Search Documents

By Larry R. Fletcher

The Bureau of Mines obtained blasting accident data from the Mine Safety ant Health Administration (MSHA), U. S. Department of Labor. These data were analyzed to determine the most frequent causes of accidents in mine blasting. Accident totals for 1971 through 1981 are tabulated for metal-nonmetal and coal mines both surface and underground. In the past 11 years (1971-1981, inclusive) there has been an annual average of 9 fatal and 121 nonfatal blasting accident victims. Underground mining averaged 6 fatal and 93 nonfatal injuries each year.

Jan 1, 1983

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By C H. Ryu

This paper presents a simplified two-dimensional numerical model of block fragmentation in a Jointed rock mass during the late or throw stage of a blast after wave effects have subsided. The model is based on the distinct element method. Examples illustrate the approach and allow for a comparison of effects of Joint patterns on fragmentation and resulting block motion.

Jan 1, 1986

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980

By Robert A. Cummings, Francis S. Kendorski, Charles H. Dowding

During the summer of 1980, a field project was carried out to determine the stability of the beautiful and dramatic natural limestone pinnacles (locally termed "Hoodoos") at Bryce Canyon National Park, Utah, when subjected to ground motions and airblasts resulting from proposed strip coal mine blasting. The concern arose from environmental considerations associated with the proposed development of a large coal strip mine which would approach within 4 miles of the park. The pinnacles range up to 150 ft in height and are quite slender, producing a fragile appearance. The remoteness and ruggedness of the area required a field camp, and 4-wheel drive vehicles, helicopters, and snowcats for support. Portable magazines were necessary to store the more than 7 tons of blasting agents and explosives required. In conducting the blasting, great attention was paid to environmental impacts. In the field, a target pinnacle was selected and instrumented with mechanical strain gages, and research seismographs that required helicopter placement.

Jan 1, 1982

By Dennis Dobson, Keith M. Henderson

Lone Star Industries, Inc. in Cape Girardeau, Missouri operates an open pit mine to produce limestone for its portland cement manufacturing plant. The present mining method, for safety and legal reasons, requires a set back from the property line, a berm, sloped overburden, and vertical rock walls with catch benches.

Jan 1, 1997

By Robert Slivinski, Kyle Hobbs, Michael Stern, John Willox, Brad Jewson

Prairie Mines & Royalty Ltd. produces over 12 million tonnes annually of thermal coal for TransAlta’s Sundance and Keephills power stations from the Highvale Mine. This opencast mine is next to a lake and is surrounded by cottages and farms, which means that blast vibrations and air overpressure have to be kept to a minimum.

Jan 1, 2008

By Joshua Hoffman, Catherine Johnson, Braden Lusk

The practice of dual initiation using precise timing from electronic detonators in boreholes is thought to be beneficial for increasing fragmentation at a desired location in the rock strata. This increased capacity for fragmentation is understood to be a product of both the collision of detonation waves in the explosive column and an increased energy liberation rate, each resulting from dual initiation. In addition, the collision of shock waves from two adjacent blast holes is suggested to improve fragmentation at the location the two shock waves meet, which can be controlled with precise timing. This paper presents the results from scaled laboratory experiments where converging detonation waves and shock waves were studied.

Jan 1, 2014

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020

By James G. Stuart

For precise control and timing of a blast, people use electric detonators. Most of these contain a fine metal “bridgewire,” that heats to the required burning temperature when electric current passes through it. Users should be careful. Stray voltage can fire these detonators. Some designs are particularly susceptible to electrostatic-discharge (ESD). We will discuss some of the accidents we have encountered in our forensic work. We will recommend specific safe procedures for handling and firing these devices.

Jan 1, 2005

By J J. F Smith

The application of pneumatically loaded ANFO for underground mining has continued to increase year by year since the technique was first developed and introduced underground during the early 1960's. Improvements in the manufacturing process for explosives grade prills, the design and construction of more efficient AN prill-fuel oil blending equipment, and the introduction of more durable and reliable pneumatic loaders have promoted the wide application of the relatively low cost blasting agent, ANFO.

Jan 1, 1982

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990

By Travis Watts, Chris Prater, G. T. Lineberry

Moving overburden at minimal cost is becoming increasingly important to coal mining companies throughout the U.S. The coal market is currently doing well, with an average spot coal price for Central Appalachia product (12,500 Btu, 1.2 SO2) standing at $62.00 for the week ending November 11, 2005, so it is at this time that companies stand to achieve healthy rates of return on their investments. Cast blasting is one method of blasting used effectively by some surface mining operations. This method allows most of the overburden to be removed and placed (cast) directly in the spoil pile by the use of explosive energy. With the proper design of a cast blast, a high percentage of overburden material can be directed into piles without the use of earthmoving equipment, hence increasing production and lowering the cost associated with overburden removal.

Jan 1, 2006

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Wayne Rogers, Sarma Kanchibotla, Alan Tordoir, Bryon Bisiauz, Seth Ako, Eric Engmann

Blast induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered.

Jan 1, 2012

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By W. J. Birch, R. Farnfield

All shock-tube based initiation systems have a time lag relating to the propagation velocity of the shock-tube itself. This paper examines the exploitation of this inherent time lag to achieve delay blasting with accuracies approaching that achievable with electronic systems albeit over a much shorter delay range. The system employed consists of a combination of standard shock-tube, plain detonators and various shock-tube branching components. The accuracy of the complete system depends on the scatter in delay time induced by each component. In order to quantify this scatter a series of trials were undertaken to determine the variability for each component. These trials are described along with a detail statistical summary of the data recorded.

Jan 1, 2009

By Francisco Leite, Tomi Kouvonen, Bianca Saraiva, Vinicius Miranda, Auã Oliveira

One of the main challenges facing mining engineers is to draw up a plan that can be implemented in a timely manner, taking into account the operational variability of the mine’s production processes. These plans are often drawn up based on deterministic modelling (provided there are a set of known inputs that will result in a single set of outputs), when in truth we are talking about stochastic events (the cycles involved behave like random variables and their nature may be studied and reproduced). The result of using this kind of methodology can lead to non-optimized intuitive choices, which may harm the long-term targets defined by the planning team. Based on this principle, this document investigates the simulation of the rock fragmentation process in an open pit mine to assess the stochastic behavior of the loading and haulage operating cycles. The data assessed by the simulation process were the total costs of these operations in function of the powder factor. Based on a sample set data items, it was possible to check the probability distribution of the event as a Poisson distribution, applied to the loading and haulage cycles. The simulation consists of the repeated sequenced reproduction of these events (Monte Carlo simulation), in order to find the configuration that best fits the loading and haulage operations. By integrating these systems, it was possible to better understand the influence of the blasting in these operations, and as such to reduce the associated costs.

Feb 6, 2023

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990