorized personnel. How It Works: The system, developed by personnel at the Bureau's Pittsburgh (Pa.) Mining and Safety Research Center, makes connections between the public phone line and mine pagerphone line. As shown in Fig. 1., incoming calls are sensed by the ring detector (4) and the system "answers" the call electronically. To reach the pagerphone system, the caller inserts an audible tone of fixed frequency through the microphone of his telephone. This tone is produced by a miniature, pocket-carried tone generator and is detected by a tone recognition circuit (5). When this hap-pens, relay, switching, and logic circuitry (6) closes the connections between the two phone systems. Simultaneously, a page activator (9) places a DC paging voltage on the mine phone line.

Jan 1, 1974

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By Mark S. Redfern, Kim M. Corneliusa, Christopher A. Hamrick, Sean Gallaghera

Coal miners often handle heavy electrical power cables, weighing up to 10 kg per meter. These cables are manually lifted and attached to the mine roof to prevent damage from mobile underground equipment. Data suggest that workers who commonly perform cable handling tasks experience a high rate of lost time back injuries. In this study, six male underground miners performed a total of 12 cable-hanging tasks in standing, stooping, and kneeling postures, during which kinematic and ground reaction force data were collected. Reductions in vertical work space were found to result in a linear increase in the peak moment experienced by the lumbarspine (p<0.05). In restricted postures, peak moments were not significantly different in stooping vs. kneeling postures (p>0.05). Average lumbopelvic flexion during the tasks was highest in stooping conditions, followed by standing and kneeling exertions (p<0.05). Implications of this data with respect to design of cable handling tasks are presented and discussed. Keywords: Biomechanics, posture, low back pain, restricted workspace, mining

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By H. D. Kline

This paper describes the methods of mining and washing brown iron are in 1957 at the Sawyer mine, leased by Wayne County Mining Co., and the Fore mine, leased by Four Mining Co., both in southern Missouri; it is one of a series prepared by the Federal Bureau of Mines on mining and milling methods and costs in various districts of the United States. The Sawyer mine is in Wayne County, about 10 miles north-northeast of Williamsville (fig. 1); the Fore mine is in Howell County, about 20 miles southwest of West Plains (fig. 2). Both are open-pit mines from which the crude are was upgraded by washing and hand-sorting to produce are of grade and quality suitable for sale to operators of iron and steel furnaces. The operations described are typical of many others that produce or have produced marketable brown iron are from small sedimentary deposits, several hundred of which outcrop on the crests or hill sides of southern Missouri (fig. 3). The 1957 production of marketable brown iron are by 40 separate operations in the southern part of the State was 281,427 wet long tons, valued at $1,637,243. Production from the Sawyer mine that year was 17,000 dry long tons of washed are, and from the Fore mine, 20,816 dry long tons.

Jan 1, 1960

By Lucia Kuizon

The Pinnacles Wilderness Contiguous Wilderness Study Area (WSA) (CA-040-303) is 30 miles south of Hollister, CA, in San Benito and Monterey Counties. It is composed of five parcels of public land totaling 5,838 acres adjacent to the Pinnacles National Monument. The U.S. Bureau of Land Management later reduced the size of the Recommended Suitable Area (RSA) to 2,200 acres. U.S: Bureau of Mines personnel examined the entire WSA in May 1984. The WSA is underlain by Tertiary sedimentary and Cretaceous plutonic rocks. Diatoms occur in interbedded tuff, shale, and sandstones in the northern part of the WSA, but outside the RSA. In 1984, there were no mines, prospects, mining claims, leases, or mineral resources in or within one mile of the study area. No energy minerals were identified; however, an oil well was drilled in 1951 in the northern part of the WSA, but outside the RSA; it was a dry hole.

Jan 1, 1985

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

By R. Stefanko

This study concerns itself with the effects of diesel exhaust on mine ventilation systems. The approach here consisted of the development of mathematical models for emissions, dilution, and dispersion of gaseous pollutants from diesels. The general scheme was to use partial differential equations to predict concentration growths. Specifically, the following situations were modeled: 1. A single stationary diesel engine working in a single roadway. 2. A single diesel engine moving with uniform velocity in a single roadway. 3. Multiple diesel engines moving continuously in a cycle in a roadway with appreciable leakage. 4 Multiple diesel engines moving continuously in a cycle in a roadway with little or no leakage. 5. Multiple diesel engines moving randomly in a roadway with uniform air velocity.

Jan 1, 1974