Search Documents

By Kunihisa Katsuyama, Yuji Ogata, Takuya Taguchi, Toshinori Arikiri, Yuji Wada, Kiyoshi Hashizume

The impact sensitivity of hot emulsion matrices was examined to investigate the safety assessment in the emulsifying equipment which forms the emulsion matrix in a water-in-oil type emulsion explosive. The sensitivity could not be evaluated by the small fallhammer test device commonly used in Japan. Therefore, a large fallhammer test device was used. It was confirmed that an explosion, a decomposition, or a no-reaction took place according to the degree of the impact. When a decomposition took place in the hot emulsion matrix, the behavior of it was investigated further by a DDT test. It was found that a decomposition, or a no-reaction occurred according to the degree of confinement.

Jan 1, 1997

By D T. Froedge

Before this study was started, literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast-induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet.

Jan 1, 1983

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By Jack Eloranta

Transmission of sound through the atmosphere is affected by local conditions. Anecdotal accounts of the sound of cannon fire traveling great distances go back to the Civil War. The Royal Society published a paper near the turn of the century concerning the reports from the cannons fired in London at the funeral of Queen Victoria. Early computers were used by the U.S. Army at Aberdeen in Maryland in the 1950’s to model airblast problems during munitions demolition. Today’s blaster has to have access to weather information beyond a simple local forecast. Surface winds, winds aloft and temperature profiles have a dominant role in neighbors reaction to blasting. Many ground vibration complaints are really airblast complaints. Blasters who maintain ground velocities under . 1 inches/ second are often perplexed by complaints from distant neighbors, even when local monitoring shows airblast to be under 110 dB. This paper will help the blaster identify warning signs of high airblast conditions.

Jan 1, 2000

By Roger Lucas, Dale Nies

The McLaughlin Mine is an open-pit disseminated gold mining operation. Homestake Mining Company's approach to solving some of the blasting problems inherent to this type of deposit provide an interesting case history. Geology, although unique and site specific, is overall similar to other mines within the Western United States over-thrust belt and demonstrates an excellent example of the blasting conditions and requirements common to most of these operations.

Jan 1, 1990

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By Kirlk Yeager

"Ammonium nitrate (AN) is commonly mixed with a wide variety of additives to produce specialty formulations. Two additives commonly utilized are sodium nitrate (SN) and sodium nitrite (SNi). Application of the nitrite is primarily limited to gassing of emulsions. The nitrate, however, is incorporated in a wide variety of formulations. The effect of both these materials on the thermal stability of AN was examined. Experiments initially utilized lab-scale testing methods (sub-milligram sample size), such as differential scanning calorimetry (DSC), with scale-up to cook-off analyses (16 g) eventually applied. Labscale testing indicated that the presence of SN and SNi (both at 5 wt%) produced no harmful effects on the thermal stability of AN. The cook-off results did not agree with those from the lab-scale analyses, with both SN and SNi creating tremendous thermal destabilization of AN. These effects were seen at additive levels as low as 0.1 wt%. When SNi was employed as the additive, cook-offs became violent enough to create explosions in the testing apparatus. Although SN did not create as spectacular a destabilization, it did lower cook-off temperatures to approximately the same level as SNi. The dangerous situation created by SN andSNi seemed to be limited to cook-offs conducted in sealed vessels. If the SN/AN or SNi/AN formulations were allowed to cook-off in vented vessels, the thermal destabilization of AN did not occur. These results seemed to indicate that even “trace” amounts of what might ordinarily be viewed as benign additives could create significant destabilization of AN-based explosives under proper circumstances. Conditions created by blocked pumps, or deep boreholes could well overlap those produced in sealed cook-off vessels. In addition to showing the hazards potentially created by “benign” additives, the study also stressed that experiments designed to evaluate thermal hazards must include duplication of field variables to the fullest extent possible. "

Jan 1, 1999

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By J R. Phin

The properties of all available modern blasting initiation techniques are reviewed. Primadets are nonelectric initiators, the nonelectric features of the system eliminates concern of premature initiation from static or stray currents. The loading techniques are simple and a minimum of training is required. There is no limitation in the number of necessary sequences in which the Primadet need be connected for initiation. This flexibility improves vibration control,and often reduces costs due to increased fragmentation.

Jan 1, 1975

By Shulin Nie

The dead-pressing phenomenon in emulsion explosives is wellknown. Research work on this subject has been carried out at the Swedish Detonic Research Foundation for the last few years. Several experiments with emulsion explosives under dynamic pressure condition have been carried out both in iron pipes and in blast holes in rock. The main object was to study the critical amplitude and duration of the pressure causing the explosive to be dead-pressed.

Jan 1, 1993

By W. J. Birch

The dedicated documenting of blast design and vibration monitoring results forms part of the best practice methodology for today’s blasting operators. This allows regression curves to be constantly updated and in turn compatible charge weight determinations are based upon the most current data. The point can arise however when so much data becomes agglomerated that variations in blast design, geology or monitoring location response and their effects can pass unobserved and start to have an adverse effect on the forecasting capability of the regression due to a deterioration of the standard error statistic. The simple solution would be to only compile like-for-like blasting returns, but this prospect can quickly become unworkable due to the number of potential variables. In addition it is very difficult to spot subtle variations by simply examining a standard scaled-distance curve mainly due to the intrinsic data scatter that is always present together with the logarithmic nature of the regression curve. If indeed a variation is thought to be apparent, how can the degree and magnitude of its influence to be quantified? The Likelihood Ratio Test when applied to regression data can diagnose subtle variations between data sub-sets and provides a comparative statistic as to the degree of variation. By analysing datasets in such a way, levels of compatibility are obtained, indicating which sets can be combined in order to increase prediction capability.

Jan 1, 2004

By David W. Zeeb

The use of an ordinary VHS video camera and a four-head player can be an effective tool to analyze surface blasting. The necessary equipment can be purchased for under $1,300 and will allow frame by frame or slow motion viewing of a blast in 33.33 millisecond increments. Rock breakage, movement, and timing can be studied in high quality slow motion. These studies can result in improved blasts by showing things that the eye can miss in real time.

Jan 1, 1992

By Callie Covert

This paper describes the application and results of a more efficient method of breaking boulders using dynamite and water. This method is being used for the disposal of boulders that result from pinnacle and cap rock remaining after blasting on highways and job sites. This method is a faster and less expensive use of dynamite to reduce oversized boulders than the conventional rock hammer. The problem with excessive fly rock has been substantially reduced when using this technique over traditional methods.

Jan 1, 2001

Coal strip mine operators in Western Canada often mine steeply-dipping multiple coal seams in mountainous terrain. The ability to fragment the rock waste layers above and below these seams with minimum disruption of the seams in large blasts normally involves decked charges in large rotary boreholes. Mining these seams may take two or more separate blasts to break the waste wedges above and below the coal, but these wedges can be blasted in a single shot for better mining efficiency.

Jan 1, 1985

By E Emery Jr Gray

The City of Richmond, in an effort to improve sewage treatment facilities, designed an invert syphon to cross the James River at Fulton Bottom. The design criteria called for installation of two 36-inch pipe' lines at an elevation of -35 with the mean water level being at elevation 00. This paper discusses the actual method of construction used to blast the river bottom. Choice of excavation equipment, nature of the river, as well as the geological structure, were taken into consideration.

Jan 1, 1979

By Jerome S. Brower

Quadrex-L is a two component liquid explosive which was developed by J. S. Brower & Associates, Inc. to facilitate handling and shipping, and use in unique applications, while emphasizing safety. It may be advantageously used for all explosive applications. Quadrex-L can be introduced into a preinstalled container configuration and may be easily drained or flushed from these containers when necessary to do so. This characteristic can be effectively utilized to reduce the hazard period during assembly or disassembly operations.

Jan 1, 1975

By Douglas Anderson

In the early 1980s, a method for controlling blast vibrations other than by modifying the Scaled Distance came into use. Research studies had indicated that blast vibration could be simulated by detonating a signature hole with the vibration monitored at critical locations, and then using a computer to superpose the waveforms with varying delays. By choosing delay times that create destructive interference at frequencies that are favored by the local geology, the “ringing” vibration that excites structural elements in houses and annoys neighbors could be reduced.

Jan 1, 2008

By Dale Preece, Stephen Chung

Mining and quarrying industries recognize blasting as the most effective method for breaking and removing large volumes of rock. However, the economics of blasting are often offset by the costly trial-and-error approach. Researchers in the field of blasting therefore design models to help eliminate the number of trials before finding the best feasible solution. Because of the complexity of blasting, a capable model would allow the designer to look at more than one variable at a time so that the most critical factor can be tackled.

Jan 1, 2002

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987