Search Documents

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

This study was conducted to determine the feasibility of using large tractor dozers in land reclamation of strip-mined areas. The procedures used are patterned after engineering models developed for evaluation of military ground vehicles in cross-country operations. Tractor dozer manufacturers furnished information on capabilities of existing equipment and ideas on the practicability of using dozers larger than those currently available Generally, they believe that current dozers in the 500? to 700-horsepower range are about as large as can be built and remain economically feasible. However, one manufacturer has a wheeled dozer rated at 1200 horsepower, and another is testing a tracked dozer of about the same horse-power.

Jan 1, 1975

By Herbert H. Einstein

Instability of rock slopes often occurs in the form of excessive movement of bodies that are bounded by discontinuities. The well known limit equilibrium analysis for wedges and blocks suffer, however, from procedural simplifications and from the basic deficiency of limit eguilibrium analysis--the rigid body assumption. Thus, stability analysis for 2-and 3-plane wedges with a wide range of additional features regarding failure modes and external forces have been developed. The deficiency, due to the rigid body assumption, was corrected by an approach that includes the effects or the in-situ stress field and of the stiffness of discontinuities. The final step in making limit equilibrium approaches more valid was achieved with the method of artificial supports which makes it possible to identify among all possible failure modes the critical one and to determine the corresponding factor of safety. The analytical development includes the creation of appropriate computer codes and routines for programmable pocket calculators.

Jan 1, 1979

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By M. K. McCarter

Previous investigations suggest the possibility of determining shear strength of geologic materials by measuring the force necessary to rupture the web between two closely-spaced, parallel holes using a borehole jack. Current research using finite element modeling and laboratory testing of intact rock indicates that web failure initiates by tensile fracturing induced by a complex stress field. Based on these results, a theoretical justification for relating web strength with shear strength appears unlikely for holes of equal diameter spaced two diameters apart. Empirical results, however, show a strong correlation between average web strength and average unconfined compressive strength for some rock materials under laboratory conditions. A good correlation also exists between residual web strength and the residual angle of friction under the same conditions. This research project involves the construction and field testing of a large borehole jack. The jack is designed to operate within a conventional 12-1/4 inch rotary blasthole common to open pit mining. The system is capable of exerting approximately 800,000 pounds on curved platen measuring roughly 4x24 inches. Field tests indicate that the system will operate in a mining environment, and preliminary results suggest the possibility of using the force-displacement data generated by the jack to rank the competency of material within a mine bench.

Jan 1, 1982

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By Francis X. Cannaday

Equipment and techniques were developed with Bureau of Mines facilities for measurement in the laboratory of sonic shear wave velocity in variously shaped rock specimens in a wide range of sizes. A variety of rock types was tested. The shear wave front is produced by electronically excited, piezo-electric ceramic) disk-shaped transducers. Transmitter and receiver are interchangeable. Special equipment components were Bureau produced; other components were commercially available. The equipment permits quick measurement of shear wave velocity on variously shaped specimens with a minimum of specimen preparation. The technique, under favorable conditions, allows for determination of the moment of arrival of the shear wave when it is superimposed on a weak longitudinal wave.

Jan 1, 1968

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By Francis E. Federspiel

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resource potential of the Log Cabin Saddlebag, Hall Natural Area, Horse Meadow, and Tioga Lake RARE II areas in Mono County, California. These areas, along the east slope of the Sierra Nevada, are underlain by Paleozoic metasedimentary and metavolcanic rocks of the Log Cabin Mine and Saddlebag Lake roof pendants. The roof pendants are in Cretaceous granitic rocks. Pleistocene volcanic flows cap some of the older rocks, and glacial till and outwash locally cover the bedrock. The region was eroded by alpine glaciers. Four parts of the Log Cabin Saddlebag area have moderate gold and silver resource potential. Moderate potential for gold and silver resources was identified in one part of the Hall Natural Area and low potential for tungsten and molybdenum in two other parts (fig. 1).

Jan 1, 1982

By John F. Elliott

Six major trends that have had and are continuing to have major effects on the use and supplies of pig iron and scrap in the United States are (a) gradual replacement of the basic open hearth furnace (OH) by the basic oxygen furnace(BOF); (b) use of the electric furnaces for the production of plain-carbon steels, a trend which is closely related to the first; (c) United States changing from being a net exporter to a net importer of steel; (d) replacement of ingot casting by strand casting; (e) increased exportation of scrap; and (f) the lack of growth of the capacity of the U. S. steel industry to produce pig iron in the last 5 to 8 years. This report gives an analysis of the relationships between these trends and the use of processes for the production of raw steel in solidified form.

Jan 1, 1975

By Robert W. Metcalf

Corundum, natural alumina, or aluminum oxide (A1203) is the hardest mineral known except diamond. Theoretical composition is Al 52.9 percent and 0 17.1 percent, but it always contains small quantities of impurities, chiefly silica, iron, and lime. The melting point of corundum is above 1950° C., and it is insoluble in the strongest acids. Its hardness (9 on the Mohs scale) varies slightly according to purity, and its specific Gravity ranges from 3.95 to 4.10, 4 being a fair average. The index of refraction is 1.760 to 1.768 and its streak is white. Luster is adamantine to Vitreous, come specimens pearly, and color varies widely from white, gray, pink, and blue to black, brown, or bronze. Gem varieties are transparent or translucent, and of more brilliant coloring - red, blue, yellow, purple, or green. Corundum occurs in opaque massive or block structure with parting planes little developed or only roughly delineated and in granular form as minute crystals or small, irregular grains interspersed throughout the contact zones of schists and gneisses.

Jan 1, 1944

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By F. A. Penning

This report describes the development of skip and guide desings for vertical shafts in deep vein mines. Skip and guide systems for bottom dump skips are identified as being used in current practice. Mine visits were made to obtain current information on the needs and problems of operating mines. Methods of structural and mechanical analysis of skip bodies and bails are outlined. A dynamic computer model was written to find the dynamic interaction between skips and guides for guides with geometric misalinements. A materials evaluation section identifies currentavailable and applicable materials that can be used effectively for new skip construction. Guide materials are also presented. Analysis includes the economies resulting from streamlined buntons and from low skip payload ratios. Selection of materials is based on strength, abra¬sion and corrosion resistance. Design requirements related to the shaft environment are presented. Consideration for the selection of guides and buntons is also given. Conceptual design includes the concept of cylindrical skips, center-seeking guide rollers, and asymmetric bail design to decrease dynamic interaction. An outline for field tests is presented. Future research areas are: testing, guide geometry measure¬ment, advanced suspension, dynamics, and structural configurations.

Jan 1, 1977

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Pedro Lilienfeld

This report presents a design and cost investigation for several alternative versions of a field-worthy mining machine-mounted respirable dust monitor. Three main design variations are considered: (a) light scattering sensing, (b) Beta-filter tape sensing, and (c) a combination of the two preceeding methods. Eventual instrument production coats as a function of design complexity are tabulated. Cost estimates for the development and field testing of field-worthy prototypes are also presented. A general discussion on the technical aspects of these design alternatives is included following a modular-hierarchical approach of progressive complexity. The technical background to this report has been provided by the experience and results derived from the work performed under U.S. Bureau of Mines Contracts Nos. H0166097 and H0377092.

Jan 1, 1980

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008