Search Documents

By Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Ahmet Varol, Ertugrul Kaya, Turgay Ozat

This paper presents analysis of environmental effects induced by cautious blasting during the construction of the Istanbul Subway 4 Levent - Ayazaga Darulsafaka Metro Tunnel Project carried out by the contractor, located at Northern Istanbul in Turkey. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S6-7-8 shafts of this tunnel route, ground vibration components were measured carefully by using five vibration monitors during the construction of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighboring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 107 records belong to 51 shots were analyzed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for these tunnel excavations and suggested for the test sites in order to estimate particle velocity of the ground vibrations. As a result of the studies, some practical charts are created in order to minimize the psychological effects of the shots, and simplify the authorities of shots’ job. And last but not least, make sure that the shots will be done in a controlled way.

Jan 1, 2011

By Jason Baird, Joshua Hoffman, Phillip Mulligan

The purpose of this report is to address the method of reducing the overall explosive weight of Explosively Formed Projectiles (EFPs) while still achieving satisfactory performance. This reduction is crucial in order to comply with outdoor explosives testing standards for Missouri University of Science and Technology’s (Missouri S&T’s) Experimental Mine. Initial EFP design testing exceeded given limitations, making reliable data difficult to ascertain. EFPs must be tested outdoors to allow for specific information recordings which aid in defending against them.

Jan 1, 2010

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

By Ekin Güngor, Berkant Ozdemir, Erkan Bayrak, Serdar Ergün, Sedat Esen

"This paper presents the final wall blasting practices at Eldorado Kisladag Gold Mine in Turkey. Benchmark and improved wall control designs were explained in detail. Kisladag Mine has been implementing a high quality slope stability program on-site. The quality of pit walls is generally considered excellent, with very few wall failures being evident and with presplit hole barrels prominent in most areas of the pit. However, a minor scale slope failure occurred recently at the north-east section the pit. A project was initiated to diagnose the cause of the crest loss and evaluate ways to limit its effect on final walls. Final wall blasting practices and geotechnical designs were evaluated. The work presented in this paper showed that changes to the blasting and geotechnical parameters are required atthe north-east section of the pit. Geotechnical design changes were 10 m bench heights with 70 ° slope face angle at that specific area. Having implemented several geotechnical and blast design changes (elimination of the subdrill for the catch bench, appropriate primer location, more favorable blast tie-up and delays), the crest loss was minimized significantly (<1.5 m) (<5 ft)."

Jan 1, 2017

By Kush Patel

This paper presents methods currently available for the evaluation of bulk explosives and discusses the results of the evaluation of bulk explosives using each of the methods. Through the preliminary experimental analysis, wet chemistry and the Bulk Explosive Analyser were found as methods most suitable for the evaluation of bulk explosives. This paper also presents data obtained from the experimental comparison of the wet chemistry method and the Bulk Explosive Analyser.

Feb 1, 2020

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020

By E Novikov, D Johansson, U Nyberg, A Beyglou, N Petropoulos

Fragmentation is an important factor for improving downstream processes in mine operations. Six trials have been conducted at the Aitik copper mine to investigate the effect of ultra-short inter-hole delay times, i.e. smaller than 1 ms/m of burden, on fragmentation. Swelling, MWD data, and crusher efficiency were also evaluated for trials. According to the results, the effect of examined short inter-hole delay times, i.e. 0.14 to 0.86 ms/m of burden, on fragmentation was found to be marginal. Delay time of 0.43 ms/m of burden resulted in slightly finer fragmentation and larger swell; however, the effect of short delays was overshadowed by the effect of small variations in specific charge.

Jan 1, 2014

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By Jim Peterson, Ricardo Freire, Mason Biernat

Variable nature of rock and face conditions, varying execution and changing nature of blasting are making ongoing optimization challenging. Intelligent planning and on-going analytics are required to mitigate variability and convert blasting into a predictable outcome by use of technology. Blasting operations generate a huge amount of data which can be used intelligently for optimization. In this paper, details are provided of a system which is used for blasting data collection in the field – Key details around blast parameters, explosives, initiating system details, video, photographs, vibration and fragmentation are collected in a cloud-based platform. Data can also be collected through a mobility device in the field (even without internet connectivity) and synchronized with cloud-based system. Also, data from various sources can be imported in excel formats in the software including from upstream and downstream processes from blasting. App also gives indication about exceeding of vibration, air blast overpressure, fragment size etc. Thus, making it possible to perform QA-QC before charging and deciding initiation timing and sequence at the blasting site. The data can be processed and analyzed to spot trends, help predict events, and formulate strategies at the design and execution stage. Data gathering of blast parameters, explosive used processing and analysis can be used to optimize operational efficiency, improve safety and environmental controls.

Jan 1, 2019

By Jihan Farhan Lubis, Putu Chandra Darmansyah

Ground vibration caused by blasting has become a common concern, especially when blasting is conducted near buildings or structures. Uncontrolled vibrations can potentially damage nearby infrastructure if appropriate control measures are not implemented. PT Tambang Semen SUKABUMI, a limestone mining company, is planning to carry out blasting activities near a crusher building located approximately 80 meters away. This building is classified as a Class 5 structure, with a maximum allowable Peak Particle Velocity (PPV) of 40 mm/s, in accordance with the Indonesian national standard SNI 7571:2023. To ensure compliance with this limit, a Signature Holes Analysis (SHA) was conducted using the Hanwha HEBS II electronic detonator initiation system. This analysis measured ground vibration from single-hole blasts, with the average vibration from three SHA holes recorded at 49 mm/s. A site constant analysis using the scaled distance formula yielded a multiple R value of 0.87. However, the ANOVA table showed a significance-F value of 0.24, which is greater than 0.05 indicating that the regression model used for prediction was not statistically significant. Using the SHA data and assuming a maximum of 30 blast holes, a recommended delay timing of 22 × 15 milliseconds was selected. This produced a predicted PPV of 17.25 mm/s. The comparison between predicted and actual PPV values demonstrates that the delay configuration derived from Signature Hole Analysis provides reliable results. The observed deviations range from -16% to +29%, with an average deviation of only 8%, indicating a high level of accuracy and consistency. Using the actual blast data, three model prediction were applied for predicting the most accurate prediction that close to the actual value. The SHA method, utilizing actual single-hole vibration measurements and optimized delay timing, provided the lowest average deviation of ±8% and the smallest absolute error (2.45 mm/s) from actual measurements, demonstrating high reliability for sites with sufficient signature data. Meanwhile, the log-log regression model yielded the highest coefficient of determination (R² = 0.751) and the smallest prediction deviation (3%) when standard deviation margins were considered, making it highly effective for predictive modeling.

Jan 26, 2026

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

By Gordon Lovegrove, Jeffrey Leob, Dwayne Tannant

It has long been known that the combination of aluminum (AL) powder to ammonium nitrate (AN) / fuel oil (FO) can greatly enhance fragmentation or ultimately reduce the number of blast holes in a pattern. Decades of research have meticulously provided optimal AL:AN:FO ratios showing dramatic increases in energy output levels, yet widespread use of aluminized ANFO (ALANFO) has yet to replace the use of ANFO in the blasting world today. This may be due to the perception that the upfront, increased cost of materials deters the selection of this advantageously modified explosive. Researchers have explored this question and promote ALANFO by pledge of massive reductions in day-to-day operational costs. However, in these analyses there is a complete disregard for the external costs of the material; the environmental effects and sustainability considerations of the product. A holistic social cost-benefit analysis of ALANFO shows that an admittedly high-cost explosive does indeed provide an output which contains a wealth of operational savings in typical blast patterns. However, the immediate, on-site costs and savings do not define the limitations of this analysis. A complete comparison of the externalities including the environmental and sustainability considerations of the aluminum by-product life-cycle, and the environmental impacts of both the refinement of ammonium nitrate prills and the acquisition of sufficient fuel oil are also assessed. A savings of $216,000 / year through the use of ALANFO in one particular case study was recalculated to an increase in drilling and blasting costs of $188,000 when the external costs of aluminum, ammonium nitrate, and fuel oil are included analysis. The results of this analysis are intended to improve contractors? selection of explosives by providing additional societal and environmental factors into the equation, in preparation for an exponential global shift to greener business operations, while allowing them to remain competitive.

Jan 1, 2011

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Agus Sasmito, Akash Adhikari, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Previous studies on blast fumes(CO + NO2) clearance and workplace re-entry time have overlooked the effects of toxic gases entrapped in the muckpile. The currently available models forcalculatingthe mine re-entry times assume that all post-blast fumes are emitted upon detonation. However,recentstudies reportedthat as much as 60% to 70% of the fumes or gases produced during an underground development blasting couldremain entrapped in the adjacent rock mass or in the muckpile. Entrapped fumes are slowly released,and when disturbed, high concentrations are released, representing a possible risk during the digging and transportation of the muckpile. This study uses CFD, SC-Flow software to understandthe behaviorof the entrapped fumes and theireffect on mine re-entry time.

Feb 1, 2020

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025